Datasheet
Temperature Sensor ICs
Low Current Thermostat Output
BDJxxx0HFV Series
General Description
BDJxxx0HFV series is a thermostat output temperature
sensor IC with built-in temperature detection element,
constant current circuit, and a high-accuracy reference
voltage source in one chip. Temperature detection can
be realized at ±2.5°C accuracy without the need for a
complicated design. It is best suited for portable
equipment of micro- and low-current, power down
function, and battery drive. It is possible to use it for a
wide range of applications such as heat detection and
temperature monitors because it provides an analog
output in addition to the thermostat power output.
BDJxxx0HFV series has 5 products at 55°C, 60°C,
65°C, 70°C, and 80°C detection temperature.
Key Specifications
Power Supply Voltage Range:
2.4V to 5.5V
Supply Current:
Normal Function mode
7.5µA (Typ)
Power Down mode
0.3µA (Typ)
High Accuracy Thermostat:
±2.5°C (Max) @Ta=55°C to 80°C
Sensing Temperature Hysteresis:
10.0°C (Typ)
High Accuracy Analog Output:
±2.5°C (Max) @Ta=-30°C to +100°C
Analog Output Temperature Sensitivity:
-8.2 mV/°C (Typ)
Operating Temperature Range: -30°C to +100°C
Features
Detection Temperature lineup at 55°C, 60°C, 65°C,
70°C, and 80°C (5 products)
Built-in power down control function.
(Min PD Interface Voltage is 1.5V)
Low thermal resistance package (Typ 187°C/W)
ESD Rating of 8kV (HBM)
OS Output Active L
Package
W (Typ) x D (Typ) x H (Max)
Applications
Cellular Phone, Digital Camera, Thermal Protection for
Electrical Equipment (Notebook PC, FPD-TV, etc.)
HVSOF5
1.60mm x 1.60mm x 0.60mm
Typical Application Circuit
Please adjust Capacitor
according to the noise condition of
the set.
TEMP
1
IREF
VDD
5
VREF
TEMP
SENSOR
1µF
Please adjust bypass
Capacitor according to the
noise condition of the set.
0.1µF
GND C
2
PD
3
PD
C
+
-
OS
4
Please add pull-up of over 10kΩ for
the OS output terminal.
○Product
structure：Silicon monolithic integrated circuit
.
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
○This
product has no designed protection against radioactive rays
1/13
TSZ02201-0M2M0F515110-1-2
06.Nov.2015 Rev.001
BDJxxx0HFV Series
Block Diagram and Pin Configuration
TOP VIEW
TEMP
1
IREF
5
VREF
GND
2
TEMP
SENSOR
PD
3
PD
4
OS
VDD
Pin Descriptions
Pin No.
1
Pin Name
TEMP
Function
Output voltage in inverse proportion to
the Temperature
Ground
Power Down Control
H: Normal Function mode
L: Power Down mode
Digital Thermostat Output
H: Thermostat and Analog Output operation.
L: Power Down state.
Open-Drain Active-Low.
Use pull-up resistor of more than 10kΩ.
Comment
Set to Open state or connect to a high input
impedance node (over 10MΩ).
2
GND
3
PD
4
OS
5
VDD
Power Supply Voltage
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
2/13
TSZ02201-0M2M0F515110-1-2
06.Nov.2015 Rev.001
BDJxxx0HFV Series
Absolute Maximum Ratings
(Ta=25°C)
Parameter
Power Supply Voltage
Input Voltage (PD)
OS Terminal Voltage
OS Terminal Current
Power Dissipation
Storage Temperature Range
Symbol
V
DD
V
IN
V
OS
I
OS
Pd
Tstg
Rating
-0.3 to +7.0
(Note 1)
-0.3 to +V
DD
+0.3
-0.3 to +7.0
(Note 1)
5.0
0.53
(Note 2)
-55 to +150
Unit
V
V
V
mA
W
°C
(Note 1) However, not exceeding Pd.
(Note 2) When mounted on ROHM standard board, derate by 5.36mW/°C for Ta higher than 25°C.
Caution:
Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over
the absolute maximum ratings.
Recommended Operating Conditions
Parameter
Power Supply Voltage
Operating Temperature Range
Symbol
V
DD
Topr
Rating
Min
2.4
-30
Typ
2.8
-
Max
5.5
+100
Unit
V
°C
Electrical Characteristics
(Unless otherwise specified, V
DD
= 2.8V, Ta = 25°C)
Parameter
Supply Current
Normal Function Mode
Power Down Mode
PD
Input L Voltage
Input H Voltage
PD Leakage Current
Analog Output
TEMP Output Voltage
TEMP Temperature Sensitivity
TEMP Load Regulation
TEMP VDD Regulation
OS Output Open Drain
OS Leakage Current
OS Output Voltage
I
L
V
OL
-
-
-
-
1.0
0.4
µA
V
V
OS
=5.0V
I
OS
= 1.0mA
V
TEMP
V
SE
ΔV
TEMPRL
ΔV
TEMPVDD
1.279
-8.00
-
-
1.300
-8.20
-
-
1.321
-8.40
1.0
4.0
V
mV/°C
mV
mV
Ta = 30°C
Ta = -30°C to +100°C
Difference Of
I
OUT
: 0µA / 2µA
V
DD
=2.4V to 5.5V
V
IL
V
IH
I
LPD
GND
1.5
-
-
-
-
0.2
V
DD
1.0
V
V
µA
PD=2.8V
I
DD
I
DDPD
-
-
7.5
0.3
12.0
1.0
µA
µA
PD=“H”
PD=“L”
Symbol
Limit
Min
Typ
Max
Unit
Conditions
Temperature Accuracy
(Unless otherwise specified, V
DD
= 2.8V)
Parameter
Thermostat
Sensing Temperature Accuracy
Sensing Temperature Hysteresis
Analog Output
TEMP Temperature Accuracy
T
TEMP
-
-
±2.5
°C
V
DD
= 2.8V
Ta = -30°C to +100°C
Tacc
Thys
-
7.5
-
10.0
±2.5
12.5
°C
°C
Symbol
Limit
Min
Typ
Max
Unit
Conditions
www.rohm.com
© 2015 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
3/13
TSZ02201-0M2M0F515110-1-2
06.Nov.2015 Rev.001
Talking
京公网安备 11010802033920号
EEWORLD
