Specifications are subject to change without notice.
littelfuse.com
Reed Sensors
Flange Mounting Sensor > 59135
59135 High Temperature Flange Mount Sensor + 57135 Actuator
Electrical Ratings
Contact Type
Switch Type
Contact Rating
Voltage
4
1
Normally
Open
1
VA/Watt - max.
Switching
2
Normally Open
High Voltage
2
10
300
265
400
0.4
0.30
1.4
0.2
10
10
0.2
-20 to +150
Change
Over
3
5
175
120
200
0.25
0.18
1.5
0.2
10
9
0.3
-40 to +150
Normally
Closed
4
5
175
120
200
0.25
0.18
1.5
0.2
10
9
0.3
-40 to +150
10
200
140
250
0.5
0.35
1.2
0.2
10
10
0.3
-40 to +150
Breakdown
4
3
Vdc - max.
Vac - max.
Vdc - min.
Adc - max.
Aac - max.
Adc - max.
Ω - max.
Ω - min.
pF - typ.
°C
Current
Switching
Carry
5
2
Resistance
Contact, Initial
Insulation
Contact
Operating
Capacitance
Temperature
Product Characteristics
Operate Time
Release Time
Shock
7
7
6
6
ms - max.
ms - max.
11ms 1⁄2 sine
50-2000 Hz
G - max.
G - max.
1.0
1.0
100
30
1.0
1.0
100
30
3.0
3.0
50
30
3.0
3.0
50
30
Vibration
Notes:
1. Contact rating - Product of the switching voltage and current should never exceed the wattage rating. Contact Littelfuse for additional load/life information.
2. When switching inductive and/or capacitive loads, the effects of transient voltages and/or currents should be considered. Refer to Application Notes AN108A and AN107 for details.
3. Breakdown Voltage - per MIL-STD-202, Method 301.
4. Electrical Load Life Expectancy - Contact Littelfuse with voltage, current values along with type of load.
5. This resistance value is for 11.81mm wire length. Resistance changes when wire lengthens.
6. Operate (including bounce)/Release Time - per EIA/NARM RS-421-A, diode suppressed coil (Coil II).
7. Shock and Vibration - per EIA/NARM RS-421-A and MIL-STD-202.
8. For custom modifications to the wire length or size, or adding a special connector, please contact Littelfuse.
Sensitivity Options (Using 57135 Actuator)
Select Option
Switch Type
Pull-In AT
Range
S
T
Pull-In AT
Range
U
Activate Distance
mm (inch)
Average
Pull-In AT
Range
V
Activate Distance
mm (inch)
Average
Activate Distance
Activate Distance
Pull-In AT
mm (inch)
mm (inch)
Range
Average
Average
1
2
3
4
Note:
Normally Open
High Voltage
Change Over
Normally Closed
12-18
--
15-20
15-20
18.5 (.729)
--
16.7 (.657)
16.7 (.657)
17-23
17-23
20-25
20-25
17.1 (.673)
17.1 (.673)
14.7 (.579)
14.7 (.579)
22-28
22-28
25-30
25-30
D
15.8 (.622)
15.8 (.622)
13.4 (.528)
13.4 (.528)
27-33
27-33
--
--
15.1 (.595)
15.1 (.595)
--
--
1. Pull-In AT Range: These AT values are the bare reed switch AT before modification.
2. The activation distance is average value on the final sensor assembly
Although HFSS is a very easy-to-use software, it is impossible to use it well if you are not familiar with the basic principles of its processing methods and the basic knowledge of microwaves. The att...
1. The CPU has a built-in supercapacitor to maintain data and always provide power during a power outage that is not too long, and no accessories are required. 2. A battery card is attached to the CPU...
This link: [url=http://www.ti.com.cn/general/cn/docs/gencontent.tsp?contentId=159426]http://www.ti.com.cn/general/cn/docs/gencontent.tsp?contentId=159426[/url] Where is the next discussion?...
I used the HA2556 analog multiplier to square a sine wave. Theoretically, I should get a double-frequency, equal-amplitude, positive half-cycle waveform, but the actual waveform is alternating between...
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
