1. Contact rating - Product of the switching voltage and current should never exceed the wattage rating. Contact Littelfuse for additional load/life information.
2. When switching inductive and/or capacitive loads, the effects of transient voltages and/or currents should be considered. Refer to Application Notes AN108A and AN107 for details.
3. Breakdown Voltage - per MIL-STD-202, Method 301.
4. Electrical Load Life Expectancy - Contact Littelfuse with voltage, current values along with type of load.
5. This resistance value is for 11.81mm wire length. Resistance changes when wire lengthens.
6. Operate (including bounce)/Release Time - per EIA/NARM RS-421-A, diode suppressed coil (Coil II).
7. Shock and Vibration - per EIA/NARM RS-421-A and MIL-STD-202.
8. For custom modifications to the wire length or size, or adding a special connector, please contact Littelfuse.
Sensitivity Options (Using 57020 Actuator)
Select Option
Switch Type
Pull-In AT Range
S
Activate Distance – D
mm (inch)
Average
1
Note:
Normally Open
6-10
6.0 (.236)
1. Pull-In AT Range: These AT values are the bare reed switch AT before modification.
2. The activation distance is average value on the final sensor assembly.
[i=s]This post was last edited by Aguilera on 2019-7-20 17:16[/i]What is PSRR?
PSRR (Power supply rejection ratio), also known as power supply rejection ratio, is an important parameter to measure the...
OK6410 uses VB.NET to control the LED program of ARM11 development board. I am a person who changed from the idea of MCU to ARM. At the beginning, I was not used to the development method of ARM. The ...
The low power consumption feature of MSP430 is well known to everyone, but to bring out the low power consumption feature of 430 actually requires a good power supply solution.If the power supply sche...
The program is as follows, which is the IIC master communication program: #include
unsigned char TXData =0;// Pointer to TX data
unsigned char TXByteCtr;
int main(void)
{WDTCTL = WDTPW + WDTHOLD;// In...
Designing for automotive LCD displays larger than 5" can be complex. The display source driver requires a supply rail called analog voltage device drain (AVDD) in the 10V to 15V range and two supply ...[Details]
In order to strengthen the management of new energy vehicle charging facilities in our city, prevent and reduce accidents, protect the lives and property of the people, and improve the public safet...[Details]
Recently, the US embargo on ZTE has attracted much attention. Let's take a look at the relevant content with the automotive electronics editor. On April 16, local time, the U.S. Department of Co...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
1. About FPU transplantation As long as the chip has FPU function, the use of FPU is generally enabled by default. You can also select it in the Options tab; 2. About the transplantation of DSP li...[Details]
1. FSMC Brief FSMC, the Flexible Static Storage Controller, is capable of interfacing with synchronous or asynchronous memories and 16-bit PC memory cards. The FSMC interface of STM32 s...[Details]
According to TechRadar, given rumors that
Google
is developing a Pixel Watch
,
the
recently renamed Wear OS
smartwatch
operating system may soon be able to show its full cap...[Details]
At this exhibition, Microsoft brought its flagship intelligent voice products - XiaoIce and Xiaona. In addition, the voice will be equipped with an intelligent face recognition system. Let's see ho...[Details]
The storage media corresponding to the three boot modes of STM32 are built-in to the chip, they are: 1. User Flash = Flash built into the chip 2.SRAM = RAM area built into the chip, which is the m...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
When the program starts running, light A turns on for 5 seconds, then turns off, light B turns on for 5 seconds, light B turns off, light C turns on for 5 seconds, light C turns off, the program ends...[Details]
Timer Interrupt The timer function of STM32 is very powerful. There are advanced timers such as TIME1 and TIME8, general timers such as TIME2~TIME5, and basic timers such as TIME6 and TIME7. In th...[Details]
Mixed reality (augmented and virtual reality) is the next computing frontier after the PC in the 1970s, the web in the 1990s, and mobile platforms in the 21st century.
MR
is the most unique...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
