Daniels Manufacturing Corporation offers complete refurbishing and recalibration services.
DMC specially engineers and manufactures complete tool kits to satisfy individual
customer requirements, such as total aircraft support, general shop maintenance
or production, on board ship and vehicle service, etc.
LIMITATION OF LIABILITY
DANIELS MANUFACTURING CORPORATION IS NOT LIABLE FOR
CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY NATURE OR KIND RESULTING
FROM THE USE, OR MISUSE, OF ANY OF ITS PRODUCTS. OWNERS AND
USERS OF DMC PRODUCTS ASSUME FULL RESPONSIBILITY FOR INSTRUCTING
THEIR EMPLOYEES IN THE PROPER AND SAFE USE OF SUCH PRODUCTS.
LIMITED WARRANTY
DMC (Daniels Manufacturing Corporation) worronts each new product
sold by it to be free from defects in material and workmanship under normal
use and service. DMC's obligation under this warranty is limited to the free
correction or, at DMC's option, the refund of the purchase price of ony such
product which proves defective in normal service within ninety (90) days after
delivery to the first user, provided that the product is returned to DMC with oil
transportation charges prepaid and which shall oppeor to DMC's satisfaction,
ofter DMC's inspection, to have been defective in material or workmanship,
it being understood that DMC products ore not consumer products. This
warranty shall not cover any damage to any product which, in the opinion of
DMC, was caused by normal wear, misuse, improper operation, tampering,
neglect or accident. This warranty is in lieu of all other warranties express
or implied. No warranty, express or implied, is mode or authorized to be made
or assumed with respect to products of Daniels Manufacturing Corporation other
than those herein set forth.
86-37 UNIVERSAL POSITIONER
The 86-37 Universal Positioner is used
with the MH860 crimp tools to locate
contacts horizontally and vertically between
the indenters of the tools.
SEE REVERSE SIDE F
O
R IMP
O
RTA
N
T INF
O
RMATIO
N
C
O
NCERNING
LIM
I
TED WARRANTY, AND LIMITAT
IO
N OF LIAB
I
LITY.
ADJUSTME
N
T
}
SCREW
DATASHEET
,,,..411A
DANIELS
TOP OF
WIRE BARRE L
MANUFACTURING
w1
-...,
CORPORATION
DANIELS MANUFACTUR
I
NG C
O
RP., 526 TH
O
RPE R
O
AD, ORLANDO, FL 32824, USA, PHONE 407/855-6161, FAX 407/855-6884
COPYR
I
GHT© 2002 DA
NI
ELS MA
N
UFACTURING C
O
RP., USA.
ALL RIGHTS RESERVED.
WWW.DMCTOOLS.C
O
M E-MAIL: DMCOOMCTO
O
LS.COM
2/02
REV. B
1. Align the bayonet pins of the positianer with the
86-37 P
O
S
I
TI
O
NER
slots in the crimp tool. Insert and push positioner
CRIMP TOOL
against the spring, then rotate the positioner 90'
so that the bayonet pins fall into the internal slots
of the tool. The positioner is now secured to the tool frame.
2. Raise and rotate the selector knob to the desired setting.
3. Screw the jam nut away from the positioner body and turn the adjustment screw clockwise to its highest setting.
4. Insert the contact to be crimped, into the locator. The contact should now be sitting too high into the tool. Turn the
adjustment screw counterclockwise to move the contact lower into the crimp tool, until the indenters of the tool are
estimated to be centered between the inspection hole and the top of the wire barrel. If the contact is designed with an
insulation cup, adjust the vertical location of the contact so that the indenters are centered between the inspection hole
and the bottom of the insulation cup.
5. When the ideal positioner adjustment is achieved for the contact, tighten the jam nut against the positioner body in
order to lock the adjustment screw in place. The tool and positioner assembly is now ready for crimping the designated
contact.
86-37-DS
INSTRUCTIONS
CAUTION: Before installing or removing the
positioner from the crimp tool, be sure the
adjustment screw is at least one complete
turn outward from the inner limit of adjust
ment (turn the adjustment screw counter
clockwise for at least one full rotation).
POSITIO
N
ER BODY
JAM NUT
/l
'frr,
BAYONET PI
N
/
SPECTION
HOLE
i
r
ION
lNSU½t
½
0
CONTACTS
86-37 UNIVERSAL POSITIONER
The 86-37 Universal Positioner is used
with the MH860 crimp tools to locate
contacts horizontally and vertically between
the indenters of the tools.
INSTRUCTIONS
SEE REVERSE SIDE FOR IMPORTANT INFORMATION CONCERNING
LIMITED WARRANTY, AND LIMITATION OF LIABILITY.
ADJUSTMENT}
SCREW
J
fl(,
DATASHEET
TOP OF
WIRE BARREL
,,,..aADANIELS
MANUFACTURING
_.,
-..,
CORPORATION
2. Raise and rotate the selector knob ta the desired setting.
3. Screw the jam nut away from the positioner body ond turn the adjustment screw clockwise to its highest setting.
4. Insert the contact to be crimped, into the locator. The contact should now be sitting too high into the tool. Turn the
adjustment screw counterclockwise to move the contact lower into the crimp tool, until the indenters of the tool are
estimated to be centered between the inspection hole and the top of the wire barrel. If the contact is designed with an
insulation cup, adjust the vertical location of the contact so that the indenters are centered between the inspection hole
and the bottom of the insulation cup.
5. When the ideal positioner adjustment is achieved for the contact, tighten the jam nut against the positioner body in
order to lock the adjustment screw in place. The tool and positioner assembly is now ready for crimping the designated
contact.
DANIELS MANUFACTURING CORP., 526 THORPE ROAD, ORLANDO, FL 32824, USA, PHONE 407/855-6161, FAX 407 /855-6884
ALL RIGHTS RESERVED.
WWW.DMCTOOLS.COM E-MAIL: DMCOOMCTOOLS.COM
COPYRIGHT© 2002 DANIELS MANUFACTURING CORP., USA.
2/02
REY. B
86-37-DS
Daniels Manufacturing Corporation offers complete refurbishing and recalibration services.
DMC specially engineers and manufactures complete tool kits to satisfy individual
1. Align the bayonet pins of the positioner with the
86-37 POSITIONER
slots in the crimp tool. Insert and push positioner
against the spring, then rotate the positioner 90'
so that the bayonet pins fall into the internal slots
of the tool. The positioner is now secured to the tool frame.
CAUTION: Before installing or removing the
positioner from the crimp tool, be sure the
adjustment screw is at least one complete
turn outward from the inner limit of adjust
ment (turn the adjustment screw counter
clockwise for at least one full rotation).
POSITIONER BODY
JAM NUT
SPECTION
HOLE
i
t
CONTACTS
lNSU½e TION
0
BAYONET PIN
/
SELECTOR
½C½R=IM½P½"-"'"
customer requirements, such as total aircraft support, general shop maintenance
or production, on board ship and vehicle service, etc.
LIMITATION OF LIABILITY
DANIELS MANUFACTURING CORPORATION IS NOT LIABLE FOR
CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY NATURE OR KIND RESULTING
FROM THE USE, OR MISUSE, OF ANY OF ITS PRODUCTS. OWNERS AND
USERS OF DMC PRODUCTS ASSUME FULL RESPONSIBILITY FOR INSTRUCTING
THEIR EMPLOYEES IN THE PROPER AND SAFE USE OF SUCH PRODUCTS.
LIMITED WARRANTY
DMC (Daniels Manufacturing Corporation) warrants each new product
sold by it to be free from defects in material and workmanship under normal
use and service. DMC's obligation under this warranty is limited to the free
correction or, at DMC's option, the refund of the purchase price of any such
product which proves defective in normol service within ninety (90) days after
delivery to the first user, provided that the product is returned to DMC with all
transportation charges prepaid and which shall appear to DMC's satisfaction,
ofter DMC's inspection, to hove been defective in material or workmanship,
it being understood that DMC products ore not consumer products. This
warranty shall not cover any damage to any product which, in the opinion of
DMC, was caused by normal wear, misuse, improper operation, tampering,
neglect or occident. This warranty is in lieu of all other warranties express
or implied. No warranty, express or implied, is mode or authorized to be mode
or assumed with respect to products of Daniels Manufacturing Corporation other
than those herein set forth.
京公网安备 11010802033920号
EEWORLD
