Product Data Sheet
Product Data Sheet
3M
™
Metal-Out Static Shielding Bag 2100R/2110R
The transparent, puncture resistant metal-out static shielding bag is designed to
provide a static safe environment for sensitive electronic devices. The metal layer is
positioned near the outer surface to help reduce voltage retention and enhance static
decay. Bags are printed with and ESD warning symbol and a lot code for traceability.
Open Top (2100R) and ZipTop (2110R) styles are available. The bags are heat sealable.
3M Static Shielding Bags are manufactured from a top coat, metal, polyester,
polyethylene laminate. The proprietary top coating is designed to protect the metal
layer. Polyester dielectric, in concert with the metal layer, is intended to provide
shielding of Electrostatic Discharge (ESD) and to help minimize the penetration of
electric field.
The bags are tested to meet or exceed certain electrical and physical requirements
of ANSI/ESD S541 and to be ANSI/ESD S20.20 program compliant. Bags are RoHS
Compliant* and lead-free**.
Physical
Typical Value
8000 PSI, 55 MPa
24 lbs, 106 N
18 lbs, 80 N
3.2 mils, .081 mm +/-15%
Pass
Testing Method
Tensile Strength
Puncture Resistance
Seal Strength
Thickness
Marking Adhesion
Transparency
Electrical
ESD Shielding
ASTM D882
MIL-STD-3010C Method 2065
ASTM D882
MIL-STD-3010C Method 1003
IPC-TM-650 2.4.1
Tobias
Testing Method
ANSI/ESD STM11.31
37%
Typical Value
<10 nJ
<1x10
11
ohms
<1x10
6
ohms
Surface Resistance -
Interior
Surface Resistance -
Exterior
Static Decay
ANSI/ESD STM11.11
ANSI/ESD STM11.11
ETS 406D
CPM – 3M TP.21XX
Testing Method
FTIR
< 2 seconds
<100 volts
Typical Value
Not Detected
Typical Value
375°F, 190°C
0.5 – 3.5 seconds
30 – 70 PSI, 206 – 482 KPa
3M
™
Metal-Out Static Shielding Bag
2100R/2110R
Charge Retention
Cleanliness
Silicone
Heat Sealing Conditions
Temperature
Time
Pressure
This product is intended for commercial use only. This product is not on the Qualified
Product Listing under the Defense Standardization Program.
Product Data Sheet
Open
Open
Bag
Bag
Top
Top
ZipTop Bag
ZipTop Bag
3M
™
Metal-Out Static Shielding Bag 2100R/2110R
Metal-Out Static Shielding Bags 2100R, Open Top
Dimensions
(W x L in.)
3x5
Part No.
21035
21044
21046
210426
Dimensions
(W x L in.)
Part No.
Dimensions
(W x L in.)
Part No.
8 x 10
8 x 12
10 x 12
10 x 14
11 x 15
12 x 16
12 x 18
14 x 18
21810
210812
2101012
2101014
2101115
2101216
2101218
2101418
15 x 18
16 x 24
18 x 18
18 x 24
24 x 24
24 x 30
24 x 36
2101518
2101624
2101818
2101824
2102424
2102430
2102436
• Standard sizes
(inches): Width
shipment (usually same
+/- 0.125
Tolerance (inches): Width -0, +0.250
Tolerance
stocked for prompt
-0, +0.250 Length
Offset 0 to 0.250
day).
width +/- 0.125
Length +/- 0.125 Offset 0 to 0.250
Seal
• Width is measured from inside seam to inside seam.
Seal width +/- 0.125
• Length is measured from the top edge to the bottom fold.
• Opening is in the “width” dimension.
• Custom bag sizes, custom printing, and custom hot stamping
are available.
• Most sizes are packed 100 per case.
• Small sizes are packed 500 or 1,000 per case.
3M is a trademark of 3M Company. All other trademarks are owned by their respective companies.
4x4
4x6
4 x 26
5x8
6x8
6 x 10
8x8
21058
21068
210610
21088
Metal-Out Static Shielding Bags 2110R, ZipTop
Dimensions
(W x L in.)
3x5
Part No.
21135
Dimensions
(W x L in.)
Part No.
Dimensions
(W x L in.)
Part No.
6x8
6 x 10
8 x 10
8 x 12
10 x 12
21168
211610
211810
211812
2111012
10 x 14
10 x 26
11 x 15
18 x 24
2111014
2111026
2111115
2111824
4x4
4x6
4 x 26
5x8
21144
21146
211426
21158
*
RoHS 2011/65/EU Compliant
means that the product or pa rt does not contain any of the substances in excess of the maximum
concentration values (“MCVs”) in EU RoHS Directive 2011/65/EU. The MCVs are by weight in homogeneous materials. This
information represents 3M’s knowledge and belief, which may be based in whole or in part on information provided by third party
suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information, then 3M’s entire liability and Buyer’s exclusive
remedy will be in accordance with the Warranty section.
**Lead-free means that the product has less than 2 ppm of lead when tested by ICP-AES, with reference to EPA method
3051A/3052.
Important Notice
All statements, technical information, and recommendations related to 3M’s products
are based on information believed to be reliable, but the accuracy or completeness is not
guaranteed. Before using this product, you must evaluate it and determine if it is suitable for
your intended application. You assume all risks and liability associated with such use. Any
statements related to the product which are not contained in 3M’s current publications, or
any contrary statements contained on your purchase order shall have no force or effect unless
expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for one year from the
time of purchase.
3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT
LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
If this product is defective within the warranty period
stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M
product or refund the purchase price of the 3M product. Except where prohibited by law, 3M
will not be liable for any indirect, special, incidental or consequential loss or damage arising
from this 3M product, regardless of the legal theory asserted.
3
Electronic Solutions Division
Static Control Products
926 JR Industrial Drive
Sanford, NC 27332-9733
Toll-Free: 866-722-3736
International: 919-718-0000
Email: 3mstaticinfo@mmm.com
www.3Mstatic.com
Please recycle. Printed in USA.
© 3M 2013. All rights reserved.
98-0799-1142-0 JHA