NB: B4 is the shortest “last make, first break” sequenced signal pin
Blade Assignment
Function
Description
PB1, PB2, PB3
+12V GND
Main Output Voltage, Return
PB4, PB5, PB6
+12V OUT
Main Output Voltage
Signal Pin Assignment
Signal Name
Description
An input pulled up via an internal 10K ohm to the Standby rail. When pulled low (via an open collector/drain
A1
PS_ON_L
drive or connection to GND) the Main Output will be turned on/enabled)
A2
+12VRS_RETURN Main Output Remote Sense (-VE/Return)
A3
TEMP_OK
TTL compatible Logic HIGH provided when the temperature is within the allowable range of operation.
Internally connected to GND; when the power module is correctly seated the corresponding mating
A4
PS_SEATED
connector pin is grounded and therefore allows detection that the power module is in situ.
A5, B5, C5, D5
+VSB
Standby Voltage Output
A6, B6, C6, D6
+VSB GND
Standby Voltage Output, Return/GND
B1
AC_OK
Incoming AC Source voltage “OK” (present and within operational limits)
B2
+12VRS
Main 12V output remote sense line
B3
+12V_ISHARE
Main 12V output current share bus
B4
C1
C2
This is the shortest “last make, first break” (last to mate in the sequence).
If left open circuit then the main output will be inhibited (no output).
PS_INHIBIT/PS_KILL
When inserted in to the system slot this pin must be pulled “low” by the system to enable (turn on) the
Main output and only after all other pins are connected and the power module is correctly seated.
SDA
SCL
I
2
C Serial Data Line
I
2
C Serial Clock Line
Current (Amps per Pin)
30
30
N/A
N/A
N/A
2.0
2.0
N/A
N/A
N/A
N/A
N/A
N/A
www.murata-ps.com/support
D1U3CS-W-1300F-12-Hx4EC.A01
Page 3 of 5
D1U3CS-W-1300F-12-Hx4EC Series
81mm Front End AC-DC Power Converter
Signal Pin Assignment
C3
C4
D1
D2
D3
D4
MATING CONNECTOR
Supplier
FCI
Signal Name
PWR_GD
FAN_FAIL
A0
A1
S_INT
N/A
Description
Power Good signal. An active TTL HIGH signifies when the output is within regulation limits.
Fan Fail signal (failure or locked rotor)
I
2
C LSB (Least Significant Bit) Address Line
I
2
C MSB (Most Significant Bit) Address Line
System Interrupt
Reserved; no end user connection
Press Fit, Straight
---
Press Fit, Right Angle
51761-10002406AA
Solder Straight
---
Current (Amps per Pin)
N/A
N/A
N/A
N/A
N/A
N/A
Solder Right Angle
---
WIRING DIAGRAM FOR OUTPUT
Dotted lines show optional remote sense connections.
Optional remote sense lines can be attached to a load that is a distance
away from the power supply to improve regulation at the load.
+12VRS (Main Output Remote Sense)
+12V OUT
+12VRS (Main Output Remote Sense)
+12V OUT
B2
PB4-6
PB4-6
B2
D1U3CS
PB1-3
+12V GND
+12VRS_RETURN
+12V_ISHARE
12V load
+12V GND
+12VRS_RETURN
+12V_ISHARE
PB1-3
A2
B3
D1U3CS
A2
B3
A5,B5,C5,D5
A1
+VSB
PS_ON_L
+VSB load
FET, BJT, wire
or switch (debounced )
to turn on +12V main output
+VSB
PS_ON_L
A5,B5,C5,D5
A1
A6,B6,C6,D6
+VSB GND
+VSB GND A6,B6,C6,D6
B4
PS_INHIBIT/PS_KILL
PS_INHIBIT/PS_KILL
B4
CURRENT SHARING NOTES
1. Main 12VDC Output: Analogue active share bus. The ISHARE bus (Pin B3) must be connected on all sharing modules. It is not required that the SENSE signals are connected to the remote load for current share
to operate correctly.
2. Up to eight (8) power modules can be connected in parallel (non-redundant) or N+1 configuration. The current share bus is analogue bi-directional (can source or sink current from the ISHARE bus). The voltage
of the bus would measure 8VDC for a single power module at 100% load; for two (2) modules sharing a common load the ISHARE bus voltage would be 4V for a perfect 50/50 current share scenario.
3. VSTANDBY output power modules can also be connected in parallel and have internal output isolation devices; however the combined available power is limited to that available from a single power module
(3.3V or 5V; 20W) irrespective of the number of modules connected in parallel.
www.murata-ps.com/support
D1U3CS-W-1300F-12-Hx4EC.A01
Page 4 of 5
D1U3CS-W-1300F-12-Hx4EC Series
81mm Front End AC-DC Power Converter
MECHANICAL DIMENSIONS
Direction of Airflow
AC Input Connector/Inlet: IEC 60320-C14
Dimensions: 3.20" x 11.00" x 1.57" [81.3mm x 279.4mm x 39.9mm]
OPTIONAL ACCESSORIES
Description
D1U3CS-12 Output Interface Connector Card
APPLICATION NOTES
Document Number
ACAN-41
ACAN-49
Part Number
D1U3CS-12-CONC
Description
D1U3CS-12-CONC Output Interface Connector Card
D1U3CS-12 Communications Protocol
Link
www.murata-ps.com/data/apnotes/acan-41.pdf
www.murata-ps.com/data/apnotes/acan-49.pdf
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
ISO 9001 and 14001 REGISTERED
This product is subject to the following operating requirements
and the Life and Safety Critical Application Sales Policy:
Refer to:
http://www.murata-ps.com/requirements/
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
The essay writing competition is halfway through. Thank you all for participating in the event. You have shared your wonderful 51 learning experiences. Some of the words you shared are classics of the...
I would like to ask you, why is (TH*256+TL)*0.0625 the integer part, and why is the decimal part (TL%16)*10*0.0625? Why don't we use decimals? When calculating the temperature, the temperature is equa...
1) It is very simple to apply for a space. You only need to use your username and password in the forum. If you already have a forum username, just fill it in and enter. 24077 2) If you do not have a ...
;------------------------------------------- ;Crossroad traffic light controller;MADE BY Leo ;------------------------------------------- ;Use the single-chip P1.0-P1.5 ports to control the straight/l...
Abstract: This paper discusses the circuit structure and basic principle of power factor correction circuit that must be possessed by high-performance electronic ballast system, and introduces the ele...
A line scan lens is an industrial lens used with line scan cameras. Its imaging principle is to capture the image of the workpiece using a linear sensor and then perform digital signal processing t...[Details]
As more and more consumers purchase new energy vehicles, the safety of electric vehicles has become a major concern. This has been particularly prominent following a series of electric vehicle fire...[Details]
As the number of cars increases, environmental pressures are also increasing. At this time, some people are saying that new energy vehicles are energy-efficient and environmentally friendly, and ar...[Details]
On August 22nd, Lantu Motors unveiled a new technology called "Lanhai Intelligent Hybrid" during a live broadcast of CCTV News' "Top Laboratory." The name sounds like another new term, but a closer...[Details]
On August 20th, Tiantai Robotics Co., Ltd., along with strategic partners including Shandong Future Robotics Technology Co., Ltd., Shandong Future Data Technology Co., Ltd., and Gangzai Robotics Gr...[Details]
Electric vehicles are now widespread, but they've brought with them a host of problems, the most prominent of which is charging. Small electric vehicles (EVs) are a new form of transportation in a ...[Details]
Laird Thermal Systems has introduced the HiTemp ET series Peltier cooler modules, which can operate at high temperatures and provide on-site cooling for sensitive electronic devices.
Dig...[Details]
UPS stands for Uninterruptible Power Supply, which includes energy storage devices. It is mainly used to provide uninterruptible power supply for devices that require high power stability.
...[Details]
SMT placement machines are important equipment in surface mount technology (Surface Mount Technology). Their performance has a decisive impact on the quality and efficiency of electronic manufactur...[Details]
A human-machine interface (HMI) refers to the platform used by people to operate a PLC. This platform provides an interface between programs and humans, serving as a medium for information transmis...[Details]
Reflow soldering, as an electronics assembly process, has become a vital component of the electronics manufacturing industry. Choosing reflow soldering equipment is crucial for improving production...[Details]
In the field of intelligent driving, regulations are becoming increasingly stringent, and the technical threshold continues to rise. Especially after the traffic accident in March 2025, the Ministr...[Details]
In daily life, when we purchase a transformer, we are faced with the installation and wiring procedures. Generally speaking, large transformers such as power transformers are equipped with speciali...[Details]
Charging is an essential topic for electric vehicles. Batteries are a core component of new energy vehicles. So, what's the optimal charge level for electric vehicles? Based on current battery tech...[Details]
introduction
A common voltage regulator is a three-terminal one. Its function is to step down the voltage and stabilize it at a fixed output value. Voltage regulators are commonly available in...[Details]
51mcu
京公网安备 11010802033920号
EEWORLD
