January 2005
rev 1.5
ASM1232LP/LPS
5V µP Power Supply Monitor and Reset Circuit
•
•
Low-cost surface mount packages: 8-pin/16-pin SO, 8-pin
DIP and 8-pin Micro SO packages
Wide operating temperature -40°C to +85°C (N suffixed
devices)
General Description
The ASM1232LP/LPS is a fully integrated microprocessor
supervisor. It can halt and restart a “hung-up” microprocessor,
restart a microprocessor after a power failure. It has a
watchdog timer and external reset override.
A
precision
temperature-compensated
reference
and
Applications
•
•
•
•
•
•
Microprocessor Systems
Computers
Controllers
Portable Equipment
Intelligent Instuments
Automotive Systems
comparator circuits monitor the 5V, V
CC
input voltage status.
During power-up or when the V
CC
power supply falls outside
selectable tolerance limits, both RESET and RESET become
active. When V
CC
rises above the threshold voltage, the reset
signals remain active for an additional 250ms minimum,
allowing the power supply and system microprocessor to
stabilize. The trip point tolerance signal, TOL, selects the trip
level tolerance to be either 5% or 10%.
Each device has both a push-pull, active HIGH reset output
and an open drain active LOW reset output. A debounced
manual reset input, PBRST, activates the reset outputs for a
minimum period of 250ms.
There is a watchdog timer to stop and restart a microprocessor
that is “hung-up”. The watchdog timeouts periods are
selectable: 150ms, 610ms and 1200ms. If the ST input is not
strobed LOW before the time-out period expires, a reset is
generated.
Devices are available in 8-pin DIP, 16-pin SO and compact 8-
pin MicroSO packages.
Typical Operating Circuit
+5V
ASM1232LP/LPS
ST
RESET
GND
TD
TOL
10kΩ
I/O
µP
RESET
Block Diagram
ASM1232LP/LPS
V
CC
TOL
Tolerance Selection
+
Reference
V
CC
40kΩ
Key Features
•
•
•
•
•
•
•
•
5V supply monitor
Selectable watchdog period
Debounce manual push-button reset input
Precision temperature-compensated voltage reference
and comparator.
Power-up, power-down and brown out detection
250ms minimum reset time
Active LOW open drain reset output and active HIGH
push-pull output
Selectable trip point tolerance: 5% or 10%
RESET
-
RESET
PBRST
TD
Push Button
Debounce
Voltage Sense
Comparators
Watchdog Transition
Detector
Reset &
Watchdog Timer
ST
GND
Alliance Semiconductor
2575 Augustine Drive . Santa Clara, CA 95054 . Tel: 408.855.4900 . Fax: 408.855.4999 . www.alsc.com
Notice: The information in this document is subject to change without notice
January 2005
rev 1.5
ASM1232LP/LPS
Pin Configuration
DIP/SO/MicroSO
PBRST
TD
TOL
GND
1
2
3
4
ASM1232LP
ASM1232LPS-2
ASM1232LPU
8
7
6
5
V
CC
ST
RESET
RESET
NC
1
SO
16 NC
15 V
CC
14
NC
ST
NC
RESET
NC
RESET
PBRST 2
NC
TD
NC
TOL
NC
GND
3
4
5
6
7
8
ASM1232LPS
13
12
11
10
9
Pin Description
Pin #
8-Pin Package
1
2
Pin #
16-Pin Package
2
4
Pin
Name
PBRST
TD
Function
Debounced manual pushbutton RESET input.
Watchdog time delay selection. (t
TD
= 150ms for TD = GND, t
TD
= 610ms
for TD=Open, and t
TD
= 1200ms for TD = V
CC
).
Selects 5% (TOL connected to GND) or 10% (TOL connected to V
CC
)
trip point tolerance.
Ground.
Active HIGH reset output. RESET is active:
1. If V
CC
falls below the reset voltage trip point.
5
9
RESET
2. If PBRST is LOW.
3. If ST is not strobed LOW before the timeout period set by TD expires.
4. During power-up.
Active LOW reset output. (See RESET).
Strobe input.
5V power.
No internal connection.
3
4
6
8
TOL
GND
6
7
8
-
11
13
15
1,3,5,7,
10,12,14,16
RESET
ST
V
CC
NC
5V µP Power Supply Monitor and Reset Circuit
Notice: The information in this document is subject to change without notice
2 of 10
January 2005
rev 1.5
ASM1232LP/LPS
Detailed Description
The ASM1232LP/LPS monitors the microprocessor or
microcontroller power supply and generates reset signal,
both active HIGH and Active LOW, that halt processor
operation whenever the power supply voltage levels are
outside a predetermined tolerance.
V
CC
V
CCTP
(MIN)
t
R
V
CCTP
(MAX)
V
CCTP
t
RPU
RESET
V
OH
~
~
RESET and RESET outputs
RESET is an active HIGH signal developed by a CMOS
push-pull output stage and is the logical opposite to RESET.
V
OL
RESET
~
~
~~
RESET is an active LOW signal. It is developed with an open
drain driver. A pull up resistor of typical value 10kΩ to 50kΩ is
required to connect with the output.
Figure 1: Timing Diagram : Power Up
Trip Point Tolerance Selection
The TOL input is used to determine the level V
CC
can vary
below 5V without asserting a reset. With TOL conected to
V
CC
, RESET and RESET become active whenever V
CC
falls
below 4.5V. RESET and RESET become active when the
V
CC
falls below 4.75V if TOL is connected to ground.
After V
CC
has risen above the trip point set by TOL, RESET
and RESET remain active for a minimum time period of
250ms. On power-down, once V
CC
falls below the reset
threshold RESET stays LOW and is guaranteed to be 0.4V or
less until V
CC
drops below 1.2V. The active HIGH reset signal
is valid down to a V
CC
level of 1.2V also.
RESET
V
OH
RESET
t
RPD
V
CC
V
CCTP
(MAX)
V
CCTP
V
CCTP
(MIN)
t
F
Figure 2: Timing Diagram : Power Down
Tolerance
Select
TOL = V
CC
TOL = GND
Tolerance
TRIP Point Voltage
(V)
Min
Nom
4.37
4.62
Max
4.49
4.74
Application Information
Manual Reset Operation
Push-button switch input, PBRST, allows the user to override
the internal trip point detection circuits and issue reset
signals. The pushbutton input is debounced and is pulled
HIGH through an internal 40kΩ resistor.
10%
5%
4.25
4.5
~~
~
V
OL
~~
5V µP Power Supply Monitor and Reset Circuit
Notice: The information in this document is subject to change without notice
3 of 10
January 2005
rev 1.5
When PBRST is held LOW for the minimum time t
PB
, both
resets become active and remain active for a minimum time
period of 250ms after PBRST returns HIGH.
The debounced input is guaranteed to recognize pulses
greater than 20ms. No external pull-up resistor is required,
since PBRST is pulled HIGH by an internal 40kΩ resistor.
ST
ASM1232LP/LPS
power-up after the supply voltage returns to an in-tolerance
condition, the reset signal remains active for 250ms
minimum,
be detected.
Valid
Strobe
Valid
Strobe
Invalid
Strobe
allowing
the
power
supply
and
system
microprocessor to stabilize. ST pulses as short as 20ns can
The PBRST can be driven from a TTL or CMOS logic line or
shorted to ground with a mechanical switch.
t
PB
t
PDLY
V
IL
V
IH
RESET
t
ST
t
RST
t
TD
(min)
t
TD
(max)
~
~
PBRST
Note: ST is ignored whenever a reset is active
Figure 5: Timing Diagram: Strobe Input
Timeouts periods of approximately 150ms, 610ms or
1,200ms are selected through the TD pin.
V
OH
V
OL
~
~
t
RST
RESET
RESET
Figure 3: Timing Diagram: Pushbutton Reset
ASM1232LP/LPS
1
2
3
4
PBRST
TD
TOL
GND
V
CC
8
ST
RESET
RESET
Figure 4: Application Circuit: Pushbutton Reset
Watchdog Timer and ST Input
A watchdog timer stops and restarts a microprocessor that is
“hung-up”. The µP must toggle the ST input within a set
period (as selectable through TD input) to verify proper
software execution. If the ST is not toggled low within the
minimum timeout period, reset signals become active. In
~~
~~
5V
7
6
5
I/O
TD Voltage level
Watchdog Time-out Period
(ms)
Min
Nom
150
610
1200
Max
250
1000
2000
GND
Floating
V
CC
62.5
250
500
The watchdog timer can not be disabled. It must be strobed
µP
RESET
5V
with a high-to-low transition to avoid watchdog timeout and
reset.
ASM1232 LP/LPS
1
2
3
4
PBRST
T
D
TOL
GND
V
CC
8
ST
RESET
MREQ
10kΩ
7
6
5
µP
RESET
Address
Bus
Decoder
Figure 6: Application Circuit: Watchdog Timer
5V µP Power Supply Monitor and Reset Circuit
Notice: The information in this document is subject to change without notice
4 of 10
January 2005
rev 1.5
ASM1232LP/LPS
Absolute Maximum Ratings
Parameter
Voltage on V
CC
Voltage on ST, TD
Voltage on PBRST, RESET, RESET
Operating Temperature Range (N suffixed devices)
Operating Temperature Range (others)
Soldering Temperature (for 10 sec)
Storage Temperature
ESD rating
HBM
MM
Min
-0.5
-0.5
-0.5
-40
0
Max
7
V
CC
+ 0.5
V
CC
+ 0.5
+85
70
+260
Unit
V
V
V
°C
°C
°C
°C
KV
V
-55
+125
2
200
Note:
1. Voltages are measured with respect to ground
2. These are stress ratings only and functional implication is not implied. Exposure to absolute maximum ratings for extended
periods may affect device reliability.
DC Electrical Characteristics
Unless otherwise stated, 4.5V <= V
CC
<= 5.5V and over the operating temperature range of 0°C to 70°C (-40°C to +85°C. for N devices). All
voltages are referenced to ground.
Parameter
Supply Voltage
ST and PBRST Input High Level
ST and PBRST Input Low Level
V
CC
Trip Point (T
OL
= GND)
V
CC
Trip Point (T
OL
= V
CC
)
Watchdog Timeout Period
Watchdog Timeout Period
Watchdog Timeout Period
Output Voltage
Output Current
Output Current
Symbol
V
CC
V
IH
V
IL
V
CCTP
V
CCTP
t
TD
t
TD
t
TD
V
OH
I
OH
I
OL
Conditions
Min
4.5
2
-0.3
4.50
4.25
Typ
Max
5.5
V
CC
+ 0.3
0.8
Unit
V
V
V
V
V
ms
ms
ms
V
mA
mA
5 of 10
4.62
4.37
150
1200
610
V
CC
- 0.1
-10
4.74
4.49
250
2000
1000
T
D
= GND
T
D
= VCC
T
D
Floating
I=-500µA, Note 3
Output = 2.4V, Note 2
Output = 0.4V
62.5
500
250
V
CC
- 0.5
-8
10
5V µP Power Supply Monitor and Reset Circuit
Notice: The information in this document is subject to change without notice
MCU
京公网安备 11010802033920号
EEWORLD
