L: output is low level (weak pull down) oscillation stops
SiTime Corporation
Rev. 1.04
990 Almanor Avenue, Suite 200
Sunnyvale, CA 94085
(408) 328-4400
www.sitime.com
Revised Sept. 19, 2008
SiT8002
Description
The SiT8002 oscillator family is composed of the world’s
smallest, high-performance programmable oscillators. The
SiT8002 is suitable for use in clock generation for consumer,
portable, industrial, automotive, and computation applications.
This oscillator family is packaged in standard low-cost plastic
QFN-type IC packages with footprints that match common
quartz surface mount products.
MEMS resonators are 1000x smaller by volume than quartz
resonators and are built in high volume CMOS fabs instead of
small custom manufacturing facilities. Due to their small size,
massive lot sizes, and simpler manufacturing processes
MEMS oscillators are inherently more reliable, have more
consistent performance and are always in stock.
The SiT8002, by eliminating the quartz crystals, has improved
immunity to the environmental effects of vibration, shock,
strain, and humidity.
To order samples, go to www.sitime.com and click on Request
Sample” link.
Absolute Maximum Ratings
Attempted operation outside the absolute maximum ratings of the part may cause permanent damage to the part. Actual
performance of the IC is only guaranteed within the operational specifications not absolute maximum ratings.
Ab
solute Maximum Table
Parameter
Storage Temperature
VDD
Electrostatic Discharge
Theta JA ( with copper plane on VDD and GND)
Theta JC (with PCB traces of 0.010 inch to all pins)
Soldering Temperature (follow standard Pb free soldering guidelines)
Number of Program Writes
Program Retention over -40 to 125C, Process, VDD (0 to 3.6V)
–
–
Min.
-65
-0.5
Max.
150
+3.65
6000
75
24
260
1
1,000+
Unit
°C
V
V
°C/W
°C/W
°C
NA
years
Operating Conditions
Parameter
Supply Voltages, VDD
[1]
Min.
2.97
2.25
1.7
Typ.
3.3
2.5
1.8
-
-
-
-
Max.
3.63
2.75
1.9
70
85
15
200
Unit
V
V
V
°C
°C
pF
ms
Extended Commercial OperatingTemperature
Industrial Operating Temperature
Maximum Load
Capacitance
[2]
VDD Ramp Time
-20
-40
-
0
Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensibility Level
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Notes:
1. The 2.5V device can operate from 2.25V to 3.63V with higher output drive, however, the data sheet parameters cannot be guaranteed. Please contact factory for
this option.
2. The output driver strenght can be programmed to drive up to 30pF load. Please contact factory for this option.
Page 2 of 7
SiT8002
DC Electrical Specifications
@VDD = 3.3V ±10%, -40 to 85°C
Parameter
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Operating Current
Standby Current
Power Up Time
Condition
IOH = -9 mA
IOL = 9 mA
Pin 1
Pin 1
Output frequency = 65 MHz, 15 pF load
Output is weakly pulled down, ST = GND
Time from minimum power supply voltage
Min.
90
-
70
-
-
-
-
Typ.
-
-
-
-
-
30
12
Max.
-
10
-
30
22
50
50
Unit
%Vdd
%Vdd
%Vdd
%Vdd
mA
uA
ms
@VDD = 2.5V ±10%, -40 to 85°C
Parameter
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Operating Current
Standby Current
Power Up Time
Condition
IOH = -7 mA
IOL = 7 mA
Pin 1
Pin 1
Output frequency = 65 MHz, 15 pF load
Output is weakly pulled down, ST = GND
Time from minimum power supply voltage
Min.
90
-
70
-
-
-
-
Typ.
-
-
-
-
-
30
12
Max.
-
10
-
30
22
50
50
Unit
%Vdd
%Vdd
%Vdd
%Vdd
mA
uA
ms
@VDD = 1.8V ±5%, -40 to 85°C
Parameter
Output Voltage High
Output Voltage Low
Input Voltage High
Input Voltage Low
Operating Current
Standby Current
Power Up Time
Condition
IOH = -5 mA
IOL = 5 mA
Pin 1
Pin 1
Output frequency = 65 MHz, 15 pF load
Output is weakly pulled down, ST = GND
Time from minimum power supply voltage
Min.
90
-
70
-
-
-
-
Typ.
-
-
-
-
-
30
12
Max.
-
10
-
30
19
50
50
Unit
%Vdd
%Vdd
%Vdd
%Vdd
mA
uA
ms
Page 3 of 7
SiT8002
AC Electrical Specifications
@VDD = 3.3V ±10%, -40 to 85°C
Parameter
Clock Output Frequency
Frequency
Tolerance
[3]
Inclusive of initial tolerance, operating temper-
ature, rated power supply voltage change, load
change,aging, shock and vibration
First year
Output frequency= 1 MHz to 125 MHz
15 pF Load, 20% to 80% VDD
15 pF Load, 80% to 20% VDD
Output frequency = 24 MHz
Output frequency = 100 MHz
Condition
Min.
1
-30
-50
-100
-
45
-
-
-
-
Typ.
-
-
-
-
-
-
1.0
1.0
-
-
Max.
125
+30
+50
+100
1
55
2.0
2.0
±98
±60
Unit
MHz
ppm
ppm
ppm
ppm
%
ns
ns
ps
ps
Aging
Clock Output Duty Cycle
Clock Output Rise Time
Clock Output Fall Time
Pk-pk Period Jitter
@VDD = 2.5V ±10%, -40 to 85°C
Parameter
Clock Output Frequency
Frequency Tolerance
[3]
Inclusive of initial tolerance, operating temper-
ature, rated power supply voltage change, load
change,aging, shock and vibration
First year
Output frequency= 1MHz to 125MHz
15 pF Load, 20% to 80% VDD
15 pF Load, 80% to 20% VDD
Output frequency = 24 MHz
Output frequency = 100 MHz
Condition
Min.
1
-30
-50
-100
-
45
-
-
-
-
Typ.
-
-
-
-
-
-
1.0
1.0
-
-
Max.
125
+30
+50
+100
1
55
2.0
2.0
±130
±60
Unit
MHz
ppm
ppm
ppm
ppm
%
ns
ns
ps
ps
Aging
Clock Output Duty Cycle
Clock Output Rise Time
Clock Output Fall Time
Pk-pk Period Jitter
@VDD = 1.8V ±5%, -40 to 85°C
Parameter
Clock Output Frequency
Frequency
Tolerance
[3]
Inclusive of initial tolerance, operating temper-
ature, rated power supply voltage change, load
change,aging, shock and vibration
First year
Output frequency= 1 MHz to 65MHz
Output frequency= 65 MHz to 125MHz
Clock Output Rise Time
Clock Output Fall Time
Pk-pk Period Jitter
15 pF Load, 20% to 80% VDD
15 pF Load, 80% to 20% VDD
Output frequency = 24 MHz
Output frequency = 100 MHz
Condition
Min.
1
-50
-100
-
45
40
-
-
-
-
Typ.
-
-
-
-
-
-
1.0
1.0
-
-
Max.
125
+50
+100
1
55
60
2.0
2.0
±185
±100
Unit
MHz
ppm
ppm
ppm
%
%
ns
ns
ps
ps
Aging
Clock Output Duty Cycle
Notes:
3. ±30 ppm is available only over extended commercial temperature range from-20 °C to +70 °C and VDD=2.5V or 3.3V.
[backcolor=royalblue][color=#ffffff]Note content preview: [/color][/backcolor][color=#ffffff] [/color] This application note describes the USB DFU protocol used in the STM32 microcontroller bootloader...
Some time ago, I used LM2776 to build a -5V circuit to power the op amp. After the board was completed, I found that the batch could not be powered, and the -5V was only about 0.6.
The circuit was als...
What is the use of this PowerOn? Can't calling Enable power the module? Do I need to call another function to do this? I don't quite understand the meaning of this function, please help me...
I'm a newbie. I'm just learning AVR microcontrollers. I need to implement the online update function of atmega128. But I'm not familiar with AVR. Can I call the library functions provided to write pro...
Dual-mode inverters can operate both in conjunction with the grid and independently. These inverters can inject excess energy from renewable energy and storage devices into the grid, and withdraw p...[Details]
The intelligent driving community has its own rhythm. Some are busy pushing new versions and focusing on R&D, others are busy with publicity and promotion, and still others are immersed in mass pro...[Details]
New energy vehicles are increasingly popular with consumers due to policies and energy conservation. Once you've purchased your vehicle, maintenance is essential. However, due to the different powe...[Details]
To understand why car engines need gearboxes, we must first understand the characteristics of different types of engines. An engine refers to a machine that can convert a form of energy into kineti...[Details]
Long ago, the lifespan of cars in my country was 15 years. Once a car reached 15 years old, it was forced to be scrapped. However, the policy was later changed. As long as the car does not exceed 6...[Details]
New energy pure electric vehicles generally accelerate faster than comparable fuel-powered vehicles, both from a standing start and while accelerating. Many believe this is simply due to the motor'...[Details]
summary
There are multiple approaches to making industrial systems more intelligent, including applying artificial intelligence (AI) technology at the edge and in the cloud to sensor...[Details]
The digital TV set-top box consists of a tuner, QAM demodulator, TS demultiplexer, MPEG-2 decoder, PAUNTSC video encoder, embedded CPU system and peripheral interfaces, CA module, and uplink data m...[Details]
Magna's integrated in-cabin perception system fuses vision and millimeter-wave radar data to detect the presence of passengers, identify stranded children, monitor driver fatigue and vital signs, a...[Details]
With the increasing popularity of automated equipment, linear modules, a common auxiliary device for automated equipment, have also seen a bright future. In particular, in recent years, many small ...[Details]
Nidec Precision Testing Technology Co., Ltd. will participate in "Testing Expo China—Automotive 2025" to be held at the Shanghai World Expo Exhibition and Convention Center from August 27 (Wednesda...[Details]
As the power density of modern electronic systems continues to increase, effective thermal management has become critical to ensuring system performance, reliability, and longevity—especially in hi...[Details]
When it comes to batteries, they're no strangers to car owners. But how should batteries be maintained? How often should they be replaced? What bad habits can affect their lifespan? And what's the ...[Details]
The drive shaft is a high-speed, low-support rotating body, so its dynamic balance is crucial. Generally, drive shafts undergo dynamic balancing tests and adjustments on a balancing machine before ...[Details]
This series of articles aims to help readers have a brief understanding of the Hongke KPA Automation system and to quickly get started with MoDK, including: an introduction to Hongke KPA Automation...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
