EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4Q001EG-1146CDI

Description
Programmable Oscillators PROGRAMMABLE 5X7 OSCILLATOR
CategoryPassive components   
File Size163KB,20 Pages
ManufacturerIDT (Integrated Device Technology)
Download Datasheet Parametric View All

8N4Q001EG-1146CDI Online Shopping

Suppliers Part Number Price MOQ In stock  
8N4Q001EG-1146CDI - - View Buy Now

8N4Q001EG-1146CDI Overview

Programmable Oscillators PROGRAMMABLE 5X7 OSCILLATOR

8N4Q001EG-1146CDI Parametric

Parameter NameAttribute value
Product AttributeAttribute Value
ManufacturerIDT (Integrated Device Technology)
Product CategoryProgrammable Oscillators
RoHSN
ProductXO
Package / Case7 mm x 5 mm
Length7 mm
Width5 mm
Height1.55 mm
PackagingTube
Factory Pack Quantity364
Unit Weight0.006562 oz
Quad-Frequency Programmable XO IDT8N4Q001 REV G
DATA SHEET
General Description
The IDT8N4Q001 is a Quad-Frequency Programmable Clock
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock® NG technology for
an optimum high clock frequency and low phase noise performance.
The device accepts 2.5V or 3.3V supply and is packaged in a small,
lead-free (RoHS 6) 10-lead ceramic 5mm x 7mm x 1.55mm package.
Besides the four default power-up frequencies set by the FSEL0 and
FSEL1 pins, the IDT8N4Q001 can be programmed via the I
2
C
interface to output clock frequencies between 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz to a very high degree of
precision with a frequency step size of 435.9Hz ÷
N
(N is the PLL
output divider). Since the FSEL0 and FSEL1 pins are mapped to four
independent PLL divider registers (P, MINT, MFRAC and N),
reprogramming those registers to other frequencies under control of
FSEL0 and FSEL1 is supported. The extended temperature range
supports wireless infrastructure, telecommunication and networking
end equipment requirements.
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Four power-up default frequencies (see part number order
codes), re-programmable by I
2
C
I
2
C programming interface for the output clock frequency and
internal PLL control registers
Frequency programming resolution is 435.9Hz ÷N
One 2.5V, 3.3V LVDS clock output
Two control inputs for the power-up default frequency
LVCMOS/LVTTL compatible control inputs
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.253ps
(typical), integer PLL feedback configuration
RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.263ps
(typical), integer PLL feedback configuration
Full 2.5V or 3.3V supply modes
-40°C to 85°C ambient operating temperature
Available in Lead-free (RoHS 6) package
Block Diagram
OSC
f
XTAL
÷MINT,
MFRAC
2
25
FSEL1
FSEL0
SCLK
SDATA
OE
Pulldown
Pulldown
Pullup
Pullup
Pullup
Pin Assignment
÷P
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
÷N
Q
nQ
DNU 1
OE 2
GND 3
FSEL0 4
FSEL1 5
10 SCLK
9 SDATA
8 V
DD
7 nQ
6 Q
7
Configuration Register (ROM)
(Frequency, APR, Polarity)
I
2
C Control
IDT8N4Q001
10-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4Q001GCD
REVISION A
MARCH 6, 2012
1
©2012 Integrated Device Technology, Inc.
Two new books that were not in use - [Engineer Training Notes/Magnetic Components/PSOC On-Chip Components]
[i=s] This post was last edited by yyl830113 on 2015-1-24 11:06 [/i] Two new books, for sale at a low price,30 yuan each, 50 yuan for two, not including postage, if interested, please contact QQ: [col...
yyl830113 Buy&Sell
How to get the signal strength of WLAN?
Could you please tell me how to get the signal strength of WLAN? I need to use this in my application. Thank you!...
nibian Embedded System
MMWCAS-DSP-EVM implements QSPI-4 boot
Setting S4[5:0] to 110111, 000111, or 100111 can all enable QSPI-4 booting, but the latter two configurations require that there is no SD card or USB....
alan000345 DSP and ARM Processors
About the startup problem of UC3842
The starting voltage of UC3842 is 16V. After starting, it is powered by the transformer. In order to ensure that the transformer is always powered after starting, does the output voltage of the transf...
雪人001 Analogue and Mixed Signal
[Ask TI] Is there any way to save the DSP after API error 24 occurs?
Please tell me what is happening with my dspAPI error 24, the program cannot be erased, and it cannot be burned.After the dsp is connected to the emulator, the data on the on-chip flash and the data i...
安_然 Microcontroller MCU
EEWORLD University ---- Near Field Communication (NFC) Training Series Part 3: NFC Applications
Near Field Communication (NFC) Training Series Part 3: NFC Applications : https://training.eeworld.com.cn/course/5008...
wanglan123 Talking

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1942  2409  2020  571  2450  40  49  41  12  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号