• See the Regulatory Information Appendix (RIA) in
the “RoHS compliance” section of
www.3M.com/Interconnects for compliance
information (RIA E1 & C1 apply)
Date Modified: February 2, 2010
TS-2305-E
Sheet 1 of 3
Physical
Insulation:
Material: Glass Filled Polyester (PBT)
Flammability: UL 94V-0
Color: Gray
Contact:
Material: Copper Alloy
Plating:
Underplating: 50 μ” Min.Nickel
Wiping Area: See Ordering Information
Termination: See Ordering Information
Electrical
Current Rating: 3.0A at 30°C T-rise above ambient
Contact Resistance: ≤20 mΩ
Insulation Resistance: ≥1,000 MΩ,100V
DC
Withstanding Voltage: 1,000 V
AC
for 1 minute
Environmental
Temperature Rating:
-55°C to 125°C
Process Temperature Rating:
Maximum Insulator Temperature 191°C (solder wave process only)
UL File No.: E68080
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M
™
DIN C Form Plug
Right Angle, Solder Tail Termination
Table 1
Contact
Quantity
16
32
48
32
16
32
64
96
64
32
DIN 41612 Series
Part Number
DIN-016CPA-XXX-XXXX
DIN-032CPB-XXX-XXXX
DIN-048CPC-XXX-XXXX
DIN-032CPD-XXX-XXXX
DIN-016CPE-XXX-XXXX
DIN-032CPA-XXX-XXXX
DIN-064CPB-XXX-XXXX
DIN-096CPC-XXX-XXXX
DIN-064CPD-XXX-XXXX
DIN-032CPE-XXX-XXXX
A
54.40 [2.142]
54.40 [2.142]
54.40 [2.142]
54.40 [2.142]
54.40 [2.142]
94.00 [3.701]
94.00 [3.701]
94.00 [3.701]
94.00 [3.701]
94.00 [3.701]
B
44.56 [1.754]
44.56 [1.754]
44.56 [1.754]
44.56 [1.754]
44.56 [1.754]
85.20 [3.354]
85.20 [3.354]
85.20 [3.354]
85.20 [3.354]
85.20 [3.354]
C
38.10 [1.500]
38.10 [1.500]
38.10 [1.500]
38.10 [1.500]
38.10 [1.500]
78.74 [3.100]
78.74 [3.100]
78.74 [3.100]
78.74 [3.100]
78.74 [3.100]
D
48.26 [1.900]
48.26 [1.900]
48.26 [1.900]
48.26 [1.900]
48.26 [1.900]
88.90 [3.500]
88.90 [3.500]
88.90 [3.500]
88.90 [3.500]
88.90 [3.500]
4.90 ± 0.10
[.193]
10.20
[.402]
11.10
[.437]
1
2- 2.6
[ .102]
5
10
15
20
30
32
2.54
[.100]
D
5.08
[.200]
2.54
[.100]
6.00
[.236]
2.75 ± 0.250
[.108]
A(Max.)
B
5.08
[.200]
1.00
[.039]
PIN C1
PIN A1
PIN B1
C
mm
[inch]
2.95
[.116]
3.80
(.150)
Tolerance Unless Noted
X.
mm
± 0.50
.X
± 0.25
.XX
± 0.15
[ ] Dimension for Reference Only
WITH “A” RETENTION CLIP
RR1
WITHOUT RETENTION CLIP
SR1
WITH “B” RETENTION CLIPS
for .062 PCB thickness
RR1L
for .062 and .093 PCB thickness
TS-2305-E
Sheet 2 of 3
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M
™
DIN C Form Plug
Right Angle, Solder Tail Termination
DIN 41612 Series
2.54
[.100]
2.54
[.100]
Ø0.94-1.09
[.037-.043]
PLATED THROUGH HOLE
2 1
2.54
[.100]
c
b
a
5.08
[.200]
5.30
[.209]
C
D
Ø2.8-2.9
[.110-.114]
RECOMMENDED PCB LAYOUT
Ordering Information
DIN - XXXCP X - XXX - XX
Contact Quantity
SEE TABLE
A = A Row only (see note)
B = Rows A & C Filled
C = Rows A, B & C Filled
D = Rows A & B Filled
E = B Row only (see note)
Plating Options:
SH = 1 - 3 μ” Gold on Contact
120 - 200 μ” Matte Tin on Terminal
FJ = 10 - 20 μ” Gold on Contact
120 - 200 μ” Matte Tin on Terminal
KR = 30 - 40 μ” Gold on Contact
120 - 200 μ” Matte Tin on Terminal
HM = 3 μ” Gold on Contact, 7 μ” Min. PdNi
120 - 200 μ” Matte Tin on Terminal
Termination Options:
Solder TailTermination
SR1 = 2.75 [.108]
RR1L = 2.75 [.108] with ‘B’ retention clips
RR1 = 2.75 (.108) with “A” retention clips
Note: A and E options are currently not covered in UL File No. E68080
• This diagram serves only for Part Number descriptive definitions.
PLEASE CONTACT YOUR LOCAL SALES REPRESENTATIVE FOR CUSTOMER SPECIFIC PRODUCT CONFIGURATIONS.
TS-2305-E
Sheet 3 of 3
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase.
3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.
Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
Before we officially start, let’s take a look at the daily work of an FPGA engineer:
Start designing the code.Start writing the first always code.Found that a signal needs to be added, so write the se...
[align=left] The USB protocol is a relatively complex protocol, and beginners will definitely encounter many problems. Since I took many detours in the learning process, I wrote this article, hoping t...
I don't know the difference between the following two methods of programming directly using registers. Please advise.
The first one:
#include "hw_types.h"
#define SYSCTL_BASE 0x400FE000 /* Define the ...
In the process of learning single-chip microcomputers or electronic design, you will generally encounter some integrated devices, such as AT24C02, DS1302, DS18B20, including LCD modules 1602, 12864, e...
[font=微软雅黑][size=3]From daily life to Industry 4.0, we respond to a variety of motor needs. Electricity used by motors accounts for 40-50% of total electricity consumption worldwide, so motor drives n...
With the booming electronics industry, vision systems have become a leader in the electronics automation sector. However, the delicate nature of electronic products often affects product yields due...[Details]
On August 24th, media outlets reported, citing sources, that NavInfo, a listed company on the A-share market, is nearing completion in its acquisition of the intelligent driving c...[Details]
To understand why car engines need gearboxes, we must first understand the characteristics of different types of engines. An engine refers to a machine that can convert a form of energy into kineti...[Details]
Zos Automotive Research Institute released the "2025
Smart Cockpit
Tier 1 Research Report (Domestic Edition)."
This report analyzes the operating conditions of more than a dozen ...[Details]
introduction
The concept of the smart home is gradually developing and gaining market acceptance. We believe its ultimate form lies in the interconnection of all home appliances through open i...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
Keysight Technologies is combining its electromagnetic simulator with Synopsys' AI-driven RF design migration flow to create an integrated design flow for migrating from TSMC's N6RF+ process techno...[Details]
Plessey Semiconductors has been acquired by Haylo Labs, which was established in March last year with a $100 million, five-year loan from Chinese technology company Goertek.
Haylo Labs w...[Details]
Methods of DC motor speed regulation:
1. The voltage regulator can be used to change the input voltage and speed directly, which is often used for large kilowatt-level motors.
2. Thyristo...[Details]
Lightweighting of automobiles is still a relatively unfamiliar term for automobiles. With the continuous improvement of environmental protection requirements, relevant regulations have also put for...[Details]
Introduction: In digital circuit calculations, there is no concept of decimal points. You know where the decimal is, but the circuit does not know where the decimal point is. Therefore, you need to...[Details]
Hair dryer structure and working principle: It is mainly used for drying and shaping hair, but it can also be used for local drying, heating and treatment in laboratories, physiotherapy rooms, ind...[Details]
Traditionally, electrical energy is transmitted primarily through wires, requiring direct physical contact between the power source and the load. With the increasing number of electrical devices in...[Details]
This series of articles aims to help readers have a brief understanding of the Hongke KPA Automation system and to quickly get started with MoDK, including: an introduction to Hongke KPA Automation...[Details]
Since entering the electronic components industry, I've learned that electronic components come in different packaging types. Some people have argued that different types of components may look the...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
