EEWORLDEEWORLDEEWORLD

Part Number

Search

142-0307-401

Description
RF Connectors / Coaxial Connectors SMA BULKHEAD JACK RG58/U 141 303 GOLD
CategoryThe connector    The connector   
File Size1022KB,3 Pages
ManufacturerCinch Connectivity Solutions
Download Datasheet Parametric View All

142-0307-401 Online Shopping

Suppliers Part Number Price MOQ In stock  
142-0307-401 - - View Buy Now

142-0307-401 Overview

RF Connectors / Coaxial Connectors SMA BULKHEAD JACK RG58/U 141 303 GOLD

142-0307-401 Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresAPPLICABLE CABLES: RG 58/U; RG 141; RG 303, INSERTION LOSS MAX AT 6GHZ, CAPTIVE CONTACT
Body/casing typeJACK
Characteristic impedance50 Ω
Connector typeRF SMA CONNECTOR
Contact to complete cooperationGOLD (30)
Contact completed and terminatedGOLD (30)
Contact point genderFEMALE
Coupling typeTHREADED
DIN complianceNO
Filter functionNO
IEC complianceNO
Insertion loss0.15 dB
insulator materialPTFE FLUOROCARBON/PFA
JESD-609 codee4
MIL complianceNO
Manufacturer's serial numberSMA
Installation methodSTRAIGHT
Installation typeCABLE
Maximum operating frequency12.4 GHz
OptionsGENERAL PURPOSE
Panel mountingYES
Termination typeCRIMP
voltage standing wave ratio1.27
Base Number Matches1
SMA 50 Ohm
Straight Crimp Type Bulkhead Jack -
Captivated Contact
INCHES (MILLIMETERS)
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST
CABLE
TYPE
RG-58/U, 141, 303
VSWR &
FREQ. RANGE
1.15 + .01 f (GHz) 0-12.4 GHz
GOLD
PLATED
142-0307-401
NICKEL
PLATED
142-0307-406
Mounting hole layout
CABLE GROUP
RG-58/u,
141, 303
PART NUMBER CRIMP HEX
142-0307-401 .213 (5.41)
142-0307-406 .213 (5.41)
1. Identify connector parts. (6 piece parts - except bulkhead)
2. Strip cable to dimensions shown. Do not nick braid or cen-
ter conductor. A wire stripper of correct size is recommended
for this step. Twist stranded center conductor into tight
bundle and tin (optional). Slide crimp sleeve, nut and heat
shrink tubing (as applicable) onto cable as shown.
3. Flare braid and slide cable into crimp stem. Place rear insu-
lator and center contact over center conductor and position
as shown for different cable sizes. Solder center conductor
to contact through the solder hole. Solder
must not
be al-
lowed to gather and run on outside of contact. Use a mini-
mum amount of solder for a good joint.
.020 (0.51) diam-
eter solder is recommended.
4. Arrange braid uniformly around crimp stem. Slide crimp
sleeve over braid and crimp securely using recommended
crimp tool. Slide center contact assembly into connector
body. Thread coupling nut onto body and tighten to 10 in.-
lb. torque. Slide heat shrink forward and shrink (as appli-
cable).
Cinch Connectivity Solutions
299 Johnson Avenue SW, Waseca, MN 56093 USA • 800.247.8256 • +1 507 833 8822 • cinchconnectivity.com
【Nucleo In-depth Review】Nucleo-L053 joins CoOS...
Nucleo-L053 adds CoOS operating system. For details about CoOS, please visit [url]http://www.coocox.org[/url]. CooCox CoOS CooCox CoOS is a real-time system kernel designed for ARM Cortex-M series chi...
水清波 MCU
Question: How to connect a 1UF/400V capacitor in a 220V AC circuit?
I would like to ask: If a 1UF/400V capacitor is connected in parallel to a 220V AC circuit and a 3.6K/15W resistor is connected in parallel to a 220V AC circuit, are their power consumption (watt-hour...
book1 Test/Measurement
DSP Learning (2) Overview of TMS320VC5402
Chapter 2 Overview of TMS320VC5402The most widely used DSPs in the industry are TI's TMS320 series DSPs. TMS320C5402 is a highly cost-effective fixed-point digital signal processor DSPs launched by TI...
Aguilera DSP and ARM Processors
Hardware Engineer Basic Knowledge Outline
Purpose: Based on practical experience and actual projects, you will understand and master the most basic knowledge to become a qualified hardware engineer. 1) Basic design specifications 2) Basic kno...
kandy2059 Automotive Electronics
How to isolate interference in the line
If the microcontroller serial port and the driver module are placed on the same wire and the load is working, it will burn the microcontroller. What is the best communication method for this serial po...
tangwei8802429 Analog electronics
Communication between ABB PLC and Honeywell EB I
Combining the typical project of communication between Honeywell's building monitoring software platform EBI and ABB's Modbus protocol PLC, this paper points out the Modbus protocol content that shoul...
frozenviolet Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1036  1911  947  599  904  21  39  20  13  19 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号