Large Diameter (56 mm),
Housed Two and Three
Channel Optical Encoders
Technical Data
HEDL-65xx
HEDM-65xx
HEDS-65xx Series
Features:
• Two Channel Quadrature
Output with Optional
Index Pulse
• TTL Compatible Single Ended
Outputs on HEDS Series
• 100
°
C Operating Temperature
• Industry Standard 26C31
CMOS Line Driver IC on
HEDL Series
• Easy Assembly, No Signal
Adjustment Necessary
• Resolutions up to 2048 Counts
Per Revolution
• Maximum Shaft Diameter
of 5/8 Inches
• Single +5 V Supply
outputs. This index is an active
high pulse that occurs once every
full rotation of the codewheel.
Resolutions up to 1024 Counts Per
Revolution are available in the two
and three channel versions.
The line driver option offers
enhanced performance when the
encoder is used in noisy environ-
ments, or when it is required to
drive long distances.
The line driver option utilizes an
industry standard line driver IC
(26C31) which provides comple-
mentary outputs for each encoder
channel. Thus the outputs of the
–
line driver encoder are A and A, B
–
–
and B, and I and I for three
channel versions. Suggested line
receivers are 26C32 and 26C33.
The quadrature signals are ac-
cessed through a cable and 10-pin
female connector. Please refer to
the ordering information at the end
of this data sheet for a selection
matrix.
Applications
The HEDS-65xx / HEDL-65xx
provide motion detection to a
very high resolution and accept a
variety of shaft sizes up to a
maximum of 5/8 inches.
Description
The HEDS-65xx/HEDL-65xx
are high performance two and three
channel optical incremental
encoders. These encoders empha-
size high reliability, high resolution,
and easy assembly. Each encoder
contains a lensed LED source
(emitter), an integrated circuit with
detectors and output circuitry, and a
codewheel which rotates between
the emitter and detector integrated
circuit. The outputs of the HEDS-
6500 are two single ended square
waves in quadrature. The HEDL-
65xx outputs are differential.
The HEDS-6540 / HEDL-6540 also
have a third channel index output in
addition to the two quadrature
4
Theory of Operation
The HEDS-65xx / HEDL-65xx
translate the rotary motion of a
shaft into either a two or three
channel digital output.
The HEDS-65xx uses one of
the standard HEDS-9000 or
HEDS-9040 modules for
encoding purposes. The
HEDL-654x uses the standard
HEDL-9040 for encoding
purposes.
As seen in the block diagram,
these modules contain a single
Light Emitting Diode (LED) as
their light source (emitter). The
light is collimated into a single
parallel beam by means of a
plastic lens located directly over
the LED. Opposite the emitter is
the integrated detector circuit
(detector). This circuit consists
of multiple sets of photodetectors
and the signal processing circuitry
necessary to produce the digital
waveforms.
The codewheel rotates between
the emitter and detector, causing
the light beam to be interrupted
by a pattern of spaces and bars
on the codewheel. The photodiodes
which detect these interruptions
are arranged in a pattern that
corresponds to the radius and
design of the codewheel. These
detectors are also spaced such
that a light period on one pair of
detectors corresponds to a dark
period on the adjacent pair of
detectors. The photodiode outputs
are then fed into the signal
processing circuitry resulting
–
–
–
in A, A, B, and B (I and I also in
the three channel encoders).
Comparators receive these
signals and produce the final
outputs for channels A and B.
Due to this integrated phasing
technique, the digital output of
channel A is in quadrature with
that of channel B (90 degrees out
of phase).
In the HEDS-6540 / HEDL-6540
the output of the comparator for
the index pulse is combined with
that of the outputs of channel A
and channel B to produce the final
index pulse. The index pulse is
generated once every rotation of
the codewheel and is a one state
width (nominally 90 electrical
degrees), true high index pulse.
It is coincident with the low states
on channels A and B.
Pulse Width (P): The number of
electrical degrees that an output
is high during one cycle. This
value is nominally 180 e or 1/2
cycle.
Pulse Width Error (∆P): The
deviation, in electrical degrees,
of the pulse width from its ideal
value of 180 e.
State Width (S): The number
of electrical degrees between a
transition in the output of
channel A and the neighboring
transition in the output of
channel B. There are 4 states
per cycle, each nominally 90 e.
State Width Error (∆S): the
deviation, in electrical degrees,
of each state width from its ideal
value of 90 e.
Phase (Φ): the number of electrical
degrees between the center of
high state on channel A and
the center of the high state on
channel B. This value is nominally
90 e for quadrature output.
Phase Error (∆Φ): The deviation
of the phase from its ideal value
of 90 e.
Direction of Rotation: When the
codewheel rotates in a counter-
clockwise direction (when viewed
from the encoder end of the motor)
channel A will lead channel B.
If the codewheel rotates in the
clockwise direction channel B
will lead channel A.
Index Pulse Width (P0): The
number of electrical degrees that
an index output is high during
one full shaft rotation. This value
is nominally 90 e or 1/4 cycle.
Definitions
Count (N): The number of bar
and window pairs or counts per
revolution (CPR) of the codewheel.
One Cycle (C): 360 electrical
degrees (e), 1 bar and window
pair.
One Shaft Rotation: 360
mechanical degrees, N cycles.
Position Error (∆Θ): The normal-
ized angular difference between
the actual shaft position and the
position indicated by the encoder
cycle count.
Cycle Error (∆C): An indication
of cycle uniformity. The difference
between an observed shaft angle
which gives rise to one electrical
cycle, and the nominal angular
increment of 1/N of a revolution.
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
