Notes: (Ref) – Dimensions provided for reference only. For low profile cases, no dimensions are provided for B, P or R because these cases do not have a
(1) To complete KEMET part number, insert M for ±20% or K for ±10%. Designates capacitance tolerance.
(2) To complete KEMET part number, insert T = 100% Matte Tin (Sn) Plated, G = Gold Plated, H = Standard Solder coated (SnPb 5% Pb minimum).
Designates termination finish.
Refer to Ordering Information for additional detail.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitution will
be marked with the higher voltage rating. Substitutions can include better than series.
I use T0 to receive pulses, T1 to time 50ms (the natural frequency of the crystal oscillator is 11.0592MHZ), and finally I give the high eight bits and low eight bits of T0 to A and B respectively. So...
Introduction to msp430f149 microcontroller: MSP430 series microcontroller is a 16-bit ultra-low power mixed signal processor (Mixed Signal Processor) with a reduced instruction set (RISC) that was lau...
Regarding the problem of LPM_ROM in Modelsim simulation of Altera, when doing functional simulation, the following error is always prompted: # ** Error: (vsim-7) Failed to open VHDL file "my_rom.hex" ...
When I use the development board to connect to the instrument via the serial port, I can continuously receive data, but the later data cannot overwrite the previous data. How can I make the later data...
Dear bosses: After entering the CE system, right-click on the desktop (or long press on the touch screen), the display properties will appear. The second item of the display properties is "Backlight"....
[i=s]This post was last edited by lb8820265 on 2015-10-4 20:17[/i] [align=left][font=宋体] [size=3]This post is for the DIY[font=宋体] sharing event on September 10. It just so happens that a part of the ...
In 2017,
Sanan Optoelectronics
achieved sales revenue of 8.394 billion yuan, operating profit of 3.856 billion yuan, and net profit attributable to shareholders of the parent company of 3.1...[Details]
1. Test conditions Hardware: STM32L432KC Main frequency: 80MHz Compiler: IAR 8.20.1 Compiler options: High Speed no size constraints CRC generator polynomial: 0x782f 2. Test Method The softwar...[Details]
Although it is early summer, the Chinese smartphone market is still in the cold winter, just like Beijing in April with snow. For mobile phone brands caught in the middle, the cold is even more bit...[Details]
The application of millimeter wave technology in mobile communications also involves a series of technical problems, including the large propagation loss of millimeter waves and the susceptibility ...[Details]
This example is mainly to familiarize yourself with the register configuration of Timer A and the configuration method of IAR. /*********************************************** Program function: re...[Details]
On May 16, in response to
the public opinion storm caused by
Lenovo's
"
5G
voting" incident,
Lenovo
Holdings Chairman and
Lenovo
Group Founder Liu Chuanzhi, Lenovo Gr...[Details]
I have been working on a stm32 project recently and have been struggling with its startup method. I saw a good article and reposted it. The format of the original article is not very good, and there...[Details]
As shown in the figure, the author soldered a STM32F207VET6 board using a TQFP (32-100PIN) 0.55MM to direct plug adapter board. The board leads out the SWD debug interface (only PA13 and PA14 are occ...[Details]
The storage media corresponding to the three boot modes of STM32 are built-in to the chip, they are: 1. User Flash = Flash built into the chip 2.SRAM = RAM area built into the chip, which is the m...[Details]
STM32 has three startup modes. In RM0008 downloaded from the ST official website, you can find the startup-related configuration instructions: Translated into Chinese: The storage media corresp...[Details]
When the program starts running, light A turns on for 5 seconds, then turns off, light B turns on for 5 seconds, light B turns off, light C turns on for 5 seconds, light C turns off, the program ends...[Details]
Use common anode digital tube and independent keyboard to connect P1 and P2 ports of single chip to realize answering machine The procedure is as follows: #include reg52.h void delay(unsigned char n)...[Details]
Single-chip microcomputer experiment design: It is required to use 8951 series single-chip microcomputer, design a pulse generator with a pulse width duty cycle of 50%, 25% adjustable, and a period o...[Details]
Assume that both the augend NA and the addend NB are three-byte compressed BCD codes, which are stored in the internal RAM units 20H~22H and 30H~32H, respectively, with the low digit first and the hi...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
