DATASHEET
ISL32600E, ISL32601E, ISL32602E, ISL32603E
1.8V to 3.3V, Micro-Power, ±15kV ESD, +125 °C, Slew Rate Limited
RS-485/RS-422 Transceivers
The Intersil
ISL32600E, ISL32601E, ISL32602E,
and
ISL32603E
are ±15kV IEC61000 ESD protected, micro-power,
wide supply range transceivers for differential communication.
The ISL32600E and ISL32601E operate with V
CC
≥
2.7V and
have maximum supply currents as low as 100µA with both the
transmitter (Tx) and receiver (Rx) enabled. The ISL32602E and
ISL32603E operate with supply voltages as low as 1.8V. These
transceivers have very low bus currents, so they present less
than a “1/8 unit load” to the bus. This allows more than 256
transmitters on the network without violating the RS-485
specification’s 32 unit load maximum.
Rx inputs feature symmetrical switching thresholds and up to
65mV of hysteresis to improve noise immunity and to reduce
duty cycle distortion in the presence of slow moving input
signals (see
Figure 9 on page 12).
The Rx input common mode
range is the full -7V to +12V RS-485 range for supply
voltages
≥
3V.
Hot plug circuitry ensures that the Tx and Rx outputs remain in
a high impedance state while the power supply stabilizes.
This transceiver family uses slew rate limited drivers, which
reduce EMI, and minimize reflections from improperly terminated
transmission lines or from unterminated stubs in multidrop and
multipoint applications.
The ISL32600E and ISL32602E are configured for full duplex
(separate Rx input and Tx output pins) applications. The
ISL32601E and ISL32603E are half duplex versions that
multiplex the Rx inputs and Tx outputs to allow transceivers
with output disable functions in 8 Ld packages.
Table 1 on
page 2
provides a summary of each device’s features.
FN7967
Rev.1.00
Oct 20, 2017
Features
• Single 1.8V, 3V, or 3.3V supply
• Low supply currents
- ISL32601E . . . . . . . . . . . . . . . . . . . . . . . 100µA (Max) at 3V
- ISL32603E . . . . . . . . . . . . . . . . . . . . . .150µA (Max) at 1.8V
• Ultra low shutdown supply current. . . . . . . . . . . . . . . . . . 10nA
• IEC61000 ESD protection on RS-485 I/O pins. . . . . . . ±15kV
- Class 3 ESD levels on all other pins. . . . . . . . . . >8kV HBM
• Symmetrical switching thresholds for less duty cycle
distortion (see
Figure 9 on page 12)
• Up to 65mV hysteresis for improved noise immunity
• Data rates from 128kbps to 460kbps
• Specified for +125°C operation
• 1/8 unit load allows up to 256 devices on the bus
• -7V to +12V Common Mode input/output voltage range
(V
CC
≥
3V)
• Half and full duplex pinouts; three state Rx and Tx outputs
• 5V tolerant logic inputs
• Tiny MSOP packages consume 50% less board space
Applications
• Differential sensor interfaces
• Process control networks
• Security camera networks
• Building environmental control/lighting systems
Related Literature
• For a full list of related documents, visit our website
-
ISL32600E, ISL32601E, ISL32602E,
and
ISL32603E
product pages
10m
ISL3172E DYNAMIC (9.6kbps)
1m
ISL3172E STATIC
DE = V
CC
, RE = GND
25°C, R
D
= ∞, C
D
= 50pF
DYNAMIC (256kbps)
I
CC
(A)
I
CC
(A)
ISL3260XE DYNAMIC (9.6kbps)
100µ
ISL3260XE STATIC
DYNAMIC (128kbps)
1m
STATIC
DE = V
CC
, RE = GND
10µ
2.7
2.8
2.9
3
25°C, R
D
= ∞, C
D
= 50pF
3.1
3.2
3.3
3.4
3.5
3.6
100µ
1.8
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
FIGURE 1. THE ISL32600E AND ISL32601E HAVE A 9.6kbps
OPERATING I
CC
LOWER THAN THE STATIC I
CC
OF
MANY EXISTING 3V TRANSCEIVERS
FIGURE 2. THE ISL32602E AND ISL32603E WITH V
CC
= 1.8V
REDUCE OPERATING I
CC
BY A FACTOR OF 25 TO 40,
COMPARED WITH I
CC
AT V
CC
= 3.3V
FN7967 Rev.1.00
Oct 20, 2017
Page 1 of 23
ISL32600E, ISL32601E, ISL32602E, ISL32603E
TABLE 1. SUMMARY OF FEATURES
PART
NUMBER
ISL32600E
ISL32601E
ISL32602E
ISL32603E
SUPPLY
RANGE (V)
2.7 to 3.6
2.7 to 3.6
1.8 to 3.6
1.8 to 3.6
HALF/FULL
DUPLEX
FULL
HALF
FULL
HALF
DATA RATE
(kbps)
128 - 256
128 - 256
256 - 460
256 - 460
SLEW-RATE
LIMITED?
YES
YES
YES
YES
HOT
PLUG?
YES
YES
YES
YES
# DEVICES
ON BUS
256
256
256
256
RX/TX
ENABLE?
YES
YES
YES
YES
QUIESCENT
I
CC
(µA)
60 @ 3V
60 @ 3V
105 @ 1.8V
105 @ 1.8V
LOW POWER
SHUTDOWN?
YES
YES
YES
YES
PIN
COUNT
10, 14
8
10, 14
8
Pin Configurations
ISL32601E, ISL32603E
(8 LD MSOP, SOIC)
TOP VIEW
RO 1
RE 2
DE 3
DI 4
D
R
8
7
6
5
V
CC
B/Z
A/Y
GND
ISL32600E, ISL32602E
(10 LD MSOP)
TOP VIEW
RO 1
RE 2
DE 3
DI 4
GND 5
D
R
10 V
CC
9 A
8 B
7 Z
6 Y
ISL32600E, ISL32602E
(14 LD SOIC)
TOP VIEW
NC 1
RO 2
RE 3
DE 4
DI 5
GND 6
GND 7
D
R
14 V
CC
13 NC
12 A
11 B
10 Z
9 Y
8 NC
Ordering Information
PART NUMBER (Notes
1, 2, 3)
ISL32600EFBZ
ISL32600EFUZ
ISL32601EFBZ
ISL32601EFUZ
ISL32602EFBZ
ISL32602EFUZ
ISL32603EFBZ
ISL32603EFUZ
NOTES:
1. Add “-T” suffix for 2.5k unit or “-T7A” suffix for 250 unit tape and reel options. Refer to
TB347
for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), refer to the device information pages for the
ISL32600E, ISL32601E, ISL32602E,
and
ISL32603E.
For more
information on MSL, refer to
TB363.
PART MARKING
32600EFBZ
32600
32601 EFBZ
32601
32602EFBZ
32602
32603 EFBZ
32603
TEMP. RANGE (°C)
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
-40 to +125
PACKAGE (Pb-Free)
14 Ld SOIC
10 Ld MSOP
8 Ld SOIC
8 Ld MSOP
14 Ld SOIC
10 Ld MSOP
8 Ld SOIC
8 Ld MSOP
PKG. DWG. #
M14.15
M10.118
M8.15
M8.118
M14.15
M10.118
M8.15
M8.118
FN7967 Rev.1.00
Oct 20, 2017
Page 2 of 23
ISL32600E, ISL32601E, ISL32602E, ISL32603E
Truth Tables
TRANSMITTING
INPUTS
RE
X
X
0
1
DE
1
1
0
0
DI
1
0
X
X
Z
0
1
High-Z
High-Z *
OUTPUTS
Y
1
0
High-Z
High-Z *
Truth Tables
(continued)
RECEIVING
INPUTS
RE
0
0
0
0
1
1
DE
DE
Half Duplex Full Duplex
0
0
0
0
0
1
X
X
X
X
0
1
A-B
V
AB
≥
0.2V
OUTPUT
RO
1
0.2V > V
AB
> -0.2V Undetermined
V
AB
≤
-0.2V
Inputs Open
X
X
0
1
High-Z *
High-Z
NOTE: *Shutdown Mode (See
Note 11).
NOTE: *Shutdown Mode (See
Note 11).
Pin Descriptions
PIN
RO
RE
DE
DI
GND
A/Y
B/Z
A
B
Y
Z
V
CC
NC
8 LD
10 LD
14 LD
PACKAGE PACKAGE PACKAGE
1
2
3
4
5
6
7
-
-
-
-
8
-
1
2
3
4
5
-
-
9
8
6
7
10
-
2
3
4
5
6, 7
-
-
12
11
9
10
14
1, 8, 13
FUNCTION
Receiver output: If A-B
≥
200mV, RO is high; if A-B
≤
-200mV, RO is low; if A and B are unconnected (floating),
RO = high.
Receiver output enable. RO is enabled when RE is low; RO is high impedance when RE is high. If the Rx enable
function is not required, connect RE directly to GND.
Driver output enable. The driver outputs, Y and Z, are enabled by bringing DE high, and are high impedance
when DE is low. If the Tx enable function is not required, connect DE to V
CC
.
Driver input. A low on DI forces output Y low and output Z high. Similarly, a high on DI forces output Y high
and output Z low.
Ground connection.
±15kV IEC61000 ESD protected RS-485/422 level, noninverting receiver input and noninverting driver
output. Pin is an input if DE = 0; pin is an output if DE = 1.
±15kV IEC61000 ESD protected RS-485/422 level, Inverting receiver input and inverting driver output. Pin is
an input if DE = 0; pin is an output if DE = 1.
±15kV IEC61000 ESD protected RS-485/422 level, noninverting receiver input.
±15kV IEC61000 ESD protected RS-485/422 level, inverting receiver input.
±15kV IEC61000 ESD protected RS-485/422 level, noninverting driver output.
±15kV IEC61000 ESD protected RS-485/422 level, inverting driver output.
System power supply input (2.7V to 3.6V for the ISL32600E and ISL32601E; 1.8V to 3.6V for the ISL32602E
and ISL32603E).
No internal connection.
FN7967 Rev.1.00
Oct 20, 2017
Page 3 of 23
ISL32600E, ISL32601E, ISL32602E, ISL32603E
Typical Operating Circuits
HALF DUPLEX NETWORK USING ISL32603E
+1.8V
+
8
V
CC
1 RO
2 RE
3 DE
4 DI
D
GND
5
GND
5
R
B/Z
A/Y
7
6
7
6
B/Z
A/Y
R
0.1µF
0.1µF
+
8
V
CC
D
DI 4
DE 3
RE 2
RO 1
+1.8V
}
Note 14
FULL DUPLEX NETWORK USING ISL32600E
+3.3V
+
14
V
CC
2 RO
3 RE
4 DE
5 DI
Z 10
D
GND
6, 7
Y 9
R
T
11 B
12 A
GND
6, 7
R
R
A 12
B 11
0.1µF
R
T
(PIN NUMBERS FOR SOIC)
0.1µF
+
14
9 Y
10 Z
V
CC
D
DI 5
DE 4
RE 3
RO 2
+3.3V
}
Note 14
FN7967 Rev.1.00
Oct 20, 2017
Page 4 of 23
ISL32600E, ISL32601E, ISL32602E, ISL32603E
Absolute Maximum Ratings
V
CC
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
Input Voltages
DI, DE, RE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7V
Input/Output Voltages
A, B, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -8V to +13V
A/Y, B/Z, Y, Z (V
CC
= 0V or
≥
3V) . . . . . . . . . . . . . . . . . . . . . . . -8V to +13V
A/Y, B/Z, Y, Z (1.8V
≤
V
CC
< 3V) . . . . . . . . . . . . . . . . . . . . . . . -8V to +11V
RO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to (V
CC
+0.3V)
Short Circuit Duration
Y, Z. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indeterminate
ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Specification Table
Latch-up (per JESD78, Level 2, Class A) . . . . . . . . . . . . . . . . . . . . . . +125°C
Thermal Information
Thermal Resistance (Typical, Notes 4, 5)
JA
(°C/W)
JC
(°C/W)
8 Ld SOIC Package . . . . . . . . . . . . . . . . . . . .
105
47
8 Ld MSOP Package . . . . . . . . . . . . . . . . . . .
140
40
10 Ld MSOP Package . . . . . . . . . . . . . . . . . .
160
59
14 Ld SOIC Package . . . . . . . . . . . . . . . . . . .
128
39
Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see
TB493
Recommended Operating Conditions
Supply Voltage Range
ISL32600E, ISL32601E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3V to 3.3V
ISL32602E, ISL32603E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8V to 3.3V
Differential Load Resistance
ISL32600E, ISL32601E . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Ω or 120Ω
ISL32602E, ISL32603E . . . . . . . . . . . . . .
≥10kΩ
at 1.8V; 120Ω at 3.3V
Recommended Operating Conditions
(continued)
Common Mode Range
ISL32600E, ISL32601E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7V to +12V
ISL32602E, ISL32603E
V
CC
= 1.8V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2V to +2V
V
CC
= 3.3V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7V to +12V
Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +125°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4.
JA
is measured with the component mounted on a high-effective thermal conductivity test board in free air. Refer to
TB379
for details.
5. For
JC
, the “case temp” location is taken at the package top center.
ISL32600E, ISL32601E Electrical Specifications
PARAMETER
SYMBOL
Test Conditions: V
CC
= 2.7V to 3.6V; typical values are at V
CC
= 3V,
T
A
= +25°C; unless otherwise specified. Boldface limits apply over the operating temperature range. (Note
6)
TEST CONDITIONS
TEMP
(°C)
MIN
(Note
15)
TYP
MAX
(Note
15)
UNITS
DC CHARACTERISTICS
Driver Differential V
OUT
V
OD
R
L
= 100Ω (RS-422) (Figure
3A,
V
CC
≥
3.15V)
R
L
= 54Ω (RS-485)
(Figure 3A)
No Load
R
L
= 60Ω, -7V
≤
V
CM
≤
12V (Figure
3B,
V
CC
≥
3V)
Change in Magnitude of Driver
Differential V
OUT
for
Complementary Output States
Driver Common-Mode V
OUT
Change in Magnitude of Driver
Common-Mode V
OUT
for
Complementary Output States
Output Leakage Current (Y, Z) (Full
Duplex Versions Only)
V
OD
R
L
= 54Ω or 100Ω (Figure
3A)
V
CC
= 2.7V
V
CC
≥
3V
Full
Full
Full
Full
Full
Full
1.95
1.2
1.4
-
1.3
-
2.1
1.5
1.7
-
-
0.01
-
V
CC
V
CC
V
CC
-
0.2
V
V
V
V
V
V
V
OC
V
OC
R
L
= 54Ω or 100Ω (Figure
3A)
R
L
= 54Ω or 100Ω (Figure
3A)
Full
Full
-
-
-
0.01
3
0.2
V
V
I
OZD
DE = 0V, V
CC
= 0V
(-7V
≤
V
IN
≤
12V) or
2.7V
≤
V
CC
≤
3.6V
V
IN
= 12V (V
CC
≥
3V)
V
IN
= 10V (V
CC
= 2.7V)
V
IN
= -7V
Full
Full
Full
Full
Full
Full
Full
-
-
-30
-
2
-
-1
3
3
-10
-
-
-
-
60
60
-
±250
-
0.7
1
µA
µA
µA
mA
V
V
µA
Driver Short-Circuit Current,
V
O
= High or Low
Logic Input High Voltage
Logic Input Low Voltage
Logic Input Current
I
OSD
V
IH
V
IL
I
IN1
DE = V
CC
, -7V
≤
V
Y
or V
Z
≤
12V (Note
8)
DI, DE, RE
DI, DE, RE
DI = DE = RE = 0V or V
CC
(Note
14)
FN7967 Rev.1.00
Oct 20, 2017
Page 5 of 23
京公网安备 11010802033920号
EEWORLD
