FUJITSU SEMICONDUCTOR
DATA SHEET
DS07-13750-4E
16-bit Microcontroller
CMOS
F
2
MC-16LX MB90920 Series
MB90F922NC/F922NCS/922NCS/F923NC/F923NCS/
MB90F924NC/F924NCS/V920-101/V920-102
■
DESCRIPTION
The MB90920 series is a family of general-purpose FUJITSU SEMICONDUCTOR 16-bit microcontrollers de-
signed for applications such as vehicle instrument panel control.
The instruction set retains the AT architecture from the F
2
MC-8L and F
2
MC-16LX families, with further refinements
including high-level language instructions, extended addressing modes, improved multiplication and division
operations (signed), and bit processing. In addition, long word processing is made possible by the inclusion of a
built-in 32-bit accumulator.
Note : F
2
MC is the abbreviation of FUJITSU Flexible Microcontroller.
■
FEATURES
• Clock
Built-in PLL clock frequency multiplication circuit.
Selection of machine clocks (PLL clocks) is allowed among frequency division by two on oscillation clock, and
multiplication of 1 to 8 times of oscillation clock (for 4 MHz oscillation clock, 4 MHz to 32 MHz).
Operation by sub clock (up to 50 kHz : 100 kHz oscillation clock divided by two) is allowed.
• 16-bit input capture (8 channels)
Detects rising, falling, or both edges.
16-bit capture register
×
8
The value of a 16-bit free-run timer counter is latched upon detection of an edge input to pin and an interrupt
request is generated.
(Continued)
For the information for microcontroller supports, see the following web site.
This web site includes the
"Customer Design Review Supplement"
which provides the latest cautions on
system development and the minimal requirements to be checked to prevent problems before the system
development.
http://edevice.fujitsu.com/micom/en-support/
Copyright©2007-2010 FUJITSU SEMICONDUCTOR LIMITED All rights reserved
2010.9
MB90920 Series
(Continued)
• 16-bit reload timer (4 channels)
16-bit reload timer operation (select toggle output or one-shot output)
Selectable event count function
• Real time watch timer (main clock)
Operates directly from oscillator clock.
Interrupt can be generated by second/minute/hour/date counter overflow.
• PPG timer (6 channels)
Output pins (3 channels), external trigger input pin (1 channel)
Operation clock frequencies : f
CP
, f
CP
/2
2
, f
CP
/2
4
, f
CP
/2
6
• Delay interrupt
Generates interrupt for task switching.
Interrupts to CPU can be generated/cleared by software setting.
• External interrupts (8 channels)
8-channel independent operation
Interrupt source setting available : “L” to “H” edge/ “H” to “L” edge/ “L” level/ “H” level.
• 8/10-bit A/D converter (8 channels)
Conversion time : 3
μs
(at f
CP
=
32 MHz)
External trigger activation available (P50/INT0/ADTG)
Internal timer activation available (16-bit reload timer 1)
• UART(LIN/SCI) (4 channels)
Equipped with full duplex double buffer
Clock-asynchronous or clock-synchronous serial transfer is available
• CAN interface (4 channels : CAN0 and CAN2, and CAN1 and CAN3 share transmission and reception pins,
and interrupt control registers).
Conforms to CAN specifications version 2.0 Part A and B.
Automatic resend in case of error.
Automatic transfer in response to remote frame.
16 prioritized message buffers for data and ID
Multiple message support
Flexible configuration for receive filter : Full bit compare/full bit mask/two partial bit masks
Supports up to 1 Mbps
CAN wakeup function (RX connected to INT0 internally)
• LCD controller/driver (32 segment x 4 common)
Segment driver and command driver with direct LCD panel (display) drive capability
• Reset on detection of low voltage/program loop
Automatic reset when low voltage is detected
Program looping detection function
• Stepping motor controller (4 channels)
High current output for each channel
×
4
Synchronized 8/10-bit PWM for each channel
×
2
• Sound generator (2 channels)
8-bit PWM signal mixed with tone frequency from 8-bit reload counter.
PWM frequencies : 125 kHz, 62.5 kHz, 31.2 kHz, 15.6 kHz (at f
CP
=
32 MHz)
Tone frequencies : PWM frequency /2/ , divided by (reload frequency
+1)
• Input/output ports
General-purpose input/output port (CMOS output) 93 ports
• Function for port input level selection
Automotive/CMOS-Schmitt
• Flash memory security function
Protects the contents of Flash memory (Flash memory product only)
2
DS07-13750-4E
京公网安备 11010802033920号
EEWORLD
