MAX242_EAI/MAX246_EAI ................................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +165°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
CAUTION!
ESD SENSITIVE DEVICE
DC ELECTRICAL CHARACTERISTICS
(V
CC
= +2.7V to +4.8V, no RF signals applied, LNAGAIN = TXGAIN = open, VCOON = 2.4V, RXON = TXON = MOD = DIV1 = 0.45V,
PREGND = GND, T
A
= T
MIN
to T
MAX
. Typical values are at T
A
= +25°C, V
CC
= +3.3V, unless otherwise noted.) (Note 1)
PARAMETER
Supply-Voltage Range
Oscillator Supply Current
Prescaler Supply Current
(divide-by-64/65 mode) (Note 2)
Prescaler Supply Current
(buffer mode) (Note 3)
Receive Supply Current (Note 4)
Transmitter Supply Current (Note 5)
Shutdown Supply Current
Digital Input Voltage High
Digital Input Voltage Low
Digital Input Current
Note 1:
Note 2:
Note 3:
Note 4:
DIV1 = 2.4V
RXON = 2.4V, PREGND = floating
RXON = 0.45V, TXON = 2.4V, PREGND = floating
VCOON = RXON = TXON =
MOD = DIV1 = GND
T
A
= +25°C
T
A
= T
MIN
to T
MAX
2.4
0.45
±1
±10
PREGND = floating
CONDITIONS
MIN
2.7
9.5
4.2
5.4
23
26
0.5
10
TYP
MAX
4.8
14
6
8.5
36
42
UNITS
V
mA
mA
mA
mA
mA
µA
µA
V
V
µA
RXON, TXON, DIV1, VCOON, MOD
RXON, TXON, DIV1, VCOON, MOD
Voltage on any one digital input = V
CC
or GND
≥25°C
guaranteed by production test, <25°C guaranteed through correlation to worst-case temperature testing.
Calculated by measuring the combined oscillator and prescaler supply current and subtracting the oscillator supply current.
Calculated by measuring the combined oscillator and LO buffer supply current and subtracting the oscillator supply current.
Calculated by measuring the combined receive and oscillator supply current and subtracting the oscillator supply current.
With LNAGAIN = GND, the supply current drops by 4.5mA.
Note 5:
Calculated by measuring the combined transmit and oscillator supply current and subtracting the oscillator supply current.
Thanks to the above, it works after adding the op amp. Now it is switched to voltage mode, but the light is not on again. I adjusted the LED current to a very low level, and the light is on. Later, I ...
Dear experts, please help me. When I use the SPI master-slave routine of MSP430F6638, the data UCA0TXBUF of the master is indeed increasing. When I debug the slave, I find that it does not enter the U...
How long does it take to perform a multiplication operation in EVC? I used a function to measure that it takes nearly 10 microseconds, which is too time-consuming. Does anyone have any solution to the...
We are all adults, we should have some ability to distinguish right from wrong!!!This morning, when I turned on my computer, a L-shaped full-screen advertisement popped up, saying something like "360'...
Dear XDJM:At present, the FPGA section adopts a porridge forum style. I personally feel that this style cannot quickly satisfy the forum friends who come to the FPGA section to obtain or exchange info...
A machine has a word length of 32 bits and a single-word instruction. The instruction system has a number of two-address instructions, one-address instructions, and zero-address instructions (i.e., at...
In recent years, as energy consumption and environmental protection issues have attracted people's attention, my country's solar photovoltaic power generation industry has shown a rapid development...[Details]
I have read the source code of mbed these days, and the interface encapsulation for upper-level application calls is quite good. The code quality is relatively high, the comments are also very detai...[Details]
All relevant units:
In accordance with the relevant requirements of the provincial and municipal electric vehicle charging infrastructure construction work, in order to further standardize the...[Details]
Serial Port: 一. USART_ITConfig(USART1, USART_IT_TXE, ENABLE): As long as the transmit register is empty, there will always be an interrupt. Therefore, if you are not sending data, turn off the tran...[Details]
In the development of artificial intelligence, talent reserve is undoubtedly an important part. Artificial intelligence should be a bottom-level technology that can be deeply embedded in any indust...[Details]
On April 18-19, 2018, at the "Second Distributed Photovoltaic Carnival" held in Hangzhou, Jinko Power and China New Energy Assets Investment, Financing and Trading Platform (hereinafter referred to as...[Details]
As photovoltaic power stations come into people's view, people are paying more and more attention to them. Recently, some netizens asked me how to match the inverter and components of photovoltaic ...[Details]
Recently, Jiangsu GoodWe Power Technology Co., Ltd. ("GoodWe") unveiled two products of the SDT family, the 17kW smart photovoltaic inverter GW17KN-DT and the 20kW smart photovoltaic inverter GW20KN-D...[Details]
At the beginning, I used the stdlib library. Recently, I found that the cube library is more and more widely used, so I started to use the cube library to complete the ADC multi-channel acquisition e...[Details]
Today’s medical devices are filled with increasingly complex electronic devices that monitor, display, assist and warn patients. The latest generation of medical device electronic devices are smaller...[Details]
Ouster LiDAR OS-1 (left) and OS-2 (center) Velodyne invented the modern 3D LiDAR scanner in the mid-2000s, but in recent years conventional wisdom has held that Velodyne’s design — 64 lasers mounted...[Details]
Table of contents: 1 Overview 2: Common interrupt functions 3: PWM output 1 Overview In development, timers are widely used, which can be simply summarized into three aspects: 1.1: Application of ...[Details]
****************************************************************** 1. The operand is in register, R0--R7 2. Operands are in internal RAM 3. Operands are in external RAM But they are all similar. For ...[Details]
An easy programming question for microcontrollers! Urgent, write a 3-byte binary subtraction subroutine. When using the main program to call multiple groups of data for debugging, two situations need...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
