DS1803E-050 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> converter> DS1803E-050

DS1803E-050: DescriptionDigital Potentiometer ICs Addressable Dual Digital Potentiometer; CategoryAnalog mixed-signal IC converter; File Size289KB，11 Pages; ManufacturerMaxim; Websitehttps://www.maximintegrated.com/en.html

Download Datasheet Parametric View All

DS1803E-050 Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	DS1803E-050	-	-	View	Buy Now

DS1803E-050 Overview

Digital Potentiometer ICs Addressable Dual Digital Potentiometer

DS1803E-050 Parametric

Parameter Name	Attribute value
Is it lead-free?	Contains lead
Is it Rohs certified?	incompatible
Maker	Maxim
Parts packaging code	TSSOP
package instruction	TSSOP, TSSOP14,.25
Contacts	14
Reach Compliance Code	not_compliant
ECCN code	EAR99
Factory Lead Time	1 week
Other features	ALSO OPERATES FROM 5 V NOMINAL SUPPLY
Nominal bandwidth	0.2 kHz
control interface	2-WIRE SERIAL
Converter type	DIGITAL POTENTIOMETER
JESD-30 code	R-PDSO-G14
JESD-609 code	e0
length	5 mm
Humidity sensitivity level	1
Number of functions	2
Number of positions	256
Number of terminals	14
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Package body material	PLASTIC/EPOXY
encapsulated code	TSSOP
Encapsulate equivalent code	TSSOP14,.25
Package shape	RECTANGULAR
Package form	SMALL OUTLINE, THIN PROFILE, SHRINK PITCH
Peak Reflow Temperature (Celsius)	240
power supply	3/5 V
Certification status	Not Qualified
resistance law	LINEAR
Maximum resistor tolerance	20%
Maximum resistor terminal voltage	3.5 V
Minimum resistor terminal voltage	-0.5 V
Maximum seat height	1.1 mm
Nominal supply voltage	3 V
surface mount	YES
technology	CMOS
Nominal temperature coefficient	750 ppm/°C
Temperature level	INDUSTRIAL
Terminal surface	Tin/Lead (Sn/Pb)
Terminal form	GULL WING
Terminal pitch	0.65 mm
Terminal location	DUAL
Maximum time at peak reflow temperature	20
Nominal total resistance	50000 Ω
width	4.4 mm

Preview

Download Datasheet

View All

DS1803

Addressable Dual Digital Potentiometer

www.maxim-ic.com

FEATURES

3V or 5V Operation

Ultra-Low Power Consumption

Two Digitally Controlled, 256-Position

Potentiometers

14-Pin TSSOP (173 mil) and 16-Pin SO (150

mil) Packaging Available for Surface-Mount

Applications

Addressable Using 3 Address Inputs

2-Wire Serial Interface

Operating Temperature Range:

- Industrial: -40°C to +85°C

Standard Resistance Values:

- DS1803-010

10kΩ

- DS1803-050

50kΩ

- DS1803-100

100kΩ

PIN ASSIGNMENT

GND

VCC

SDA

SCL

DS1803 14-PIN TSSOP (173 MIL)

VCC

SDA

SCL

PIN DESCRIPTION

L0, L1

H0, H1

W0,W1

A0, A1, A2

SDA

SCL

GND

Low End of Resistor

High End of Resistor

Wiper terminal of Resistor

3V/5V Power Supply Input

Chip Select Inputs

Serial Data I/O

Serial Clock Input

Ground

No Connection

GND

DS1803Z 16-PIN SO (150 MIL)

DS1803 16-PIN DIP (300 MIL)

See Mech. Drawings Section on Website

DESCRIPTION

The DS1803 addressable dual digital potentiometer features two independently controlled 256-position

potentiometers. Device control is achieved through a 2-wire serial interface. Three address pins allow up

to 8 DS1803’s to share the same 2-wire interface. The exact wiper position of each potentiometer can be

written or read. The DS1803 is available in a 16-pin DIP, 16-pin SO, and 14-pin TSSOP package. The

device is available in three standard resistance values: 10kΩ, 50kΩ, and 100kΩ and is specified over the

industrial temperature range.

1 of 11

110706

DS1803

DEVICE OPERATION

The DS1803 is an addressable, digitally controlled device which has two 256-position potentiometers. A

functional block diagram of the part is shown in Figure 1. Communication and control of the device is

accomplished via a 2-wire serial interface. Address inputs A0, A1, and A2 allow up to 8 DS1803s to

share the same 2-wire interface.

Each potentiometer is composed of a 256 position resistor array. Two 8-bit registers, each assigned to a

respective potentiometer, are used to set the wiper position on the resistor array. The wiper terminal is

multiplexed to one of 256 positions on the resistor array based on its corresponding 8-bit register value.

For example, the high-end terminals, H0 and H1, have wiper position values FFh while the low-end

terminals, L0 and L1, have wiper position values 00h.

The DS1803 is a volatile device that does not maintain the position of the wiper during power-down or

loss of power. On power-up, the DS1803 wipers’ position will be set to position 00h - the low-end

terminals. The user may then set the wiper value to a desired position.

Communication with the DS1803 takes place over the 2-wire serial interface consisting of the bi-

directional pin, SDA, and the serial clock input, SCL. Complete details of the 2-wire interface are

discussed in the section entitled “2-wire Serial Data Bus.”

Application Considerations

The DS1803 is offered in three standard resistor values, which include 10kΩ, 50kΩ, and 100kΩ. The

resolution of the potentiometer is defined as R

TOT

/255, where R

TOT

is the total resistor value of the

potentiometer. The DS1803 is designed to operate using 3V or 5V power supplies over the industrial

(-40°C to +85°C) temperature range. Maximum input signal levels across the potentiometer cannot

exceed the operating power supply of the device.

2-WIRE SERIAL DATA BUS

The DS1803 supports a bi-directional 2-wire bus and data transmission protocol. A device that sends data

on the bus is defined as a transmitter, and a device receiving data as a receiver. The device that controls

the message is called a “master”. The devices that are controlled by the master are “slaves”. The bus must

be controlled by a master device which generates the serial clock (SCL), controls the bus access, and

generates the START and STOP conditions. The DS1803 operates as a slave on the 2-wire bus.

Connections to the bus are made via the open-drain I/O lines SDA and SCL.

The following bus protocol has been defined (see Figure 2).

Data transfer may be initiated only when the bus is not busy.

During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in

the data line while the clock line is high will be interpreted as control signals.

Accordingly, the following bus conditions have been defined:

Bus not busy:

Both data and clock lines remain HIGH.

Start data transfer:

A change in the state of the data line, from HIGH to LOW, while the clock is

HIGH, defines a START condition.

2 of 11

DS1803

Stop data transfer:

A change in the state of the data line, from LOW to HIGH, while the clock line is

HIGH, defines the STOP condition.

Data valid:

The state of the data line represents valid data when, after a START condition, the data line

is stable for the duration of the HIGH period of the clock signal. The data on the line must be changed

during the LOW period of the clock signal. There is one clock pulse per bit of data. Figure 2 details how

data transfer is accomplished on the 2-wire bus. Depending upon the state of the R/

* bit, two types of

data transfer are possible.

Each data transfer is initiated with a START condition and terminated with a STOP condition. The

number of data bytes transferred between START and STOP conditions is not limited, and is determined

by the master device. The information is transferred byte-wise and each receiver acknowledges with a

ninth bit.

Acknowledge:

Each receiving device, when addressed, is obliged to generate an acknowledge after the

reception of each byte. The master device must generate an extra clock pulse which is associated with this

acknowledge bit.

A device that acknowledges must pull down the SDA line during the acknowledge clock pulse in such a

way that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse. Of

course, setup and hold times must be taken into account. A master must signal an end of data to the slave

by not generating an acknowledge bit on the last byte that has been clocked out of the slave. In this case,

the slave must leave the data line HIGH to enable the master to generate the STOP condition.

Data transfer from a master transmitter to a slave receiver:

The first byte transmitted by the

master is the control byte (slave address). Next follows a number of data bytes. The slave returns an

acknowledge bit after each received byte.

Data transfer from a slave transmitter to a master receiver:

The first byte (the slave address) is

transmitted by the master. The slave then returns an acknowledge bit. Next follows a number of data

bytes transmitted by the slave to the master. The master returns an acknowledge bit after all received

bytes other than the last byte. At the end of the last received byte, a ‘not acknowledge’ is returned.

The master device generates all of the serial clock pulses and the START and STOP conditions. A

transfer is ended with a STOP condition or with a repeated START condition. Since a repeated START

condition is also the beginning of the next serial transfer, the bus will not be released.

The DS1803 may operate in the following two modes:

Slave receiver mode:

Serial data and clock are received through SDA and SCL. After each byte is

received, an acknowledge bit is transmitted. START and STOP conditions are recognized as the

beginning and end of a serial transfer. Address recognition is performed by hardware after reception

of the slave address and direction bit.

Slave transmitter mode:

The first byte is received and handled as in the slave receiver mode.

However, in this mode the direction bit will indicate that the transfer direction is reversed. Serial data

is transmitted on SDA by the DS1803 while the serial clock is input on SCL. START and STOP

conditions are recognized as the beginning and end of a serial transfer.

3 of 11

DS1803

SLAVE ADDRESS

The control byte is the first byte received following the START condition from the master device. The

control byte consists of a four bit control code; for the DS1803, this is 0101 binary. The next three bits of

the control byte are the device select bits (A2, A1, A0). They are used by the master device to select

which of the devices on the bus are to be accessed. The last bit of the control byte (R/

*) defines the

operation to be performed. When set to a one a read operation is selected, and when set to a zero a write

operation is selected. Figure 3 shows the control byte for the DS1803.

Following the START condition, the DS1803 monitors the SDA bus for the control byte being

transmitted. Upon receiving a matching control byte, the DS1803 outputs an acknowledge signal on the

SDA line.

COMMAND AND PROTOCOL

The command and protocol structure of the DS1803 allows the user to read or write the potentiometer(s).

The command structures for the part are presented in Figures 4 and 5. Data is transmitted most significant

bit (MSB) first. During communication, the receiving unit always generates the acknowledge.

Reading the DS1803

As shown in Figure 4, the DS1803 provides one read command operation. This operation allows the user

to read both potentiometers. Specifically, the R/

bit of the control byte is set equal to a 1 for a read

operation. Communication to read the DS1803 begins with a START condition which is issued by the

master device. The control byte from the master device will follow the START condition. Once the

control byte has been received by the DS1803, the part will respond with an ACKNOWLEDGE. The

bit of the control byte as stated should be set equal to ‘1’ for reading the DS1803.

When the master has received the ACKNOWLEDGE from the DS1803, the master can then begin to

receive potentiometer wiper data. The value of the potentiometer-0 wiper position will be the first

returned from the DS1803. Once the eight bits of the potentiometer-0 wiper position has been transmitted,

the master will need to issue an ACKNOWLEDGE, unless it is the only byte to be read, in which case the

master issues a NOT ACKNOWLEDGE. If desired the master may stop the communication transfer at

this point by issuing the STOP condition. However, if the value of the potentiometer-1 wiper position

value is needed, communication transfer can continue by clocking the remaining eight bits of the

potentiometer-1 value, followed by an NOT ACKNOWLEDGE. Final communication transfer is

terminated by issuing the STOP command.

Writing the DS1803

A data flow diagram for writing the DS1803 is shown in Figure 5. The DS1803 has three write

commands. These include write pot-0, write pot-1, and write pot-0/1. The write pot-0 command allows

the user to write the value of potentiometer-0 and as an option the value of potentiometer-1. The write-1

command allows the user to write the value of potentiometer-1 only. The last write command, write-0/1,

allows the user to write both potentiometers to the same value with one command and one data value

being issued.

All the write operations begin with a START condition. Following the START condition, the master

device will issue the control byte. The read/write bit of the control byte will be set to ‘0’ for writing the

DS1803. Once the control byte has been issued and the master receives the acknowledgment from the

DS1803, the command byte is transmitted to the DS1803. As mentioned above, there exist three write

4 of 11

Recommended Resources

What is the difference between linear and switching power supplies?

Intelligent digital pressure calibrator-Fluke 730G, do you know how to use it?

Simple audio sine wave generator circuit diagram

Simple series magnetic saturation AC voltage stabilization circuit

Digitally controlled gain amplifier circuit

Optical axis line on automatic grain dispensing machine

Effect of Temperature on Performance and Life of Communication Switching Power Supplies: 【Introduction】Our statistical results in practical work confirm that the main cause of data loss, hardware failure and downtime is the failure of the communication switch power supply system. The chan...; 木犯001号 Power technology

How to partition nand without eboot???: I am using uboot, how to implement nand partition, for example, part1 is for kernel and uboot, read-only; part2 is set as fat32, automatically mount. How to do it? ? Thank you...; f56007 Embedded System

Question about using internal 2.048V reference of ADS1220: Dear experts: I have a question. I use ADS1220 to design a circuit for collecting data from a resistive bridge sensor. When designing, I want to use the internal 2.048V reference as the reference volt...; xinxing Analogue and Mixed Signal

at91sam9260 mcu SD card hot swap implementation problem: [backcolor=rgb(239, 245, 249)][size=14px]Hi everyone, we are using at91sam9260 processor, and we want to implement hot-swap of SD card recently. But the information on the Internet is basically about ...; yanghelovehuang Microchip MCU

STM32 Technical Reference Manual Chinese Translation 10th Edition: The following is the "STM32 Technical Reference Manual Chinese Translation 10th Edition", I hope it will be helpful to you...; svfya stm32/stm8

Error when installing CCS6.2: After downloading CCS6.2.0.00048_win32 from the official website, unzipping it, and running ccs_setup_6.2.0.00048.exe, the following screen appears:How can I solve this problem? ? Win10 system needs g...; 写程序8 Analogue and Mixed Signal

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components