The MAX6477–MAX6484 are constructed using a unique set of packaging techniques that impose a limit on the thermal pro-
file the devices can be exposed to during board-level solder attach and rework. This limit permits only the use of the solder
profiles recommended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and
Convection reflow. Pre-heating is required. Hand or wave soldering is not allowed.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
IN
= (V
OUT
+ 0.5V) or +2.5V, whichever is greater, C
OUT
= 3.3µF, T
A
= -40°C to +85°C. Typical specifications are at T
A
= +25°C,
unless otherwise noted.) (Note 2)
PARAMETER
Input Voltage Range
Input Undervoltage Lockout
Supply Current (Ground Current)
Shutdown Supply Current
REGULATOR CIRCUIT
Output Current
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6469–MAX6476
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6477–MAX6484
Adjustable Output Voltage Range
SET Reference Voltage
SET Dual Mode
TM
Threshold
SET Input Leakage Current
1mA
≤
I
OUT
≤
150mA, T
A
= +25°C
1mA
≤
I
OUT
≤
150mA, T
A
= -40°C to +85°C
1mA
≤
I
OUT
≤
300mA, T
A
= -40°C to +85°C
2mA
≤
I
OUT
≤
100mA, T
A
= +25°C
2mA
≤
I
OUT
≤
100mA, T
A
= -40°C to +85°C
2mA
≤
I
OUT
≤
300mA, T
A
= -40°C to +85°C
(Note 3)
V
SET
I
SET
V
SET
= 0V, +1.2V (Note 3)
SYMBOL
V
IN
V
UVLO
I
Q
I
SHDN
V
IN
falling
I
OUT
= 0A
I
OUT
= 300mA
T
A
= +25°C
300
-1.3
-2.3
-2.7
-1.1
-2.0
-2.5
V
SET
1.200
CONDITIONS
MIN
2.5
2.25
82
96
0.1
TYP
MAX
5.5
2.47
136
1
UNITS
V
V
µA
µA
mA
+1.3
+2.3
+2.7
+1.1
+2.0
+2.5
5.0
1.258
±100
V
V
mV
nA
%
%
1.229
185
±20
Dual Mode is a trademark of Maxim Integrated Products, Inc.
Drivers often need to send log information to applications at irregular intervals, and applications are responsible for displaying it to users. I can think of two ways to achieve this: one is that the...
Function introduction: ○ The programming software is compatible with Japan's Mitsubishi FXGP_WIN-C ladder diagram software, which is equivalent to Mitsubishi's FX1N in application; ○ The working power...
I started to get in touch with DSP. At the beginning, I didn’t know anything and learned from each other. The laboratory has test chambers of models such as DM642 and 5509A. The DM642 has a camera and...
Lite FET-Pro430 Elprotronic is a mass production download tool for MSP430. After installing it last Friday, the MSP-FET430UIF cannot be downloaded for simulation. What's going on?...
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
1 Introduction
A wide variety of communication cables and control cables are widely used in various instruments and control equipment. Whether the cable is well-conducted and
whether
th...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
MediaTek (2454) announced the acquisition of F-MStar (3697) and attracted the attention of IC design industry. This morning, Gartner Semiconductor Industry Research Director Hong Cenwei analyzed ...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
Introduction
X1226 has the functions of clock and calendar. The clock relies on hour, minute and second registers to track, and the calendar relies on date, week, month and year registers to tr...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
In order to develop lighting LED technology, developed countries attach great importance to the research of LED testing methods and standards. For example, the National Institute of Standards and T...[Details]
Currently, the commonly used solar cell technologies include monocrystalline silicon solar cells and polycrystalline silicon thin-film solar cells. Production process: Monocrystalline silicon solar...[Details]
The production process of lithium batteries does not mention the previous processes such as material preparation, winding, liquid injection, and packaging, but only talks about the final formation ...[Details]
With the popularity of digital appliances, rechargeable batteries can be seen everywhere in people's daily lives and have become one of the indispensable daily necessities.
This article gives ...[Details]
0 Introduction
PROFIBUS is an open digital communication system with a wide range of applications, which has been included in the international standards IEC 61158 and IEC 61784. Since the gen...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
