Input voltages may exceed the supply voltages, provided the input current is limited to ±100µA.
Note 2:
Dissipation rating assumes device is mounted with all leads soldered to the PCB.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(Note 3)
PARAMETER
Zero Input Reading
Ratiometric Reading
CONDITIONS
V
IN
= 0V, full scale = 200.0mV
V
IN
= V
REF
, V
REF
= 100mV
MIN
-000.0
999
TYP
000.0
MAX
+000.0
UNITS
Digital
Reading
Digital
Reading
Counts
999/1000 1000
Rollover Error (Difference in Reading for
Equal Positive and Negative Reading Near -V
IN
= +V
IN
= 200.0mV
Full Scale)
Linearity (Maximum Deviation from Best
Straight Line Fit)
Common-Mode Rejection Ratio (Note 4)
Noise (Pk-Pk Value Not Exceeded
95% of Time)
Input Leakage Current
Zero Reading Drift
Scale Factor Temperature Coefficient
Full scale = 200mV or full scale = 2.000V
V
CM
=
Q1V,
V
IN
= 0V, full scale = 200.0mV
V
IN
= 0V, full scale = 200mV
V
IN
= 0V
V
IN
= 0V, 0NC < T
A
< +70NC
V
IN
= 199.0mV, 0NC < T
A
< +70NC
(external reference 0ppm/NC)
-1
Q2
+1
-1
Q2
50
15
1
0.2
1
0.8
0.6
+1
Counts
FV/V
FV
10
1
5
1.8
1.8
3.2
pA
FV/NC
ppm/NC
mA
mA
V
ppm/NC
V+ Supply Current (Does Not Include LED
V
IN
= 0V
Current for ICL7107)
V- Supply Current (ICL7107 Only)
Analog Common Voltage
(With Respect to Positive Supply)
25kI between common and positive supply
2.4
2.8
80
Temperature Coefficient of Analog
25kI between common and positive supply
Common (With Respect to Positive Supply)
The electrical characteristics above are a reproduction of a portion of Intersil's copyrighted (1983/1984) data book. This information
does not constitute any representation by Maxim that Intersil's products will perform in accordance with these specifications. The
"Electrical Characteristics table" along with the descriptive excerpts from the original manufacturer's data sheet have been included
in this data sheet solely for comparative purposes.
2
Maxim Integrated
ICL7106/ICL7107
3
1
⁄
2
Digit A/D Converters
ELECTRICAL CHARACTERISTICS (continued)
(Note 3)
PARAMETER
ICL7106 Only
Pk-Pk Segment Drive Voltage,
Pk-Pk Backplane Drive Voltage (Note 5)
ICL7107 Only
Segment Sinking Current
V
+
to V
-
= 9V
(Except pin 19) V
+
= 5.0V, segment voltage = 3V
Pin 19
o
nly
CONDITIONS
MIN
4
5
10
TYP
5
8.0
16
MAX
6
UNITS
V
mA
Note 3:
Unless otherwise noted, specifications apply to both the ICL7106 and ICL7107 at T
A
= +25NC, f
CLOCK
= 48kHz. ICL7106
is tested in the circuit of Figure 1. ICL7107 is tested in the circuit of Figure 2.
Note 4:
See the
Differential Input
section.
Note 5:
Backplane drive is in phase with segment drive for “off” segment, 180N out of phase for “on” segment. Frequency is 20
times the conversion rate. Average DC component is less than 50mV.
京公网安备 11010802033920号
EEWORLD
