Halogen and Antimony Free. “Green” Device (Note 3)
Qualified to AEC-Q100 Grade 1
PPAP Capable (Note 4)
(Top View)
1OUT
2OUT
1
2
3
4
5
-
2
4
14
3OUT
13
4OUT
12
GND
11
4IN+
10
4IN-
9
8
3IN+
3IN-
+
V
CC
2IN-
2IN+
1IN-
-
+
1
3
+
6
1IN+
7
-
+
-
SO-14/TSSOP-14
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green"
and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.
4. Automotive products are AEC-Q100 qualified and are PPAP capable. Refer http://www.diodes.com/quality/product_compliance_definitions/.
Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will
also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.
All limits are guaranteed by testing or statistical analysis. Limits over the full temperature (-40 ≤ T
A
≤ +125°C) are guaranteed by design, but not tested in
production.
V
O
1.4V, R
S
= 0Ω with V
CC
from 5V to 30V.
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output
so no loading change exists on the input lines.
The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (@ +25°C). The upper end of the
common-mode voltage range is V
CC
-1.5V (@ +25°C), but either or both inputs can go to +36V without damage, independent of the magnitude of V
CC
.
The response time specified is for a 100mV step input with 5mV overdrive. For larger overdrive signals 300ns can be obtained, see typical performance
characteristics.
Positive excursions of input voltage may exceed the power supply level. As long as other voltages remain within the common mode range, the
comparator will provide a proper output stage. The low voltage state must not be less than -0.3V (or 0.3V below the magnitude of the negative power
Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will
also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material
All limits are guaranteed by testing or statistical analysis. Limits over the full temperature (-40
≤
T
A
≤
+125°C) are guaranteed by design, but not tested
in production.
V
O
1.4V, R
S
= 0Ω with V
CC
from 5V to 30V.
The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output
so no loading change exists on the input lines.
The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (@ +25°C). The upper end of the
common-mode voltage range is V
CC
-1.5V (@ +25°C), but either or both inputs can go to +36V without damage, independent of the magnitude of V
CC
.
The response time specified is for a 100mV step input with 5mV overdrive. For larger overdrive signals 300ns can be obtained, see typical performance
characteristics.
Positive excursions of input voltage may exceed the power supply level. As long as other voltages remain within the common-mode range, the
comparator will provide a proper output stage. The low voltage state must not be less than -0.3V (or 0.3V below the magnitude of the negative power
京公网安备 11010802033920号
EEWORLD
