performance oscillators utilize a proven silicon MEMS
technology to provide excellent jitter and stability over
a wide range of supply voltages and temperatures. By
eliminating the need for quartz or SAW technology,
MEMS oscillators significantly enhance reliability and
accelerate product development, while meeting
stringent clock performance criteria for a variety of
communications, storage, and networking applications.
DSC1101 has a standby feature that allows it to
completely power-down when EN pin is pulled low;
whereas for DSC1121, only the outputs are disabled
when EN is low. Both oscillators are available in
industry standard packages, including the small
2.5 mm x 2.0 mm, and are “drop-in” replacements for
standard 4-pin CMOS quartz crystal oscillators.
Functional Block Diagram
Applications
• Storage Area Networks
- SATA, SAS, Fibre Channel
• Passive Optical Networks
- EPON, 10G-EPON,V GPON, 10G-PON
• Ethernet
- 1G, 10GBASE-T/KR/LR/SR, and FCoE
• HD/SD/SDI Video and Surveillance
• PCI Express
• Display Port
2017 Microchip Technology Inc.
DS20005613B-page 1
DSC1101/21
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
Input Voltage, V
IN
..............................................................................................................................–0.3V to V
DD
+ 0.3V
Supply Voltage .......................................................................................................................................... –0.3V to +4.0V
ESD Protection On All Pins ........................................................................................... 4000V HBM, 1500V CDM (max.)
† Notice:
Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Note:
1000+ years of data retention on internal memory.
TABLE 1-1:
DC CHARACTERISTICS
Electrical Characteristics
Parameters
Supply Voltage (Note
1)
Sym.
V
DD
Min.
2.25
—
Supply Current
I
DD
—
—
Frequency Stability
(Including frequency
variations due to initial
tolerance, temp. and
power supply voltage.)
Aging
Startup Time (Note
2)
Input Logic Levels
Input Logic High
Input Logic Low
Output Disable Time
(Note
3)
Output Enable Time
Enable Pull-up Resistor
(Note
4)
CMOS Output
Output Logic Levels
Output Logic High
Output Logic Low
Note 1:
2:
3:
4:
V
OH
V
OL
0.9
V
DD
—
—
—
—
0.1
V
DD
V
I = ±6 mA
—
Typ.
—
—
20
31
—
—
—
—
—
—
—
—
—
—
40
Max.
3.6
0.095
22
35
±10
±20
—
—
—
—
0.75
V
DD
—
—
—
—
—
±25
±50
±5
5
—
0.1
V
DD
5
5
20
—
V
ns
ms
ns
k
—
—
DSC1101
DSC1121
Pull-up Resistor Exist
ppm
ms
ppm
mA
Units
V
—
DSC1101, EN pin low, output
is disabled
DSC1121, EN pin low, output
is disabled
Output enabled, C
L
= 15 pF,
F
0
= 100 MHz
Ext Comm. & Ind. only
All temp ranges
All temp ranges
All temp ranges
1 year @ 25°C
T = 25°C
Conditions
f
f
t
SU
V
IH
V
IL
t
DS
t
EN
—
Pin 6 V
DD
should be filtered with 0.1 µF capacitor.
t
SU
is time to 100 ppm of output frequency after V
DD
is applied and outputs are enabled.
Output Waveform and Test Circuit figures define the parameters.
Output is enabled if pad is floated or not connected.
DS20005613B-page 2
2017 Microchip Technology Inc.
DSC1101/21
TABLE 1-1:
DC CHARACTERISTICS (CONTINUED)
Electrical Characteristics
Parameters
Output Transition Time
Rise Time
Fall Time
Sym.
t
R
t
F
Min.
—
—
2.3
Frequency
f
0
3.3
Output Duty Cycle
Period Jitter
Integrated Phase Noise
SYM
J
PER
J
PH
45
—
—
—
—
Note 1:
2:
3:
4:
—
—
3
0.3
0.38
1.7
170
55
—
—
—
2
ps
RMS
%
ps
RMS
Typ.
1.1
1.3
—
Max.
2
2
170
MHz
ns
Units
Conditions
20% to 80%
C
L
= 15 pF
C
L
= 15 pF, –20°C to +70°C
and –40°C to +85°C
C
L
= 15 pF, –40°C to +105°C
and –55°C to +125°C
—
F
OUT
= 125 MHz
200 kHz to 20 MHz @ 125 MHz
100 kHz to 20 MHz @ 125 MHz
12 kHz to 20 MHz @ 125 MHz
Pin 6 V
DD
should be filtered with 0.1 µF capacitor.
t
SU
is time to 100 ppm of output frequency after V
DD
is applied and outputs are enabled.
Output Waveform and Test Circuit figures define the parameters.
Output is enabled if pad is floated or not connected.
2017 Microchip Technology Inc.
DS20005613B-page 3
DSC1101/21
TEMPERATURE SPECIFICATIONS (Note
1)
Parameters
Temperature Ranges
T
A
Operating Temperature Range (T)
T
A
T
A
T
A
Junction Operating Temperature
Storage Temperature Range
Soldering Temperature Range
Note 1:
T
J
T
A
T
S
–20
–40
–40
–55
—
–40
—
—
—
—
—
—
—
—
+70
+85
+105
+125
+150
+150
+260
°C
°C
°C
°C
°C
°C
°C
Ordering Option E
Ordering Option I
Ordering Option L
Ordering Option M
—
—
40 sec. max
Sym.
Min.
Typ.
Max.
Units
Conditions
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
junction temperature and the thermal resistance from junction to air (i.e., T
A
, T
J
,
JA
). Exceeding the
maximum allowable power dissipation will cause the device operating junction temperature to exceed the
maximum +125°C rating. Sustained junction temperatures above +125°C can impact the device reliability.
DS20005613B-page 4
2017 Microchip Technology Inc.
DSC1101/21
2.0
Note:
NOMINAL PERFORMANCE CURVES
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
[p=30, 2, left]Why do many novices still fail to get started? Why do so many people find FPGA difficult to learn? I will post a thread to explain in detail the reasons why novices find FPGA difficult ...
ONVIF officially released the latest version of ONVIF protocol test tool, ONVIF Device test Tool V12.12[/color][/size] [size=4][color=#0000ff] [/color][/size][size=4][color=#0000ff] [/color][/size] [s...
[align=center][/align] A few days ago, we discussed "[url=https://bbs.eeworld.com.cn/thread-557696-1-1.html]Can electric cars replace gasoline cars in ten years?". [/b][/font] I have been thinking the...
I used evc to write a serial port test program. The acquisition device I used sent data to the industrial control board at a data rate of about 10k/s. No matter I used waitcommevent or readfile serial...
Today I saw a joke about answering questions in class. Let me tell you about my personal experience. I remember it was when I was in the second grade of junior high school. Let me explain: it was all ...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:00[/i] [table][tr][td][color=#808080][/color][/td][/tr][tr][td] Ceramics that can utilize electrical and magnetic properties in the ele...
Abstract:
With the increasing complexity of smart vehicle electrical and electronic architectures, the full lifecycle management of vehicle electronic control components faces multiple challe...[Details]
As the main model among new energy vehicles, pure electric vehicles have received strong support and encouragement from the country in recent years, and their development is changing with each pass...[Details]
In recent years, the government has increasingly supported electric vehicles, and the number of electric vehicles has increased. Observant drivers will notice that there are many more green license...[Details]
Limited vocabulary recognition
According to the number of characters, words or short sentences in the vocabulary, it can be roughly divided into: less than 100 is small vocabulary; 100-1000 is...[Details]
For healthcare professionals, accurate diagnosis and treatment are crucial for a clear picture of a person's health. However, healthcare professionals often rely on tests at medical facilities, cli...[Details]
Definition of interactive projection system:
Interactive projection systems, also known as multimedia interactive projection, are available in floor, wall, and tabletop interactive projection....[Details]
Gross profit margin jumped from 13.6% in the first half of last year to 25.9%, almost doubling year-on-year.
On August 21, RoboSense released its interim performance report, in which the...[Details]
On August 22, South Korean media Nate reported on the 20th local time that Samsung Electronics is introducing Hyper Cell technology into its most advanced 2nm process technology, striving to improv...[Details]
introduction
The concept of the smart home is gradually developing and gaining market acceptance. We believe its ultimate form lies in the interconnection of all home appliances through open i...[Details]
PowiGaN achieves 95% efficiency at both light and full loads, meeting critical operational and safety requirements.
DARWIN, Australia and SAN JOSE, Calif.,
August 22, 2025 – Powe...[Details]
Recently, Joyson Electronics has made positive progress in the core technology research and development of the robot's "brain and brain" and key components, and launched the industry's first integr...[Details]
Methods of DC motor speed regulation:
1. The voltage regulator can be used to change the input voltage and speed directly, which is often used for large kilowatt-level motors.
2. Thyristo...[Details]
Previously, Positive Motion Technology shared with you the firmware upgrade of motion controller, ZBasic program development, ZPLC program development, communication with touch screen and input/out...[Details]
There are more and more electric vehicles. Recently, I have heard some news about electric vehicles performing poorly in winter. I would like to briefly introduce whether heat pump technology is mo...[Details]
As the range of electric vehicles continues to increase, driving electric vehicles for long-distance travel has become a trend. For high-speed travel, how much impact will high-speed driving of ele...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
