Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice.
IDT72V3613 3.3V, CMOS CLOCKED FIFO WITH
BUS-MATCHING AND BYTE SWAPPING 64 x 36
COMMERCIAL TEMPERATURE RANGE
DESCRIPTION (CONTINUED)
36-bit mailbox registers. Each mailbox register has a flag to signal when new
mail has been stored. Parity is checked passively on each port and may be
ignored if not desired. Parity generation can be selected for data read from each
port. Two or more devices may be used in parallel to create wider data paths.
The IDT72V3613 is a synchronous (clocked) FIFO, meaning each port
employs a synchronous interface. All data transfers through a port are gated
to the LOW-to-HIGH transition of a continuous (free-running) port clock by
enable signals. The continuous clocks for each port are independent of one
another and can be asynchronous or coincident. The enables for each port are
arranged to provide a simple interface between microprocessors and/or buses
with synchronous interfaces.
The Full Flag (FF) and Almost-Full (AF) flag of the FIFO are two-stage
synchronized to the port clock (CLKA) that writes data into its array. The Empty
Flag (EF) and Almost-Empty (AE) flag of the FIFO are two-stage synchronized
to the port clock (CLKB) that reads data from its array.
The IDT72V3613 is characterized for operation from 0°C to 70°C. This
device is fabricated using high speed, submicron CMOS technology.
PIN CONFIGURATION
A
24
A
25
A
26
V
CC
A
27
A
28
A
29
GND
A
30
A
31
A
32
A
33
A
34
A
35
GND
B
35
B
34
B
33
B
32
B
31
B
30
GND
B
29
B
28
B
27
V
CC
B
26
B
25
B
24
B
23
A
23
A
22
A
21
GND
A
20
A
19
A
18
A
17
A
16
A
15
A
14
A
13
A
12
A
11
A
10
GND
A
9
A
8
A
7
V
CC
A
6
A
5
A
4
A
3
GND
A
2
A
1
A
0
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
B
22
B
21
GND
B
20
B
19
B
18
B
17
B
16
B
15
B
14
B
13
B
12
B
11
B
10
GND
B
9
B
8
B
7
V
CC
B
6
B
5
B
4
B
3
GND
B
2
B
1
B
0
EF
AE
NC
AF
FF
CSA
ENA
CLKA
W/RA
V
CC
PGA
PEFA
MBF2
MBA
FS
1
FS
0
ODD/EVEN
RST
GND
BE
SW1
SW0
SIZ1
SIZ0
MBF1
PEFB
PGB
V
CC
W/RB
CLKB
ENB
CSB
NC
TQFP (PNG120, order code: PF)
TOP VIEW
2
NOTES:
1. Pin 1 idenifier in corner.
2. NC = No internal connection
4661 drw 02
IDT72V3613 3.3V, CMOS CLOCKED FIFO WITH
BUS-MATCHING AND BYTE SWAPPING 64 x 36
COMMERCIAL TEMPERATURE RANGE
PIN DESCRIPTION
Symbol
A
0
-A
35
AE
AF
B
0
-B
35
BE
CLKA
CLKB
Name
Port A Data
Almost-Empty Flag
Almost-Full Flag
Port B Data
Big-Endian Select
Port A Clock
Port B Clock
I/O
I/O
O
Port B
O
Port A
I/O
I
I
I
36-bit bidirectional data port for side A.
Programmable Almost-Empty flag synchronized to CLKB. It is LOW when Port B the number of 36-bit
words in the FIFO is less than or equal to the value in the offset register, X.
Programmable Almost-Full flag synchronized to CLKA. It is LOW when the number of 36-bit empty
empty locations in the FIFO is less than or equal to the value in the offset register, X.
36-bit bidirectional data port for side B
Selects the bytes on port B used during byte or word FIFO reads. A LOW on
BE
selects the most
significant bytes on B0-B35 for use, and a HIGH selects the least significant bytes.
CLKA is a continuous clock that synchronizes all data transfers through port A and can be asynchronous
or coincident to CLKB.
FF
and
AF
are synchronized to the LOW-to-HIGH transition of CLKA.
CLKB is a continuous clock that synchronizes all data transfers through port B and can be asynchronous
or coincident to CLKA. Port-B byte swapping and data port sizing operations are also synchronous to the
LOW-to-HIGH transition of CLKB.
EF
and
AE
are synchronized to the LOW-to-HIGH transition of CLKB.
CSA
must be LOW to enable a LOW-to-HIGH transition of CLKA to read or write data on port A. The A0-
A35 outputs are in the high-impedance state when
CSA
is HIGH.
CSB
must be LOW to enable a LOW-to-HIGH transition of CLKB to read or write data on port B. The B0-
B35 outputs are in the high-impedance state when
CSB
is HIGH.
EF
is synchronized to the LOW-to-HIGH transition of CLKB. When
EF
is LOW, the FIFO is empty, and
reads from its memory are disabled. Data can be read from the FIFO to its output register when
EF
is
HIGH.
EF
is forced LOW when the device is reset and is set HIGH by the second LOW-to-HIGH
transition of CLKB after data is loaded into empty FIFO memory.
ENA must be HIGH to enable a LOW-to-HIGH transition of CLKA to read or write data on port A.
ENB must be HIGH to enable a LOW-to-HIGH transition of CLKB to read or write data on port B.
FF
is synchronized to the LOW-to-HIGH transition of CLKA. When
FF
is LOW, the FIFO is full, and
writes to its memory are disabled.
FF
is forced LOW when the device is reset and is set HIGH by the
second LOW-to-HIGH transition of CLKA after reset.
The LOW-to-HIGH transition of
RST
latches the values of FS0 and FS1, which loads one of four preset
values into the Almost-Full flag and Almost-Empty flag offsets.
A high level on MBA chooses a mailbox register for a port A read or write operation. When the A0-A35
outputs are active, mail2 register data is output.
MBF1
is set LOW by a LOW-to-HIGH transition of CLKA that writes data to the mail1 register. Writes to the
mail1 register are inhibited while
MBF1
is set LOW.
MBF1
is set HIGH by a LOW-to-HIGH transition of
CLKB when a port B read is selected and both SIZ1 and SIZ0 are HIGH.
MBF1
is set HIGH when the
device is reset.
MBF2
is set LOW by a LOW-to-HIGH transition of CLKB that writes data to the mail2 register. Writes to the
mail2 register are inhibited while
MBF2
is set LOW.
MBF2
is set HIGH by a LOW-to-HIGH transition of
CLKA when a port A read is selected and MBA is HIGH.
MBF2
is set HIGH when the device is reset.
Odd parity is checked on each port when ODD/EVEN is HIGH, and even parity is checked when
ODD/EVEN is LOW. ODD/EVEN also selects the type of parity generated for each port if parity
generation is enabled for a read operation.
When any valid byte applied to terminals A0-A35 fails parity,
PEFA
is LOW. Bytes (Port A) are organized
as A0-A8, A9-A17, A18-A26, and A27-A35, with the most significant bit of each byte serving as the parity
bit. The type of parity checked is determined by the state of the ODD/EVEN input.
The parity trees used to check the A0-A35 inputs are shared by the mail2 register to generate parity if
parity generation is selected by PGA. Therefore, if a mail2 read with parity generation is set up by having
CSA
LOW, ENA HIGH, W/RA LOW, MBA HIGH and PGA HIGH, the
PEFA
flag is forced HIGH
regardless of the state of the A0-A35 inputs.
Description
CSA
CSB
EF
Port A Chip Select
Port B Chip Select
Empty Flag
I
I
O
Port B
ENA
ENB
FF
Port A Enable
Port B Enable
Full Flag
I
I
O
Port A
I
I
O
FS
1
, FS
0
Flag Offset Selects
MBA
MBF1
Port A Mailbox
Select
Mail1 Register Flag
MBF2
Mail2 Register Flag
O
ODD/
EVEN
PEFA
Odd/Even Parity
Select
Port A Parity Error
Flag
I
O
3
IDT72V3613 3.3V, CMOS CLOCKED FIFO WITH
BUS-MATCHING AND BYTE SWAPPING 64 x 36
COMMERCIAL TEMPERATURE RANGE
PIN DESCRIPTION (CONTINUED)
Symbol
PEFB
Name
Port B Parity Error
Flag
I/O
Description
O
When any valid byte applied to terminals B0-B35 fails parity,
PEFB
is LOW. Bytes are organized as
(Port B) B0-B8, B9-B17, B-18-B26, and B27-B35, with the most significant bit of each byte serving as the parity
bit. A byte is valid when it is used by the bus size selected for port B. The type of parity checked is
determined by the state of the ODD/EVEN input.
The parity trees used to check the B0-B35 inputs are shared by the mail1 register to generate parity if
parity generation is selected by PGB. Therefore, if a mail1 read with parity generation is set up by having
CSB
LOW, ENB HIGH, W/RB LOW, SIZ1 and SIZ0 HIGH and PGB HIGH, the
PEFB
flag is forced HIGH
regardless of the state of the B0-B35 inputs.
PGA
Port A Parity
Generation
Port B Parity
Generation
Reset
I
Parity is generated for data reads from the mail2 register when PGA is HIGH. The type of parity
generated is selected by the state of the ODD/EVEN input. Bytes are organized at A0-A8, A9-A17, A18-
A26, and A27-A35. The generated parity bits are output in the most significant bit of each byte.
Parity is generated for data reads from port B when PGB is HIGH. The type of parity generated is
selected by the state of the ODD/EVEN input. Bytes are organized as B0-B8, B9-B17, B18-B26, and
B27-B35. The generated parity bits are output in the most significant bit of each byte.
To reset the device, four LOW-to-HIGH transitions of CLKA and four LOW-to-HIGH transitions of CLKB
must occur while
RST
is LOW. This sets the
AF, MBF1,
and
MBF2
flags HIGH and the
EF, AE,
and
FF
flags LOW. The LOW-to-HIGH transition of
RST
latches the status of the FS1 and FS0 inputs to select
Almost-Full flag and Almost-Empty flag offset.
PGB
I
RST
I
SIZ0,
SIZ1
Port B Bus Size
Selects
I
A LOW-to-HIGH transition of CLKB latches the states of SIZ0, SIZ1, and
BE,
and the following LOW-to-
(Port B) HIGH transition of CLKB implements the latched states as a port B bus size. Port B bus sizes can be long
word, word, or byte. A HIGH on both SIZ0 and SIZ1 chooses a mailbox register for a port B 36-bit write or
read.
I
At the beginning of each long word FIFO read, one of four modes of byte-order swapping is selected by
(Port B) SW0 and SW1. The four modes are no swap, byte swap, word swap, and byte-word swap. Byte-order
swapping is possible with any bus-size selection.
I
I
A HIGH selects a write operation and a LOW selects a read operation on port A for a LOW-to-HIGH
transition of CLKA. The A0-A35 outputs are in the high-impedance state when W/RA is HIGH.
A HIGH selects a write operation and a LOW selects a read operation on port B for a LOW-to-HIGH
transition of CLKB. The B0-B35 outputs are in the high-impedance state when W/RB is HIGH.
SW0,
SW1
W/RA
W/RB
Port B Byte Swap
Selects
Port A Write/Read
Select
Port B Write/Read
Select
4
IDT72V3613 3.3V, CMOS CLOCKED FIFO WITH
BUS-MATCHING AND BYTE SWAPPING 64 x 36
COMMERCIAL TEMPERATURE RANGE
ABSOLUTE MAXIMUM RATINGS OVER OPERATING FREE-AIR TEMPERATURE
RANGE (unless otherwise noted)
(1)
Symbol
V
CC
V
I
(2)
V
O
(2)
I
IK
I
OK
I
OUT
I
CC
T
STG
Supply Voltage Range
Input Voltage Range
Output Voltage Range
Input Clamp Current, (V
I
< 0 or V
I
> V
CC
)
Output Clamp Current, (V
O
< 0 or V
O
> V
CC
)
Continuous Output Current, (V
O
= 0 to V
CC
)
Continuous Current Through V
CC
or GND
Storage Temperature Range
Rating
Commercial
–0.5 to +4.6
–0.5 to V
CC
+0.5
–0.5 to V
CC
+0.5
±20
±50
±50
±500
–65 to 150
Unit
V
V
V
mA
mA
mA
mA
°
C
NOTES:
1. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the
device at these or any other conditions beyond those indicated under "Recommended Operating Conditions" is not implied. Exposure to absolute-maximum-rated conditions
for extended periods may affect device reliability.
2. The input and output voltage ratings may be exceeded provided the input and output current ratings are observed.
RECOMMENDED OPERATING
CONDITIONS
Symbol
V
CC
V
IH
V
IL
I
OH
I
OL
T
A
Parameter
Supply Voltage
HIGH Level Input Voltage
LOW-Level Input Voltage
HIGH-Level Output Current
LOW-Level Output Current
Operating Free-air
Temperature
Min. Typ.
3.0
2
—
—
—
0
3.3
—
—
—
—
—
Max.
3.6
V
CC
+0.5
0.8
–4
8
70
Unit
V
V
V
mA
mA
°
C
ELECTRICAL CHARACTERISTICS OVER RECOMMENDED OPERATING
FREE-AIR TEMPERATURE RANGE (unless otherwise noted)
PIC16F73's PORTA can be used as an analog input port. Is it an analog port or a digital I/O when the power is first turned on? If ACDON1 is used to set it as an analog input port, how can it be change...
The program uses UART interrupt and 485 to send commands and receive data. Two arrays are defined to store commands and receive data. This is the first time I encounter this error. What does it mean?...
Preparation:1. Modify Flash2833x_API_Config.h to adapt to your target operation status
2. Add Flash2833x_API_Library.h to the code
3. Add the Flash API library to the project
Own application:4. Initia...
At present, the development of wireless power supply technology for electric vehicles (EVs) is becoming more and more active. In 2012, Volvo of Sweden established Volvo Technology Japan in Tokyo as...[Details]
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
Automotive applications are particularly sensitive to EMI events, which are unavoidable in a noisy electrical environment consisting of a central battery, bundled wiring harnesses, various inductiv...[Details]
In order to highlight the concept of "energy saving and environmental protection" of intelligent buildings, solar street lights are designed for intelligent communities. The inclination and capacit...[Details]
Although it is relatively easy to check the stability of a simple amplifier at lower frequencies, it may be much more difficult to evaluate the stability of a more complex circuit. This artic...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
Against the backdrop of global warming, energy conservation and emission reduction have become a global hotspot and focus, which has also sounded the clarion call for the take-off of the LED lighti...[Details]
a. Keep the battery clean, wipe off the spilled electrolyte, contaminated dirt and dust in time; keep the poles and terminal clamps clean and in good contact, and apply vaseline or butter to preven...[Details]
Nowadays, more and more people have digital cameras. The convenience and speed of digital cameras have gradually replaced film cameras and become the main tool for people's daily photography. The n...[Details]
1 Introduction
Washing machines are an indispensable household appliance in the home, and they are developing very fast. Fully automatic washing machines are favored by everyone because of their con...[Details]
1 Introduction
At present, advocating health has become the focus of people's attention, and the emergence of treadmills has become more and more popular. People can exercise at home or in the ...[Details]
As a type of iron battery, lithium iron phosphate battery (hereinafter referred to as lithium iron battery) has always been widely concerned by industry friends (some people say that lithium iron b...[Details]
1 Introduction
The coke oven gas recovery system is mainly composed of a gas tank and a pressure reducing station. While realizing the recycling and reuse of coke oven gas, it also plays an imp...[Details]
The NCL30051 from On Semi is a peak current controlled fixed off time buck controller designed for LED driver applications. It has adjustable off time, 250mA source/500mA sink peak drive capability, ±...[Details]
Microchip MCU
京公网安备 11010802033920号
EEWORLD
