Absolute Maximum Ratings (Unless otherwise specified, Tj=25°C)
Inverter Part
Item
Symbol
Ratings
Unit
Supply Voltage
Supply Voltage(Surge)
Collector-Emitter Voltage
Collector Current
DC
PEAK
V
P
V
P(surge)
V
CES
I
C
I
CP
P
C
T
jmax
450
500
600
±15
±30
(Note 1)
(Note 1)
Conditions
Applied between P-NU,NV,NW
Applied between P-NU,NV,NW
T
C
=25°C
T
C
=25°C, less than 1ms
T
C
=25°C, per 1 chip
V
V
V
A
A
W
°C
Collector Power Dissipation
Junction Temperature
(Note 1) Do not, however exceed P
C
, ASO.
41
150
Control part
Item
Control Power Supply
Floating Control Power Supply
Control Input Voltage
Fault Output Supply Voltage
Fault Output Current
Current Sensing Input Voltage
Bootstrap diode part
Item
Reverse Voltage
Junction Temperature
Total system
Item
Self Protection Supply Voltage
(SCP Capability)
Module Case Temperature
Storage Temperature
Isolation Voltage
Symbol
V
P(PROT)
T
C
T
stg
V
iso
Ratings
400
-25 to +100
-40 to +125
1500
Unit
V
°C
°C
V
rms
Sinusoidal, 60Hz, AC 1minute,
between connected all pins and heat sink
plate
Conditions
V
CC
=13.5 to 16.5V, Inverter part
T
j
=125°C, non-repetitive, less than 2µs
Measurement point of T
C
is provided
in Figure 2
Symbol
V
CC
V
BS
V
IN
V
FO
I
FO
V
CIN
Ratings
20
20
-0.5 to V
CC
+0.5
-0.5 to V
CC
+0.5
1
-0.5 to +7.0
Unit
V
V
V
V
mA
V
Conditions
Applied between HVCC-GND, LVCC-GND
Applied between VBU-U, VBV-V, VBW-W
Applied between HINX, LINX-GND
(X=U,V,W)
Applied between FO-GND
Sink current at FO pin
Applied between CIN-GND
Symbol
V
RB
T
jmaxD
Ratings
600
150
Unit
V
°C
Conditions
Thermal resistance
Item
Junction to Case Thermal
Resistance
(Note 2)
Symbol
R
th(j-c)_IGBT
R
th(j-c)_FWD
Limit
Min
-
-
Typ
-
-
Max
3.0
3.9
Unit
°C /W
°C /W
Conditions
Inverter IGBT(1/6 module)
Inverter FWD(1/6 module)
(Note 2) Grease with good conductivity and high reliability should be applied evenly with +100 to +200µm on the contacting surface of IPM and heat sink. Use
a torque wrench to fasten up to the specified torque rating. The contacting thermal resistance between IPM case and heat sink is determined by the
thickness and the thermal conductivity of the applied grease.
Caution:
Operating the IPM over the absolute maximum ratings may damage the IPM. The damage can either be a short circuit between pins or an open
circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IPM is
1. Introduction
GD also produces memory. Currently, the company uses GD25Q256E memory. This memory is relatively small and very suitable for our current products. It adopts QSPI communication mode. To...
[color=#222222][backcolor=rgb(238, 238, 238)][font=sans-serif]A one-wheeled motorcycle invented by Italian M. Goventosa de Udine, with a maximum speed of 150 kilometers per hour (93 miles per hour), 1...
I read Huawei's data, which says that the selection of the two capacitor values before and after the Pi-type filter is as follows: the DC capacitor is 10UF, and the AC capacitor is 0.01 to 1UF. I don'...
If the ultimate form of a car is a silicon-based life form, then in
the field of
intelligent driving
, it has gradually taken on the appearance of a "veteran driver." In
the field of
the ...[Details]
introduction
Bluetooth technology is a short-range wireless communication technology designed to replace wired cables. It is a wireless communication technology standard developed by the SIG, ...[Details]
Is electromagnetic radiation from electric vehicles harmful to the human body? Recently, the issue of electromagnetic radiation from electric vehicles has garnered widespread attention. However, pu...[Details]
New energy pure electric vehicles generally accelerate faster than comparable fuel-powered vehicles, both from a standing start and while accelerating. Many believe this is simply due to the motor'...[Details]
1. Introduction
Electronic scales are gradually replacing traditional measuring tools like springs and balances in everyday life, such as electronic price computing scales and electronic weigh...[Details]
Amidst the wave of intelligent automotive transformation, advanced driver assistance is gradually emerging from cutting-edge technology into the mainstream, becoming a new frontier of industry comp...[Details]
With the rapid adoption of smart electric vehicles, automotive chips are evolving from auxiliary control units to the foundation of the entire vehicle's intelligence. Their applications extend from...[Details]
Charging is a familiar process for new energy vehicles, and as a source of battery energy, charging piles are crucial. New energy vehicle charging can be divided into fast charging and slow chargin...[Details]
According to Nikkei, Japan has performed poorly in responding to China's power semiconductor challenges.
There are five major companies in Japan's power chip market: Mitsubishi Electric,...[Details]
During daily operation of an R-type power transformer, the voltage used varies as the equipment being used adjusts. This raises the question: can the transformer change voltage at this point? The a...[Details]
Over the past decade, the narrative surrounding fuel vehicles has been one of decline and replacement. Under the onslaught of new energy vehicles, traditional automakers have been forced to acceler...[Details]
Tools/Materials
Yitong Chuanglian MODBUS to PROFIBUS Gateway YT-PB-03
Siemens s7-300
This article describes how to configure the YT-PB-03 MODBUS to PROFIBUS gat...[Details]
For self-driving cars, LiDAR is the sensory organ that allows them to "see the road." Simply put, its operating principle involves sending out a laser beam, receiving the echo, and ultimately gener...[Details]
The Waveshare ESP32-P4-ETH is a compact ESP32-P4 development board with Ethernet and PoE support. It looks very similar to the Olimex ESP32-P4-DevKit, minus the pUEXT connector. However, we've also...[Details]
The drive shaft is the shaft in a universal joint that transmits power. As a high-speed, low-support rotating body, its dynamic balance is crucial. Generally, drive shafts undergo dynamic balancing...[Details]