performance oscillators utilize a proven silicon MEMS
technology to provide excellent jitter and stability over
a wide range of supply voltages and temperatures. By
eliminating the need for quartz or SAW technology,
MEMS oscillators significantly enhance reliability and
accelerate product development, while meeting
stringent clock performance criteria for a variety of
communications, storage, and networking applications.
DSC1101 has a standby feature that allows it to
completely power-down when EN pin is pulled low;
whereas for DSC1121, only the outputs are disabled
when EN is low. Both oscillators are available in
industry standard packages, including the small
2.5 mm x 2.0 mm, and are “drop-in” replacements for
standard 4-pin CMOS quartz crystal oscillators.
Functional Block Diagram
Applications
• Storage Area Networks
- SATA, SAS, Fibre Channel
• Passive Optical Networks
- EPON, 10G-EPON,V GPON, 10G-PON
• Ethernet
- 1G, 10GBASE-T/KR/LR/SR, and FCoE
• HD/SD/SDI Video and Surveillance
• PCI Express
• Display Port
2017 Microchip Technology Inc.
DS20005613B-page 1
DSC1101/21
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
Input Voltage, V
IN
..............................................................................................................................–0.3V to V
DD
+ 0.3V
Supply Voltage .......................................................................................................................................... –0.3V to +4.0V
ESD Protection On All Pins ........................................................................................... 4000V HBM, 1500V CDM (max.)
† Notice:
Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Note:
1000+ years of data retention on internal memory.
TABLE 1-1:
DC CHARACTERISTICS
Electrical Characteristics
Parameters
Supply Voltage (Note
1)
Sym.
V
DD
Min.
2.25
—
Supply Current
I
DD
—
—
Frequency Stability
(Including frequency
variations due to initial
tolerance, temp. and
power supply voltage.)
Aging
Startup Time (Note
2)
Input Logic Levels
Input Logic High
Input Logic Low
Output Disable Time
(Note
3)
Output Enable Time
Enable Pull-up Resistor
(Note
4)
CMOS Output
Output Logic Levels
Output Logic High
Output Logic Low
Note 1:
2:
3:
4:
V
OH
V
OL
0.9
V
DD
—
—
—
—
0.1
V
DD
V
I = ±6 mA
—
Typ.
—
—
20
31
—
—
—
—
—
—
—
—
—
—
40
Max.
3.6
0.095
22
35
±10
±20
—
—
—
—
0.75
V
DD
—
—
—
—
—
±25
±50
±5
5
—
0.1
V
DD
5
5
20
—
V
ns
ms
ns
k
—
—
DSC1101
DSC1121
Pull-up Resistor Exist
ppm
ms
ppm
mA
Units
V
—
DSC1101, EN pin low, output
is disabled
DSC1121, EN pin low, output
is disabled
Output enabled, C
L
= 15 pF,
F
0
= 100 MHz
Ext Comm. & Ind. only
All temp ranges
All temp ranges
All temp ranges
1 year @ 25°C
T = 25°C
Conditions
f
f
t
SU
V
IH
V
IL
t
DS
t
EN
—
Pin 6 V
DD
should be filtered with 0.1 µF capacitor.
t
SU
is time to 100 ppm of output frequency after V
DD
is applied and outputs are enabled.
Output Waveform and Test Circuit figures define the parameters.
Output is enabled if pad is floated or not connected.
DS20005613B-page 2
2017 Microchip Technology Inc.
DSC1101/21
TABLE 1-1:
DC CHARACTERISTICS (CONTINUED)
Electrical Characteristics
Parameters
Output Transition Time
Rise Time
Fall Time
Sym.
t
R
t
F
Min.
—
—
2.3
Frequency
f
0
3.3
Output Duty Cycle
Period Jitter
Integrated Phase Noise
SYM
J
PER
J
PH
45
—
—
—
—
Note 1:
2:
3:
4:
—
—
3
0.3
0.38
1.7
170
55
—
—
—
2
ps
RMS
%
ps
RMS
Typ.
1.1
1.3
—
Max.
2
2
170
MHz
ns
Units
Conditions
20% to 80%
C
L
= 15 pF
C
L
= 15 pF, –20°C to +70°C
and –40°C to +85°C
C
L
= 15 pF, –40°C to +105°C
and –55°C to +125°C
—
F
OUT
= 125 MHz
200 kHz to 20 MHz @ 125 MHz
100 kHz to 20 MHz @ 125 MHz
12 kHz to 20 MHz @ 125 MHz
Pin 6 V
DD
should be filtered with 0.1 µF capacitor.
t
SU
is time to 100 ppm of output frequency after V
DD
is applied and outputs are enabled.
Output Waveform and Test Circuit figures define the parameters.
Output is enabled if pad is floated or not connected.
2017 Microchip Technology Inc.
DS20005613B-page 3
DSC1101/21
TEMPERATURE SPECIFICATIONS (Note
1)
Parameters
Temperature Ranges
T
A
Operating Temperature Range (T)
T
A
T
A
T
A
Junction Operating Temperature
Storage Temperature Range
Soldering Temperature Range
Note 1:
T
J
T
A
T
S
–20
–40
–40
–55
—
–40
—
—
—
—
—
—
—
—
+70
+85
+105
+125
+150
+150
+260
°C
°C
°C
°C
°C
°C
°C
Ordering Option E
Ordering Option I
Ordering Option L
Ordering Option M
—
—
40 sec. max
Sym.
Min.
Typ.
Max.
Units
Conditions
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
junction temperature and the thermal resistance from junction to air (i.e., T
A
, T
J
,
JA
). Exceeding the
maximum allowable power dissipation will cause the device operating junction temperature to exceed the
maximum +125°C rating. Sustained junction temperatures above +125°C can impact the device reliability.
DS20005613B-page 4
2017 Microchip Technology Inc.
DSC1101/21
2.0
Note:
NOMINAL PERFORMANCE CURVES
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:59[/i] Mobile phones have become a major communication tool in our lives, but they are very common with a security problem. Phone theft...
Why can't the butterfly unit in dsp buider output negative numbers? For example, if the input is 1 and 10, the W factor is 1 and the output should be 11 and -9, but the result after I run it is 11 and...
1. Important protection units1. CPU2. CPU interrupt (VIM)3. System control unit: power supply, reset, clock4. Key parts of the operating system: DMA, [/color]OS[/font]Timer[/color][/align][align=left]...
I am still a student, majoring in Internet of Things. I just want to ask you seniors, what would you be like if you were still a student? How would you change yourself? Now I am also very confused. I ...
How do you know if a machine is operating properly? The answer: by leveraging deep learning to detect anomalies in routine vibration data from industrial machines. Anomaly detection has many uses, ...[Details]
Reflow soldering, a common soldering method in modern electronics manufacturing, primarily melts solder paste and pads to form solder joints. With technological advancements, soldering equipment ha...[Details]
In mobile technology, sensors are the primary input for measured signals and form a component of a sensor system. They include sensitive and transducer elements connected to carriers and circuits. ...[Details]
White light LEDs are voltage-sensitive devices. In actual operation, their upper limit is 20mA. However, the current often increases due to various reasons during use. If no protective measures are...[Details]
Based on a survey of more than ten intelligent robot companies, this article sorts out and analyzes the current development status of the intelligent industry and the challenges and differences it ...[Details]
The Automotive Testing and Quality Assurance Expo (ATE 2025) will open on August 27th. At the expo, Rohde & Schwarz (R&S) will showcase six automotive testing solutions, themed "Intelligently Drivi...[Details]
Overview
As handheld voice communication devices become more and more popular, they are increasingly used in noisy environments, such as airports, busy roads, crowded bars, etc. In such noisy ...[Details]
Electric vehicles are becoming increasingly popular, with increasingly longer ranges. There are two ways to charge electric vehicles: slow charging and fast charging. Which is the most suitable? Sl...[Details]
Linear motor modules have become the "sweet spot" in various fields due to their advantages such as long stroke, fast speed, high precision, smooth operation and long life. Different models of line...[Details]
Intel®
Xeon®
6
-
core processors now support the new Amazon EC2 R8i and R8i-flex instances on Amazon Web Services (AWS).
These new instances offer superior performance and fast...[Details]
The range of an electric vehicle is crucial to the driving experience, and range anxiety is a common headache when driving an electric vehicle. Although the latest electric vehicles can achieve a r...[Details]
On August 21, according to a report by Korean media SEDaily yesterday, according to semiconductor industry sources, the HBM4 samples provided by Samsung to Nvidia last month have passed initial tes...[Details]
Consumer demand for premium listening experiences has driven rapid evolution in the wireless headphone market in recent years. Hybrid designs, which utilize two drivers per earbud to enhance sound ...[Details]
Summer is the peak season for buying and using air conditioners. Do you pay attention to the energy efficiency of your air conditioner? Did you buy a DC inverter air conditioner? Do you know the re...[Details]
The mobile computing market is rapidly evolving, and manufacturers are fiercely competing for market share. A key area of competition is battery life, which encompasses two key aspects: how long th...[Details]
Mobile and portable
京公网安备 11010802033920号
EEWORLD
