EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4QV01KG-2163CDI8

Description
Programmable Oscillators PROGRAMMABLE 5X7 OSCILLATOR
CategoryPassive components   
File Size329KB,20 Pages
ManufacturerIDT (Integrated Device Technology)
Download Datasheet Parametric View All

8N4QV01KG-2163CDI8 Online Shopping

Suppliers Part Number Price MOQ In stock  
8N4QV01KG-2163CDI8 - - View Buy Now

8N4QV01KG-2163CDI8 Overview

Programmable Oscillators PROGRAMMABLE 5X7 OSCILLATOR

8N4QV01KG-2163CDI8 Parametric

Parameter NameAttribute value
Product AttributeAttribute Value
ManufacturerIDT (Integrated Device Technology)
Product CategoryProgrammable Oscillators
RoHSN
ProductVCXO
Package / Case7 mm x 5 mm
Length7 mm
Width5 mm
Height1.55 mm
PackagingCut Tape
PackagingReel
Factory Pack Quantity1000
Unit Weight0.006562 oz
Quad-Frequency Programmable
VCXO
General Description
The IDT8N4QV01 is a Quad-Frequency Programmable VCXO with
very flexible frequency and pull-range programming capabilities. The
device uses IDT’s fourth generation FemtoClock® NG technology for
an optimum of high clock frequency and low phase noise
performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 10-lead ceramic 5mm x
7mm x 1.55mm package.
Besides the 4 default power-up frequencies set by the FSEL0 and
FSEL1 pins, the IDT8N4QV01 can be programmed via the I
2
C
interface to any output clock frequency between 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz to a very high degree of
precision with a frequency step size of 435.9Hz ÷N (N is the PLL
output divider). Since the FSEL0 and FSEL1 pins are mapped to 4
independent PLL, P, M and N divider registers (P, MINT, MFRAC and
N), reprogramming those registers to other frequencies under
control of FSEL0 and FSEL1 is supported. The extended
temperature range supports wireless infrastructure, tele-
communication and networking end equipment requirements.
IDT8N4QV01 REV G
DATASHEET
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Four power-up default frequencies (see part number order codes),
re-programmable by I
2
C
I
2
C programming interface for the output clock frequency, APR
and internal PLL control registers
Frequency programming resolution is 435.9Hz ÷N
Absolute pull-range (APR) programmable from ±4.5ppm to
±754.5ppm
One 2.5V or 3.3V LVDS differential clock output
Two control inputs for the power-up default frequency
LVCMOS/LVTTL compatible control inputs
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.494ps
(typical)
RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.594ps (typical)
2.5V or 3.3V supply voltage modes
-40°C to 85°C ambient operating temperature
Lead-free (RoHS 6) packaging
Block Diagram
OSC
114.285 MHz
÷MINT,
MFRAC
2
VC
FSEL1
FSEL0
SCLK
SDATA
OE
Pulldown
Pulldown
Pullup
Pullup
Pullup
Pin Assignment
÷P
PFD
&
LPF
FemtoClock
®
NG
VCO
1950-2600MHz
÷N
Q
nQ
VC 1
OE 2
GND 3
FSEL0 4
FSEL1 5
10 SCLK
9 SDATA
8 V
DD
7 nQ
6 Q
A/D
7
25
Configuration Register (ROM)
(Frequency, APR, Polarity)
I
2
C Control
7
IDT8N4QV01 REV G DATA SHEET
10-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4QV01GCD REVISION A MARCH 11, 2014
1
©2014 Integrated Device Technology, Inc.
2013 Electrical Design, what type of multipliers do you prepare?
[i=s] This post was last edited by paulhyde on 2014-9-15 03:22 [/i] Now it’s time for all kinds of preparations and discussions. What kind of multipliers did everyone buy?...
丨小李 Electronics Design Contest
Mobile phone test data release
...
bolibo123 Test/Measurement
Why is InitializeHandler not called automatically by the NDIS driver?
A network card driver, using NDIS5.1, added CDEFINES=$(CDEFINES) -DNDIS_MINIPORT_DRIVER=1 -DNDIS51_MINIPORT=1 in sources, initialized in DriverEntry: NDIS_MINIPORT_CHARACTERISTICS ch; ... ch.MajorNdis...
saqi99 Embedded System
[ESP32-Korvo Review] 08 ESP-Skainet Development Preparation
[i=s]This post was last edited by Tianyiwuzui on 2021-3-20 20:30[/i]After a few nights of hard work, I finally set up the ESP-IDF development environment. Now it’s time to get down to business: voice ...
天意无罪 Domestic Chip Exchange
[Ask] How to handle multiple interrupts in Keil more reasonably and avoid exceptions?
For example: I use a circular queue to store and send messages. The queue uses an array of fixed length, where the length of the array must be longer than each message. There are 8 arrays in the queue...
digi01 Embedded System
Digital tube size list
Digital tube size list, collected from the Internet...
刘小飞 Discrete Device

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 652  211  2919  2887  824  14  5  59  17  11 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号