The MAX6477–MAX6484 are constructed using a unique set of packaging techniques that impose a limit on the thermal pro-
file the devices can be exposed to during board-level solder attach and rework. This limit permits only the use of the solder
profiles recommended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and
Convection reflow. Pre-heating is required. Hand or wave soldering is not allowed.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
IN
= (V
OUT
+ 0.5V) or +2.5V, whichever is greater, C
OUT
= 3.3µF, T
A
= -40°C to +85°C. Typical specifications are at T
A
= +25°C,
unless otherwise noted.) (Note 2)
PARAMETER
Input Voltage Range
Input Undervoltage Lockout
Supply Current (Ground Current)
Shutdown Supply Current
REGULATOR CIRCUIT
Output Current
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6469–MAX6476
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6477–MAX6484
Adjustable Output Voltage Range
SET Reference Voltage
SET Dual Mode
TM
Threshold
SET Input Leakage Current
1mA
≤
I
OUT
≤
150mA, T
A
= +25°C
1mA
≤
I
OUT
≤
150mA, T
A
= -40°C to +85°C
1mA
≤
I
OUT
≤
300mA, T
A
= -40°C to +85°C
2mA
≤
I
OUT
≤
100mA, T
A
= +25°C
2mA
≤
I
OUT
≤
100mA, T
A
= -40°C to +85°C
2mA
≤
I
OUT
≤
300mA, T
A
= -40°C to +85°C
(Note 3)
V
SET
I
SET
V
SET
= 0V, +1.2V (Note 3)
SYMBOL
V
IN
V
UVLO
I
Q
I
SHDN
V
IN
falling
I
OUT
= 0A
I
OUT
= 300mA
T
A
= +25°C
300
-1.3
-2.3
-2.7
-1.1
-2.0
-2.5
V
SET
1.200
CONDITIONS
MIN
2.5
2.25
82
96
0.1
TYP
MAX
5.5
2.47
136
1
UNITS
V
V
µA
µA
mA
+1.3
+2.3
+2.7
+1.1
+2.0
+2.5
5.0
1.258
±100
V
V
mV
nA
%
%
1.229
185
±20
Dual Mode is a trademark of Maxim Integrated Products, Inc.
[b][font=Verdana][size=10.5pt][/size][/font][/b] [font=宋体][size=10pt]Charging solution for lithium iron phosphate mining lamp[/size][/font][font=Verdana][size=10pt]—CN3058/CN3059--[/size][/font][font=...
Dear experts: I am currently studying a project about using isp1161 as a usbhost, with a USB flash drive as the device end. It requires a large delay to achieve batch transmission, usually tens or eve...
Use one microcontroller as the master and the others as slaves. The master and slaves can communicate with each other. Can the serial port of the 51 microcontroller do full-duplex communication?...
DSP systems generally have two voltages: core power supply (low, mostly 1.2, 1.6, 1.8V) and I/O (high, mostly 5 3.3, 2.5V), and the two power supplies are separate. Power supply order: The core voltag...
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
The Mobile Industry Processor Interface (MIPI) Alliance is an organization responsible for promoting the standardization of software and hardware in mobile devices. It has released the D-PHY specif...[Details]
1 Introduction
Ultrasonic waves have strong directivity, slow energy consumption, and can propagate over long distances in a medium, so they are used for distance measurement. Ultrasonic detec...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
The invention of the steam engine ushered in the first conversion of internal energy and mechanical energy for mankind, and the birth of the internal combustion engine at the end of the 19th centur...[Details]
LED is the abbreviation of the English word. Its main meanings are: LED = Light Emitting Diode, a solid-state semiconductor device that can convert electrical energy into visible light. It can dire...[Details]
a. Keep the battery clean, wipe off the spilled electrolyte, contaminated dirt and dust in time; keep the poles and terminal clamps clean and in good contact, and apply vaseline or butter to preven...[Details]
HL201A is a special thick film driver integrated circuit with a capacity of less than 75AGTR developed by Xi'an Power Electronics Technology Research Institute. The article explains the pin arrange...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
