SCOPE: IMPROVED, QUAD, SPST, CMOS ANALOG MULTIPLEXER
Device Type
01
02
Generic Number
DG441A(x)/883B
DG442A(x)/883B
Case Outline(s).
The case outlines shall be designated in Mil-Std-1835 and as follows:
Outline Letter
K
Z
Mil-Std-1835
GDIP1-T16 or CDIP2-T16
CQCC1-N20
Case Outline
Package Code
16 LEAD CERDIP
J16
20-Pin Ceramic LCC
L20
Absolute Maximum Ratings
Voltage Referenced to V
-
V
+
to V
-
.............................................................................................................................. 44V
V
-
to GND .......................................................................................................................... 25V
V
L
................................................................................................... (GND-0.3V) to V+ +0.3V)
Digital Inputs, V
S
, V
D
1/ ..........................................................................(V
-
) -2V to (V
+
)+2V
or 30mA whichever occurs first
Continuous Current, Any terminal .................................................................................. 30mA
Peak Current, S or D (Pulsed at 1ms, 10% duty cycle max) ......................................... 100mA
Lead Temperature (soldering, 10 seconds) ........................................................................ +300°C
Storage Temperature ........................................................................................... -65°C to +150°C
Continuous Power Dissipation ........................................................................…….... T
A
=+70°C
16 lead CERDIP(derate 10.0mW/°C above +70°C) ...............................................…….. 800mW
20 lead LCC (derate 9.1mW/°C above +70°C) ......................................................…….. 727mW
Junction Temperature T
J
....................................................................................………. +150°C
Thermal Resistance, Junction to Case,
ΘJC:
Case Outline 16 lead CERDIP...............................................................…….... 50°C/W
Case Outline 20 lead LCC .....................................................................……... 20°C/W
Thermal Resistance, Junction to Ambient,
ΘJA:
Case Outline 16 lead CERDIP.............................................................…….... 100°C/W
Case Outline 20 lead LCC ...................................................................……... 110°C/W
Recommended Operating Conditions
Ambient Operating Range (T
A
) .........................................................……….. -55°C to
+125°C
Positive Supply Voltage (V
+
) ...............................................................................………... +15V
Negative Supply Voltage (V
-
) ..............................................................................……….... -15V
V
AL
(max) .............................................................................................................…….…... 0.8V
V
AH
(min) .............................................................................................................……….... 2.4V
NOTE 1: Signals on S, D, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward current
to maximum current ratings.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
----------------------------
Electrical Characteristics of DG441A/DG442A/883B
19-0093
Page 2 of
Rev. C
6
TABLE 1. ELECTRICAL TESTS:
SINGLE SUPPLY
Group A
Subgroup
Device
type
TEST
Symbol
CONDITIONS
-55
°C
<=T
A
<= +125°C
V
+
=+12V, V
-
=0V, GND=0V
V
AH
=2.4V, V
AL
=0.8V
Unless otherwise specified
NOTE 3
I
S
=1.0mA, V
D
=3V or 8V,
V
+
=10.8V
Limits
Min
2/
Limits
Max
2/
Units
SWITCH
Analog-Signal
Range
Drain-Source ON
Resistance
SUPPLY
Power Supply
Range
Positive Supply
Current
Negative Supply
Current
Ground Current
DYNAMIC
Turn-On Time
Turn-Off Time
Charge Injection
V
ANALOG
1,2,3
All
All
0
12
160
200
V
Ω
r
DS(ON)
1,3
2
1,2,3
All
All
All
All
All
All
All
10
30
100
V
µA
µA
µA
I+
I-
IGND
All channels on or off,
V
IN
=0 or 5V
All channels on or off,
V
IN
=0 or 5V
All channels on or off, V
IN
=0 or 5V
V
S
=8V, Figure 2
V
S
=8V, Figure 2
C
L
=1nF, V
GEN
=0V
1,2,3
1
2,3
1,2,3
9
9
9
-1
-5
-100
1
5
t
ON
t
OFF
Q
NOTE 3
400
200
10
ns
ns
pC
NOTE 2: The algebraic convention, where the most negative value is a minimum and the most positive value a
maximum, is used in this data sheet.
NOTE 3: Guaranteed by design.
NOTE 4: On-resistance match between channels and flatness is guaranteed only with bipolar-supply operation.
Flatness is defined as the difference between the maximum and the minimum value of on-resistance
as measured at the extremes of the specified analog range.
TRUTH TABLE
TERMINAL CONNECTION
DG441A
TERMINAL
01
01
02
02
LOGIC
SWITCH
NUMBER
DG441A
DG441A
DG442A
DG442A
0
ON
J16
20LCC
J16
20LCC
1
OFF
1
IN1
NC
IN1
NC
2
D1
IN1
D1
IN1
3
S1
D1
S1
D1
4
V-
S1
V-
S1
LOGIC
DG442A
5
GND
V-
GND
V-
SWITCH
0
OFF
6
S4
NC
S4
NC
1
ON
7
D4
GND
D4
GND
8
IN4
S4
IN4
S4
9
IN3
D4
IN3
D4
10
D3
IN4
D3
IN4
11
S3
NC
S3
NC
12
NC
IN3
NC
IN3
13
V+
D3
V+
D3
14
S2
S3
S2
S3
15
D2
NC
D2
NC
16
IN2
NC
IN2
NC
17
V+
V+
18
S2
S2
19
D2
D2
20
IN2
IN2
----------------------------
Electrical Characteristics of DG441A/DG442A/883B
19-0093
Page 4 of
Rev. C
6
Figure 2.
Switching Time: See Commercial Data Sheet.
Figure 3.
Charge Injection: See Commercial Data Sheet.
ORDERING INFORMATION:
DG441AK/883B
16 CDIP
DG441AZ/883B
20 LCC
DG442AK/883B
DG442AZ/883B
16 CDIP
20 LCC
QUALITY ASSURANCE
Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil-
Std-883.
Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:
1. Test Condition, A, B, C, or D.
2. TA = +125°C minimum.
3. Interim and final electrical test requirements shall be specified in Table 2.
Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B,
C, and D inspection.
Group A inspection:
1. Tests as specified in Table 2.
2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.
Group C and D inspections:
a. End-point electrical parameters shall be specified in Table 1.
b. Steady-state life test, Method 1005 of Mil-Std-883:
1. Test condition A, B, C, D.
2. TA = +125°C, minimum.
3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.
TABLE 2.
ELECTRICAL TEST REQUIREMENTS
Mil-Std-883 Test Requirements
Subgroups
per Method 5005, Table 1
1
1*, 2, 3, 9
1, 2, 3, 9
1
Interim Electric Parameters
Method 5004
Final Electrical Parameters
Method 5005
Group A Test Requirements
Method 5005
Group C and D End-Point Electrical Parameters
Method 5005
*
PDA applies to Subgroup 1 only.
----------------------------
Electrical Characteristics of DG441A/DG442A/883B
19-0093
Page 5 of
Rev. C
6
京公网安备 11010802033920号
EEWORLD
