The MAX17048/MAX17049 ICs are tiny, micropower cur-
rent fuel gauges for lithium-ion (Li+) batteries in handheld
and portable equipment. The MAX17048 operates with
a single lithium cell and the MAX17049 with two lithium
cells in series.
The ICs use the sophisticated Li+ battery-modeling algo-
rithm ModelGauge™ to track the battery relative state-of-
charge (SOC) continuously over widely varying charge
and discharge conditions. The ModelGauge algorithm
eliminates current-sense resistor and battery-learn cycles
required in traditional fuel gauges. Temperature compen-
sation is implemented using the system microcontroller.
The ICs automatically detect when the battery enters a
low-current state and enters low-power 3µA hibernate
mode, while still providing accurate fuel gauging. The
ICs automatically exit hibernate mode when the system
returns to active state.
On battery insertion, the ICs debounce initial voltage
measurements to improve the initial SOC estimate,
thus allowing them to be located on system side. SOC,
voltage, and rate information is accessed using the I
2
C
interface. The ICs are available in a tiny 0.9mm x 1.7mm,
8-bump wafer-level package (WLP), or a 2mm x 2mm,
8-pin TDFN package.
●
MAX17048: 1 Cell, MAX17049: 2 Cells
●
Precision ±7.5mV/Cell Voltage Measurement
●
ModelGauge Algorithm
• Provides Accurate State-of-Charge
• Compensates for Temperature/Load Variation
• Does Not Accumulate Errors, Unlike Coulomb
Counters
• Eliminates Learning
• Eliminates Current-Sense Resistor
●
Ultra-Low Quiescent Current
•
3μA Hibernate, 23μA Active
• Fuel Gauges in Hibernate Mode
• Automatically Enters and Exits Hibernate Mode
●
Reports Charge and Discharge Rate
●
Battery-Insertion Debounce
• Best of 16 Samples to Estimate Initial SOC
●
Programmable Reset for Battery Swap
• 2.28V to 3.48V Range
●
Configurable Alert Indicator
• Low SOC
• 1% Change in SOC
• Battery Undervoltage/Overvoltage
• VRESET Alert
●
I
2
C Interface
●
8-Bit OTP ID Register (Contact Factory)
Features and Benefits
Applications
●
●
●
●
●
●
●
●
●
Smartphones, Tablets
Smartwatches, Wearables
Bluetooth Headsets
Health and Fitness Monitors
Digital Still, Video, and Action Cameras
Medical Devices
Handheld Computers and Terminals
Wireless Speakers
Home and Building Automation, Sensors
Simple Fuel-Gauge Circuit Diagram
MAX17048
V
DD
ONLY ONE
EXTERNAL
COMPONENT
CELL
CTG
GND
ALRT
SDA
SCL
QSTRT
SYSTEM
µP
Ordering Information
appears at end of data sheet.
ModelGauge is a trademark of Maxim Integrated Products, Inc.
19-6171; Rev 7; 11/16
MAX17048/MAX17049
3μA 1-Cell/2-Cell Fuel Gauge with ModelGauge
Absolute Maximum Ratings
CELL to GND ........................................................-0.3V to +12V
All Other Pins to GND .............................................-0.3V to +6V
Continuous Sink Current, SDA,
ALRT
...............................20mA
Operating Temperature Range ........................... -40°C to +85°C
Storage Temperature Range ............................ -55°C to +125°C
Lead Temperature (TDFN only) (soldering, 10s) ............+300°C
Soldering Temperature (reflow).......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(V
DD
= 2.5V to 4.5V, T
A
= -20°C to +70°C, unless otherwise noted. Typical values are at T
A
= +25°C.) (Note 1)
PARAMETER
Supply Voltage
Fuel-Gauge SOC Reset
(VRESET Register)
Data I/O Pins
SYMBOL
V
DD
V
RST
SCL, SDA,
ALRT
(Note 2)
Configuration range, in 40mV steps
Trimmed at 3V
(Note 2)
Sleep mode, T
A
≤ +50°C
Supply Current
I
DD0
Hibernate mode, reset comparator
disabled (VRESET.Dis = 1)
Hibernate mode, reset comparator
enabled (VRESET.Dis = 0)
I
DD1
Time Base Accuracy
ADC Sample Period
Voltage Error
Voltage-Measurement Resolution
Voltage-Measurement Range
SDA, SCL, QSTRT Input
Logic-High
SDA, SCL, QSTRT Input
Logic-Low
SDA,
ALRT
Output
Logic-Low
SDA, SCL Bus
Low-Detection Current
Bus Low-Detection Timeout
V
IH
V
IL
V
OL
I
PD
t
SLEEP
I
OL
= 4mA
V
SDA
= V
SCL
= 0.4V (Note 5)
(Note 6)
1.75
0.2
MAX17048: V
DD
pin
MAX17049: CELL pin
2.5
5
1.4
0.5
0.4
0.4
2.5
V
ERR
t
ERR
Active mode
Active, hibernate modes (Note 3)
Active mode
Hibernate mode
V
CELL
= 3.6V, T
A
= +25°C (Note 4)
-7.5
-20
1.25
5
10
-3.5
CONDITIONS
MIN
2.5
2.28
2.85
-0.3
0.5
3
4
23
±1
250
45
+7.5
+20
40
+3.5
%
ms
s
mV/cell
mV/cell
V
V
V
V
µA
s
3.0
TYP
MAX
4.5
3.48
3.15
+5.5
2
5
µA
UNITS
V
V
V
V
www.maximintegrated.com
Maxim Integrated
│
2
MAX17048/MAX17049
3μA 1-Cell/2-Cell Fuel Gauge with ModelGauge
Electrical Characteristics (I
2
C INTERFACE)
(2.5V < V
DD
< 4.5V, T
A
= -20°C to +70°C, unless otherwise noted.) (Note 1)
PARAMETER
SCL Clock Frequency
Bus Free Time Between a
STOP and START Condition
START Condition (Repeated)
Hold Time
Low Period of SCL Clock
High Period of SCL Clock
Setup Time for a Repeated
START Condition
Data Hold Time
Data Setup Time
Rise Time of Both SDA and
SCL Signals
Fall Time of Both SDA and SCL
Signals
Setup Time for STOP Condition
Spike Pulse Widths Suppressed
by Input Filter
Capacitive Load for Each Bus
Line
SCL, SDA Input Capacitance
SYMBOL
f
SCL
t
BUF
t
HD:STA
t
LOW
t
HIGH
t
SU:STA
t
HD:DAT
t
SU:DAT
t
R
t
F
t
SU:STO
t
SP
C
B
C
B,IN
(Note 11)
(Note 12)
(Notes 9, 10)
(Note 9)
(Note 8)
(Note 7)
CONDITIONS
MIN
0
1.3
0.6
1.3
0.6
0.6
0
100
20 + 0.1CB
20 + 0.1CB
0.6
0
50
400
60
300
300
0.9
TYP
MAX
400
UNITS
kHz
µs
µs
µs
µs
µs
µs
ns
ns
ns
µs
ns
pF
pF
Note 1:
Specifications are 100% tested at T
A
= +25°C. Limits over the operating range are guaranteed by design and
characterization.
Note 2:
All voltages are referenced to GND.
Note 3:
Test is performed on unmounted/unsoldered parts.
Note 4:
The voltage is trimmed and verified with 16x averaging.
Note 5:
This current is always present.
Note 6:
The IC enters shutdown mode after SCL < V
IL
and SDA < V
IL
for longer than 2.5s.
Note 7:
Timing must be fast enough to prevent the IC from entering sleep mode due to bus low for period > t
SLEEP
.
Note 8:
f
SCL
must meet the minimum clock low time plus the rise/fall times.
Note 9:
The maximum t
HD:DAT
has to be met only if the device does not stretch the low period (t
LOW
) of the SCL signal.
Note 10:
This device internally provides a hold time of at least 100ns for the SDA signal (referred to the V
IH,MIN
of the SCL signal) to
bridge the undefined region of the falling edge of SCL.
Note 11:
Filters on SDA and SCL suppress noise spikes at the input buffers and delay the sampling instance.
Note 12:
C
B
is total capacitance of one bus line in pF.
www.maximintegrated.com
Maxim Integrated
│
3
MAX17048/MAX17049
3μA 1-Cell/2-Cell Fuel Gauge with ModelGauge
SDA
t
F
t
LOW
t
R
t
SU:DAT
t
F
t
HD:STA
t
SP
t
R
t
BUF
SCL
t
HD:STA
t
SU:STA
t
SU:STO
S
t
HD:DAT
Sr
P
S
Figure 1. I
2
C Bus Timing Diagram
Typical Operating Characteristics
QUIESCENT CURRENT vs. SUPPLY
VOLTAGE (HIBERNATE MODE)
MAX17048 toc01
(T
A
= +25°C, battery is Sanyo UF504553F, unless otherwise noted.)
QUIESCENT CURRENT vs. SUPPLY
VOLTAGE (ACTIVE MODE)
MAX17048 toc02
QUIESCENT CURRENT (µA)
QUIESCENT CURRENT (µA)
4
3
VOLTAGE ADC ERROR (mV/CELL)
T
A
= +70°C
35
30
25
20
15
10
5
T
A
= +25°C
T
A
= -20°C
T
A
= +70°C
15
10
5
0
-5
-10
-15
-20
-20
-5
10
25
40
55
V
CELL
= 2.5V
V
CELL
= 3.6V
V
CELL
= 4.5V
T
A
= -20°C
2
1
0
T
A
= +25°C
2.5
3.0
3.5
V
CELL
(V)
4.0
4.5
0
2.5
3.0
3.5
V
CELL
(V)
4.0
4.5
70
TEMPERATURE (°C)
0.50
C
RATE
(%/Hr)
0.25
0
CURRENT (I_BATT mA, I_DD uA)
0.75
MAX17048 C
RATE
MAX17048 toc04
1.00
C
RATE
ACCURACY
600
500
400
300
200
100
0
-100
ENTER HIBERNATE MODE
AUTOMATICALLY
MAX17048 toc05
4.00
3.95
V
BATT
3.90
3.85
V
BATT
(V)
-0.25
-0.50
-0.75
-1.00
-4
I
BATT
3.80
3.75
3.70
MEASURED C
RATE
-2
0
2
TIME (Hr)
4
6
8
I
DD1
0
5
10
TIME (min)
I
DD0
15
20
3.65
www.maximintegrated.com
Maxim Integrated
│
4
MAX17048 toc03
5
40
20
VOLTAGE ADC ERROR vs. TEMPERATURE
MAX17048/MAX17049
3μA 1-Cell/2-Cell Fuel Gauge with ModelGauge
Typical Operating Characteristics (continued)
(T
A
= +25°C, battery is Sanyo UF504553F, unless otherwise noted.)
Error: Module TouchKit.dll built for ARM, kernel built for I386 Fatal error hit, exiting... makeimg: FATAL ERROR: Command returned non-zero exit code 1 (dec). makeimg: FATAL ERROR: Command returned no...
I want to take the postgraduate entrance exam and go to a prestigious university because my undergraduate school is so lousy; I am fascinated by microcontrollers, and I want to join this industry; I a...
Volkswagen self-driving baby prototype : https://training.eeworld.com.cn/course/2278[size=4][b]Volkswagen recently released a unique prototype car. A video released shows a dad taking a stroll with a ...
[size=3]Series switching power supply output voltage filter circuit[color=#008000]1-2-2. Series switching power supply output voltage filter circuit[/color] Most switching power supplies output DC vol...
My STM32 is modified using ST's official Mass_Storage. Endpoint 1 is IN and Endpoint 2 is OUT. Both endpoints are bulk transfer endpoints.
After installing the driver, I use Bus Hound 5 to send data t...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
Battery life is critical for portable applications. For applications such as smoke detectors, security devices, and thermostats, factory-installed batteries need to last for more than 10 years. The...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
Toyohashi University of Technology demonstrated electric field coupled wireless power supply technology using life-size car tires and roads at the wireless technology exhibition "Wireless Technolog...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
1. When the slip speed regulating motor is undergoing frequency conversion and energy saving transformation, the original excitation box (referred to as the speed regulating box) and the original s...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
0 Introduction
Ultrasonic waves
are mechanical waves with a frequency of more than 20KHz, and the propagation speed in the air is about 340 m/s (at 20°C). Ultrasonic waves can be gene...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
