EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4Q001KG-0139CDI

Description
Programmable Oscillators
CategoryPassive components   
File Size163KB,20 Pages
ManufacturerIDT (Integrated Device Technology)
Download Datasheet Parametric View All

8N4Q001KG-0139CDI Online Shopping

Suppliers Part Number Price MOQ In stock  
8N4Q001KG-0139CDI - - View Buy Now

8N4Q001KG-0139CDI Overview

Programmable Oscillators

8N4Q001KG-0139CDI Parametric

Parameter NameAttribute value
Product AttributeAttribute Value
ManufacturerIDT (Integrated Device Technology)
Product CategoryProgrammable Oscillators
ProductXO
Quad-Frequency Programmable XO IDT8N4Q001 REV G
DATA SHEET
General Description
The IDT8N4Q001 is a Quad-Frequency Programmable Clock
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock® NG technology for
an optimum high clock frequency and low phase noise performance.
The device accepts 2.5V or 3.3V supply and is packaged in a small,
lead-free (RoHS 6) 10-lead ceramic 5mm x 7mm x 1.55mm package.
Besides the four default power-up frequencies set by the FSEL0 and
FSEL1 pins, the IDT8N4Q001 can be programmed via the I
2
C
interface to output clock frequencies between 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz to a very high degree of
precision with a frequency step size of 435.9Hz ÷
N
(N is the PLL
output divider). Since the FSEL0 and FSEL1 pins are mapped to four
independent PLL divider registers (P, MINT, MFRAC and N),
reprogramming those registers to other frequencies under control of
FSEL0 and FSEL1 is supported. The extended temperature range
supports wireless infrastructure, telecommunication and networking
end equipment requirements.
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Four power-up default frequencies (see part number order
codes), re-programmable by I
2
C
I
2
C programming interface for the output clock frequency and
internal PLL control registers
Frequency programming resolution is 435.9Hz ÷N
One 2.5V, 3.3V LVDS clock output
Two control inputs for the power-up default frequency
LVCMOS/LVTTL compatible control inputs
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.253ps
(typical), integer PLL feedback configuration
RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.263ps
(typical), integer PLL feedback configuration
Full 2.5V or 3.3V supply modes
-40°C to 85°C ambient operating temperature
Available in Lead-free (RoHS 6) package
Block Diagram
OSC
f
XTAL
÷MINT,
MFRAC
2
25
FSEL1
FSEL0
SCLK
SDATA
OE
Pulldown
Pulldown
Pullup
Pullup
Pullup
Pin Assignment
÷P
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
÷N
Q
nQ
DNU 1
OE 2
GND 3
FSEL0 4
FSEL1 5
10 SCLK
9 SDATA
8 V
DD
7 nQ
6 Q
7
Configuration Register (ROM)
(Frequency, APR, Polarity)
I
2
C Control
IDT8N4Q001
10-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4Q001GCD
REVISION A
MARCH 6, 2012
1
©2012 Integrated Device Technology, Inc.
Verilog Tutorial
A special tutorial written by a moderator of the NEOIC forum. If you are interested, you can take a look. Very good! Address: Let's learn FPGA together...
shuijian FPGA/CPLD
CCS usage problems and solutions
1. When using CCS to compile,an error message similar to "XXXX line ???: warning: last line of file ends without a newline ?" appears. What should I do?Answer: After the program is completed, it is of...
Jacktang Microcontroller MCU
【FAQ】BQ76930: Battery balancing issue
Q: The values in the cell balance configuration are: Cell balance threshold: 3500mV Cell balance window: 200mV Cell balance minimum: 10mV Battery balancing interval: 4s The CB bit in the balanced conf...
qwqwqw2088 Analogue and Mixed Signal
launchpad simple oscilloscope
This post mainly posts some of my early ideas for using launchpad ~ Simple waveform display ~I have been using 5110 LCD, haha~The main function is to use the ADC of G2231 to collect analog signals and...
juring Microcontroller MCU
Request program modification
:)...
大唐盛世 MCU
2440+7113, why can the camera sometimes receive images but sometimes not?
As the title says, I have developed a 7113 driver under ce. The camera is a BNC port. Why can I get the camera data sometimes but not sometimes? When I can't get the data, I get a completely black ima...
ppm009 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1610  845  1156  1498  1258  33  17  24  31  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号