Default packaging is “Bulk Bag.” An ordering code C-Spec is not required for “Bulk Bag” packaging.
The terms “Marked” and “Unmarked” pertain to laser marking option of capacitors. All packaging options labeled as “Unmarked” will contain
capacitors that have not been laser marked. The option to laser mark is not available on these devices. For more information see “Capacitor Marking.”
2
The 2 mm pitch option allows for double the packaging quantity of capacitors on a given reel size. This option is limited to EIA 0603 (1608 metric) case
size devices. For more information regarding 2 mm pitch option see “Tape & Reel Packaging Information.”
3
Reeling tape options (paper or plastic) are dependent on capacitor case size (l" x w") and thickness dimensions. See "Chip Thickness/Tape & Reel
Packaging Quantities" and "Tape & Reel Packaging Information.”
3
For additional information regarding "AUTO" C-Spec options, see "Automotive C-Spec Information."
3
All automotive packaging C-Specs listed exclude the option to laser mark components. The option to laser mark is not available on these devices.
For more information see "Capacitor Marking.”
Benefits
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
AEC–Q200 automotive qualified
Low dissipation factor DF < 0.1%
Low noise solution similar to C0G
Low ESR and ESL
High thermal stability
High ripple current capability
Preferred capacitance solution at line frequencies and into the MHz range
Retains over 99% of nominal capacitance at full rated voltage
Small predictable and linear capacitance change with respect to temperature
This content is originally created by EEWORLD forum user Qi IC Kan MCU . If you want to reprint or use it for commercial purposes, you must obtain the author's consent and indicate the sourceThe inter...
A: I want to change the communication mode of a product from 422 to 485. I would like to ask my colleagues and TI engineers what factors I should consider, such as the speed?Q: 485 evolved from 422, s...
Shenzhen Jinrunlai Electronics Co., Ltd. is a private limited liability company specializing in the production and processing of 7-core connectors, 10-core connectors, 18-core connectors, 25-core conn...
As the title says, the usage is as follows: the input voltage range is 9-15V, the output voltage is 1/3, the output voltage must change with the input voltage (accuracy is greater than 0.1V), the maxi...
International Solar Photovoltaic Network News: Chinese inverter company Sungrow announced that it will build a 3GW photovoltaic inverter manufacturing plant in Bangalore, the capital of Karnataka, ...[Details]
For 80,000
ZTE
(000063.SZ) employees and more Chinese ICT (information and communication technology) industry practitioners, the news from across the ocean on the evening of April 16 kept t...[Details]
In the actual project development process, we often need to get the running time of a section of code. The usual method is to use an oscilloscope to measure it. This blog post will use SysTick to acc...[Details]
After searching a lot of information, I finally understood the time base timer. I did not use any library functions but operated the registers directly. The following introduces the systick in STM32...[Details]
Timing and protocol are two key points in digital system debugging, and they are also where logic analyzers can play their most valuable role. How can we use a logic analyzer to quickly complete wiri...[Details]
Use the STM32 timer input capture module to control 3-way ultrasonic sensors. The ultrasonic sensor used this time is the common HC-SR04, which is often used in the obstacle avoidance system of smal...[Details]
ADC: 1. The ADC module inside STM32 has three ADC1, ADC2, and ADC3, which are independent of each other, so synchronous sampling can be performed. 2ADC input clock must not exceed 14MHz, it is genera...[Details]
/* Unfortunately, it cannot generate a standard 38kHz frequency square wave, there is a little error*/ #include reg51.h #define uchar unsigned char #define uint unsigned int sbit Waveout=P1^0; //P...[Details]
As shown in the figure, the circuit is required to count and display the number of times the button is pressed. When the button is pressed once, the count value increases by 1 (it is required to accu...[Details]
Circuit: Using AT89S52 single chip microcomputer. P3.0 to P3.3 are connected to four external buttons. P3.4 to P3.7 are the bit selection ports for controlling the four digital tubes, and P1 is the s...[Details]
Please help me analyze the clock cycles occupied by the following delay program. Seek to explain: DELAY: MOV R6, #13 DELAY1: MOV R5, #250 DELAY2: NOP DJNZ R5, DELAY2 DJNZ R6, DEL...[Details]
(1) JTAG is a communication standard used for real-time and fast communication between computers and microcontrollers. The JTAG function of AVR (only available on some models) makes AVR debugging ver...[Details]
:For medium and large-scale domestic photovoltaic power stations, inverters generally go through an open bidding process. Due to the high technical content of power station design, it is necessary ...[Details]
"Now I can't even afford a
memory
stick
to equip my computer
." The price of
memory
sticks has risen rapidly recently. Take 8GB Kingston
memory sticks
as an example. Compared...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
