EEWORLDEEWORLDEEWORLD

Part Number

Search

8429-6

Description
Non-Heat Shrink Tubing and Sleeves 6" 1.27-2.67 Diam connector insulator
CategoryWire/cable   
File Size41KB,3 Pages
Manufacturer3M
Websitehttp://3M.com/esd
Environmental Compliance
Download Datasheet Parametric View All

8429-6 Online Shopping

Suppliers Part Number Price MOQ In stock  
8429-6 - - View Buy Now

8429-6 Overview

Non-Heat Shrink Tubing and Sleeves 6" 1.27-2.67 Diam connector insulator

8429-6 Parametric

Parameter NameAttribute value
Product AttributeAttribute Value
Manufacturer3M
Product CategoryNon-Heat Shrink Tubing and Sleeves
RoHSDetails
TypeCold Shrink
Inside Diameter67.8 mm
ColorBlack
Length152 mm
Factory Pack Quantity10
Unit Weight4.600 lbs
3M™ Cold Shrink Connector
Insulators 8420 Series
Data Sheet
Product
Description
October 2015
3M Cold Shrink Connector Insulators 8420 Series are open-ended, tubular, rubber sleeves which
are factory expanded and assembled onto a removable core. The core is removed after the tube has
been positioned for installation over an inline connection, terminal lug, etc., allowing the tube to
shrink and form a water-resistant seal. The insulating tube is made of EPDM rubber which does not
contain chlorides or sulfur. Six diameter sizes will cover a range of cable up to 1000 volts for copper
and aluminum conductors from 10 AWG through 1000 kcmil.
To extend the useful life of this product in applications which are continuously exposed to high levels
of ultra-violet radiation, overwrap with Scotch® Super 33+™ Vinyl Electrical Tape or Scotch® Self-
Fusing Silicone Rubber Electrical Tape 70.
Features
Simple installation; requires no tools
Accommodates a wide range of cable sizes
No torches or heat required
Good thermal stability
Seals tight; retains its resiliency and pressure even after prolonged years of aging and exposure
Excellent wet electrical properties
Tough rubber formulation withstands backfilling
Water-resistant; Meets the water seal requirements of ANSI C119.1
No mastic or tape required to seal
Resists acids and alkalis; resists ozone
Operating temperature range: -40°F to 194°F (-40°C to 90°C)
Primary electrical insulation for all solid dielectric (rubber and plastic) insulated wire and cable
splicing rated up to 1000 volts
Direct burial and submersible
For indoor and outdoor use
Physical protection and moisture sealing for air-insulated connectors and lugs such as spacer
cable and lug connections to bus bar
Insulation of secondary splices, copper or aluminum conductors
Relocation of service
Dig-in repairs
Sheath repairs
Environmental sealing for communication and other non-electrical applications
Insulation of inline conductor transition connectors
(see Figure 1)
3M™ Cold Shrink Connector Insulator 8426
Applications
2/0
15/16” Connector
Figure 1
4/0
1 of 3
3
16*16 dot matrix screen made of light emitting diodes
I had nothing to do these days, so I used existing materials to make a 16*16 dot matrix screen using yellow light-emitting tubes....
wyhpwg DIY/Open Source Hardware
Some considerations for PCB design to improve mobile phone audio performance
For PCB layout engineers, cell phones present the ultimate challenge. Modern cell phones contain almost every subsystem found in portable devices, and each of these subsystems has conflicting requirem...
黑衣人 PCB Design
MOSFET Power Loss Calculation
I saw TI's web calculation page is very goodIf you need it, you can try it [url]https://webench.ti.com/wb5/FETs_Selection/FETPBWizard.jsp?run=Y[/url]...
dontium Analogue and Mixed Signal
Design of Data Storage System Based on SensorTile - Software Part 1
Continuing from the previous post, read the .tsv file that records sensor data through labvIEW - STMicroelectronics AMG SensorTile Development Competition - Electronic Engineering World - Forum [url=h...
suoma MEMS sensors
Input Bias Current of CMOS and JFET Amplifiers
[p=16, null, left][color=rgb(51, 51, 51)][font=Arial, Helvetica, sans-serif, 宋体][size=12px]We choose CMOS and JFET input op amps, usually because of their low input bias current (IB). But we'll give y...
wstt Microcontroller MCU
How does the Cortex-M4 EPI operate on unaddressed devices?
RT, Zhaxin asks for help....
噗噗__ Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1010  1351  58  1525  905  21  28  2  31  19 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号