HANBit
HFDOM-40LX Series
40Pin Flash Disk Module for 128MB,192M, 256M, True IDE Interface
Mode, 5.0V
Part No. HFDOM40LX-xxxx
GENERAL DESCRIPTION
The HFDOM40LX series 40Pin Flash Disk on Module is a flash technology based with True IDE interface flash memory
card for Lexar controller. It is constructed with flash disk controller chip and NAND-type (Samsung) flash memory device.
The HFDOM40LX series operates in 5.0-Volt power supplies. It comes in capacity of 128, 192MB and up to 256 MB
formatted 40Pin type .
By optimizing flash memory management, the life of this HFDOM40LX series can be extended to its maximum level.
Because the ECC function is included, the correctness of data transfer between the HFDOM40LX series and a True IDE
compatible interface device can be guaranteed.
The HFDOM40LX series is fully compatible with applications such as CPU card / board, set top box, industry / military PC,
security equipment, measuring instrument and embedded systems.
FEATURES
-
-
-
-
-
-
-
-
-
-
-
-
-
True IDE compatible host interface
Direct plug in for 3.5″ IDE Connectors
40 pin 2.54mm IDE Connector
Ultra-High Performance
Support for CIS implemented with 256 bytes of attribute memory
5.0V operation voltage
Burst Rate (to/from Host): up to 16.6MB/s (PIO mode 4)
Sustained Write (Host to flash): minimum of 1.2MB/s
Data Transfer Rate (device to PC via USB interface): up to 850KB/s
Capacity : Min. 128MB ~ Max. 256MB
Auto Sleep Mode
Low Power Dissipation
Low VCC Program Inhibit Function
PRODUCT SPECIFICATIONS
Capacities :
128, 192 and up to 256 MB (formatted)
Operating Voltage :
5.0V ±10%
Power consumptions :
Read mode
Write mode
Sleep mode
65 mA (typ)
65 mA (typ)
300 uA (typ)
0°C to + 70°C
- 25°C to + 85°C
95%(Max)
Environment conditions :
Operating temperature
Storage temperature
Relative humidity
Mechanical conditions :
Weight : Maximum 9.0g
URL : www.hbe.co.kr
REV 1.0 (February, 2003.)
1/1
HANBit Electronics Co., Ltd
.
HANBit
ELECTRICAL SPECIFICATIONS
Table 1.1 Absolute Maximum Ratings
Parameters
Storage Temperature
Power Supply Voltage
Symbol
Tstg
Vcc
Min
-65
-0.3
Max
150
7
HFDOM-40LX Series
Unit
°C
V
Test Condition
Input or Output Voltage
Vin, Vout
Gnd-0.5
Vcc+0.5
V
NOTE :Stress
above those listed under Absolute Maximum Ratings may cause permanent
damage to the device. This is a stress rating only and functional operation of the
device at these or any conditions above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions for extended periods may affect device
reliability.
Table 1.2 Recommended Operating Conditions
Parameters
Operating Temperature
Supply Voltage
Symbol
Ta
Vcc
Min
0
4.5
Max
70
5.5
Unit
°C
V
Test Condition
Table 1.3 DC Characteristics
(Ta = 0 to +70°C, Vcc = 5V
±
10%, Vcc = 3V
±
5%)
Parameters
Power Supply voltage
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
Input Leakage
Output Capacitance
Read Current
Write Current
Sleep Current
Symbol
Vdd
Vil
Vih
Vol
Voh
Il
Cout
Irc
Iwr
Isc
Min
3.15
-0.5
2.0
-
2.4
-5
-
Max
5.5
0.8
Vdd+0.3
0.4
-
5
10
55
55
200
Unit
V
V
V
V
V
uA
pF
mA
mA
uA
Test Condition
CAPACITY SPECIFICATIONS
Table 1.4 Capacity Specifications
Part Number
HFDOM-40LX128
HFDOM-40LX192
HFDOM-40LX256
Capacity
(Unformatted)
Sectors/Card
Cylinders
Heads
Sectors/Track
128,188,416
bytes
193,462,272
bytes
257,949,696
bytes
250,368
377,856
503,808
978
738
984
8
16
16
32
32
32
URL : www.hbe.co.kr
REV 1.0 (February, 2003.)
2/2
HANBit Electronics Co., Ltd
.
HANBit
PHYSYCAL SPECIFICATIONS
HFDOM-40LX Series
51.70±0.1mm
Jumper
22.10±0.1mm
29.10±0.2mm
Slave
1,2
Close
7.0±0.1mm
1
Master
2,3
Close
+
-
1
2
3
Jumper
POWER
55.37±0.1mm
< View from front side >
3.8±0.1mm
2.54±0.05mm
6.0±0.1mm
2.54±0.05mm
48.20±0.1mm
55.30±0.1mm
< View from connector side >
Figure 1.1 40 pin Type Flash Disk Module Dimensions
INSTALLTION GUIDE
URL : www.hbe.co.kr
REV 1.0 (February, 2003.)
3/3
HANBit Electronics Co., Ltd
.
HANBit
HFDOM-40LX Series
1) Setting Method
(for example)
①
②
Make sure your computer is turned off before you open the case.
Plug the carefully into the 40pin IDE slot on your computer.
Caution:
Make sure to align pin1 on host adapter interface connector with pin 1 on your Flash Disk Module. Pin 1
is indicated by a triangle on the Flash Disk Module connector.
The Flash Disk Module is used power connector cable of the computer.
Caution:
If you need to remove your Flash Disk Module, use both hands to pull it out carefully.
Check all cable connections and then replace your computer cover.
③
④
2) BIOS setting Method
(for example)
Before you format or partition your new drive, you must configure your computer's BIOS so that the computer can
recognize your new drive.
①
Turn your computer on. As your computer start up, watch the screen for a message describing how to run the
system setup program on the screen (sometimes called BIOS or CMOS setup). This is usually done by pressing a
special key, such as
Delete, Esc
or
F1
during startup. See your computer manual for details. Press the appropriate
key to run the system setup program.
If your BIOS provides automatic drive detection (an "AUTO" drive type), select this option.
(
We
recommend to use Normal / CHS mode to partition your Flash Disk Module to get the maximum formatted
capacity.
)
This allows your computer to configure itself automatically for your new drive.
If your BIOS dose not provide “AUTO” drive detection, select "User-defined" drive setting and enter the
CHS values from the table.
BIOS Settings (see specification) Capacity Cylinders Heads Sectors(unformatted)
Save the settings and exit the System Setup program. ( your computer will automatically reboot ) After you
configure your computer, you can use the standard DOS commands to partition and format your Flash Disk Module,
as described below.
②
③
3)
Formatting Method
(for example)
To partition your new Flash Disk Module with Microsoft DOS program :
①
②
Insert a bootable DOS diskette into your diskette drive and restart your computer.
Insert a DOS program diskette that contains the
FDISK.EXE
and
FORMAT.COM
programs into your diskette drive. Use the same DOS version that is on your bootable diskette. At the
A:\ >
prompt,
type
“FDISK”
and press
Enter.
Select
“Create DOS partition or logical DOS drive”
by pressing
1.
Then press
Enter.
Select
“Create primary DOS partition”
by pressing
1
again. Then press
Enter.
Create your first drive partition. If you are creating a partition that will be used to boot your computer (drive C),
make sure that the partition is marked active.
Create an extended partition and additional logical drives as necessary, until all the space on your new hard drive
has been partitioned.
When the partitioning is complete,
FDISK
reboots your computer.
Caution:
Make sure to use the correct drive letters so that you do not format a drive that already contains data.
At the
A:\ >
prompt, type
“format c:/s”,
where
c
is
HFDOM40LX,
Repeat the format process for all the new
partitions you have created.
After you format your drive, it is ready to use.
③
④
⑤
⑥
⑦
⑧
1. PIN INFORMATION
URL : www.hbe.co.kr
REV 1.0 (February, 2003.)
4/4
HANBit Electronics Co., Ltd
.
HANBit
PIN ASSIGNMENTS AND PIN TYPE
Table 2.1 Pin Assignment and Pin type
Pin
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Signal
/RESET
D07
D06
D05
D04
D03
D02
D01
D00
GND
DREQ
/OW
/OR
IOCHRDY
/DACK
INT
A01
A00
/CS0
/DASP (LED)
Pin Type
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
GND
DREQ
/OW
/OR
IORDY
/DACK
IRQ
I
I
CS0
I/O
Pin
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
HFDOM-40LX Series
Signal
GND
D08
D09
D10
D11
D12
D13
D14
D15
NC
GND
GND
GND
H_SEL
GND
/IO16
/PDIAG
A02
/CS1
GND
Pin Type
GND
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
KEY(no pin)
GND
GND
GND
CSEL
GND
/IOIS16
I/O
I
I
GND
URL : www.hbe.co.kr
REV 1.0 (February, 2003.)
5/5
HANBit Electronics Co., Ltd
.
京公网安备 11010802033920号
EEWORLD
