Spec No. JENF243J-0006B-01
Reference Only
P1/9
CHIP NOISE FILTER
1. Scope
NFZ2HBM□□□SN10L REFERENCE SPECIFICATION
This reference specification applies to NFZ2HBM_SN10L, Chip Noise Filter.
.
2. Part Numbering
(ex)
NF
Z
2Ｈ
Ｂ
M
Characteristics
１Ｒ５
S
N
Category
1
0
L
Product ID Structure Dimension
(L×W)
Typical Impedance Performance
at 100MHz
Numbers special Packaging
of
speci- L:Taping
Circuit
fication *B: BULK
*B: Bulk packing also available
3. Rating
・Operating
Temperature Range
・Storage
Temperature Range
– 55°C to + 125°C
– 55°C to + 125°C
Impedance at 1MH½
Customer
Part Number
MURATA
Part Number
(Ω
)
Tolerance
DC Resistance
(Ω
)
Tolerance.
Emission noise
Restraint frequency
(recommendation,MHz)
Rated Current *1
(A)
NFZ2HBM1R5SN10L
NFZ2HBM2R9SN10L
NFZ2HBM4R4SN10L
NFZ2HBM6R1SN10L
NFZ2HBM8R4SN10L
NFZ2HBM110SN10L
NFZ2HBM170SN10L
NFZ2HBM240SN10L
NFZ2HBM330SN10L
NFZ2HBM600SN10L
1.5
2.9
4.4
6.1
8.4
11
17
24
33
60
±30%
0.060
0.085
0.105
0.125
0.145
0.160
0.210
0.250
0.300
0.300
±25%
1.20
1.10
1.05
1.00
0.90
0.80
0.70
0.65
0.50
0.40
130-200
110-150
85-130
75-110
70-90
60-80
50-70
45-65
40-55
30-50
*1: When applied Rated current to the Products, self temperature rise shall be limited to 20℃ max.
Typical value is actual performance.
4. Testing Conditions
《Unless
otherwise specified》
《In
case of doubt》
Temperature : Ordinary Temperature / 15°C to 35°C
Temperature : 20°C ± 2°C
: Ordinary Humidity
/ 25%(RH) to 85%(RH)
Humidity
: 60%(RH) to 70%(RH)
Humidity
Atmospheric Pressure : 86kPa to 106kPa
5. Appearance and Dimensions
0.6 ± 0.2
■
Unit Mass (Typical value)
0.022g
0.9 ± 0.1
2.5 ± 0.2
2.0 ± 0.2
(in mm)
MURATA MFG.CO., LTD
Spec No. JENF243J-0006B-01
Reference Only
Specification
Impedance shall meet item 3.
P2/9
6. Electrical Performance
No.
6.1
Item
Impedance
Test Method
Measuring Equipment:
KEYSIGHT
4991A or equivalent
(1mA)
Measuring Frequency: 1MHz
Measuring Equipment: Digital multi meter
Digital multi meter
(TR6846 or equivalent)
a
terminal1
SW
b
terminal2
6.2
DC Resistance
DC Resistance shall meet item 3.
DC resistance shall be measured after putting chip
noise filter between the terminal 2 under the condition
of opening between a and b.
Every measurement the terminal 1 shall be shorted
between a and b when changing noise filter.
7. Mechanical Performance
No.
7.1
Item
Shear Test
Specification
Chip noise filter shall not be damaged
after tested as follows.
Test Method
Applied Direction
Chip Noise Filter
Chip Coil
F
Substrate
7.2
Bending Test
Force: 10N
Hold Duration: 5s±1s
Applied Direction: Parallel to PCB
Substrate: Glass-epoxy substrate
(100mm×40mm×1.0mm)
Solder: Reflow
Pressure jig
R230
F
Deflection
Product
(in mm)
45
45
7.3
Vibration
7.4
Drop
Speed of Applying Force: 0.5mm / s
Deflection: 2mm
Hold Duration: 30 s
Oscillation Frequency:
10Hz to 2000Hz to 10Hz for 20 min
Total amplitude 3.0 mm or Acceleration
amplitude 245m/s
2
whichever is smaller.
Testing Time:
A period of 4h in each of 3 mutually
perpendicular directions.
It shall be dropped on concrete or steel
board.
Method : free fall
Height : 1m
Total of 10 cycles
MURATA MFG.CO., LTD
Spec No. JENF243J-0006B-01
No.
7.5
Item
Solderability
Reference Only
Specification
The wetting area of the electrode
shall be at least 90% covered with
new solder coating.
P3/9
7.6
Resistance to
Soldering Heat
Appearance: No damage
Impedance Change: within ±30%
Test Method
Flux: Ethanol solution of rosin 25(wt)%
(Immersed for 5s to 10s)
Solder: Sn-3.0Ag-0.5Cu
Pre-Heating: 150°C±10°C / 60s to 90s
Solder Temperature: 240°C±5°C
Immersion Time: 3s±1s
Flux: Ethanol solution of rosin 25(wt)%
(Immersed for 5s to 10s)
Solder: Sn-3.0Ag-0.5Cu
Pre-Heating: 150°C±10°C / 60s to 90s
Solder Temperature: 270°C±5°C
Immersion Time: 10s±1s
Then measured after exposure in the room
condition for 24h±2h.
8. Environmental Performance
It shall be soldered on the substrate.
No.
Item
Specification
8.1 Heat Resistance
Appearance: No damage
Impedance Change: within ±30%
Test Method
Temperature: 125°C±2°C
Time: 1000h (+48h,-0h)
Then measured after exposure in the room
condition for 24h±2h.
Temperature: -55°C±2°C
Time: 1000h (+48h,-0h)
Then measured after exposure in the room
condition for 24h±2h.
Temperature: 40°C±2°C
Humidity: 90%(RH) to 95%(RH)
Time: 1000h (+48h,-0h)
Then measured after exposure in the room
condition for 24h±2h.
1 cycle:
1 step: -55°C±2°C / 30 min±3 min
2 step: Ordinary temp. / 10 min to 15 min
3 step: 125°C±2°C / 30 min to 3 min
4 step: Ordinary temp. / 10 min to15 min
Total of 100cycles
Then measured after exposure in the room
condition for 24h±2h.
8.2
Cold Resistance
8.3
Humidity
8.4
Temperature
Cycle
MURATA MFG.CO., LTD
Spec No. JENF243J-0006B-01
Reference Only
P4/9
9. Specification of Packaging
9.1 Appearance and Dimensions of plastic tape
(8mm-wide)
φ1.5±
0.1
0
2.0±0.05
4.0±0.1
4.0±0.1
1.75±0.1
1.1±0.1
0.25±0.05
3.5±0.05
2.8±0.1
8.0±0.2
(in mm)
2.3±0.1
Direction of feed
φ1.0+0.1
-0
Dimension of the Cavity is measured at the bottom side.
9.2 Specification of Taping
(1) Packing quantity (standard quantity)
3,000 pcs / reel
(2) Packing Method
Products shall be packed in the each embossed cavity of plastic tape and sealed by cover tape.
(3) Sprocket hole
The sprocket holes are to the right as the tape is pulled toward the user.
(4) Spliced point
Plastic tape and Cover tape has no spliced point.
(5) Missing components number
Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater,
and are not continuous. The Specified quantity per reel is kept.
9.3 Pull Strength
Plastic tape
Cover tape
10N min.
5N min.
9.4 Peeling off force of cover tape
Speed of Peeling off
Peeling off force
300mm / min
Plastic tape: 0.1N to 0.7N
(minimum value is typical)
165 to 180 degree
F
Cover tape
Plastic tape
9.5 Dimensions of Leader-tape, Trailer and Reel
There shall be leader-tape (cover tape) and trailer-tape (empty tape) as follows.
Trailer
2.0±0.5
160 min.
Leader
Label
190 min.
Empty tape
13.0±0.2
210 min.
Cover tape
60±
0
21.0±0.8
1
9±
1
0
13±1.4
180±
3
0
Direction of feed
(in mm)
MURATA MFG.CO., LTD
Spec No. JENF243J-0006B-01
9.6 Marking for reel
Customer part number, MURATA part number, Inspection number (1), RoHS marking (2),
Quantity etc
½½½
1)
<Expression of Inspection No.>
(1)
Factory Code
(2)
Date
First digit
Reference Only
□□
OOOO
(1)
(2)
(3)
P5/9
: Year / Last digit of year
Second digit
: Month / Jan. to Sep.
1 to 9, Oct. to Dec.
O, N, D
Third, Fourth digit : Day
(3)
Serial No.
2)
<Expression of RoHS marking >
(1)
RoHS regulation conformity parts.
(2)
MURATA classification number
ROHS – Y (△)
(1) (2)
9.7 Marking for Outside package (corrugated paper box)
Customer name, Purchasing order number, Customer part number, MURATA part number,
RoHS marking (2), Quantity, etc
½½½
9.8 Specification of Outer Case
Outer Case Dimensions
(mm)
W
D
H
186
186
93
Standard Reel Quantity
in Outer Case (Reel)
Label
H
D
W
5
Above
Outer Case size is typical. It depends on a quantity of an order
10.
！
Caution
Limitation of Applications
Please contact us before using our products for the applications listed below which require especially
high reliability for the prevention of defects which might directly cause damage to the third party's life,
body or property.
(1) Aircraft equipment
(6) Transportation equipment (vehicles, trains, ships, etc.)
(2) Aerospace equipment
(7) Traffic signal equipment
(3) Undersea equipment
(8) Disaster prevention / crime prevention equipment
(4) Power plant control equipment (9) Data-processing equipment
(5) Medical equipment
(10) Applications of similar complexity and /or reliability
requirements to the applications listed in the above
11. Notice
This product is designed for solder mounting.
Please consult us in advance for applying other mounting method such as conductive adhesive.
11.1 Land pattern designing
Chip Noise
Chip coil
Filter
Land
Solder Resist
a
b
c
1.6
3.0
2.1
(in mm)
MURATA MFG.CO., LTD
京公网安备 11010802033920号
EEWORLD
