ALUMINUM ELECTROLYTIC CAPACITORS
UZS
Specifications
Item
4.5mmL Chip Type
UWX
Smaller
Chip type with 4.5mm height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
UZT
High
Te m p e rature
UZS
Smaller
UZR
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan
δ)
–40 to + 85°C
4 to 50V
1 to 220µF
–
+ 20% at 120Hz, 20°C
After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01 CV or 3 (µA) ,whichever is greater.
Rated voltage (V)
tan
δ
(MAX.)
4
0.50
4
7
15
6.3
0.30
6.3
4
8
10
0.24
10
3
8
Measurement frequency : 120Hz at 20°C
16
25
35
50
0.19
0.16
0.14
0.14
Measurement frequency : 120Hz
Stability at Low Temperature
Rated voltage (V)
Z– 25°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
16
2
4
25
2
4
35
2
3
50
2
3
Endurance
The specifications listed at right shall be met when
the capacitors are restored to 20°C after the rated
voltage is applied for 2000 hours at 85°C.
Capacitance change
tan
δ
Leakage current
Within
+
20% of the initial capacitance value
–
200% or less than the initial specified value
Less than or equal to the initial specified value
Shelf Life
Resistance to soldering
heat
Marking
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
Capacitance change
Within
+
10% of the initial capacitance value
–
maintained at 250°C. The capacitors shall meet the
Less than or equal to the initial specified value
tan
δ
characteristic requirements listed at right when they are
Less than or equal to the initial specified value
Leakage current
removed from the plate and restored to 20°C.
Black print on the case top.
Chip Type
Positive
Voltage
C ±0.2
0.5 MAX.
Capacitance
Lot No.
Plastic platform
0.3 MAX.
Type numbering system (Example : 16V 10
µ
F)
1
2
3
4
5
6
7
8
9 10 11 12 13 14
U Z S 1 C 1 0 0 MC L 1 GB
Taping code
4.5
Voltage mark for 6.3V is
6V .
+0.1
–0.2
0.5 to 0.8
Negative
φD
A
B
C
E
4
1.8
4.3
4.3
1.0
5
2.1
5.3
5.3
1.3
(mm)
6.3
2.4
6.6
6.6
2.2
A±0.3
E
A±0.3
Configuration
Capacitance tolerance (+ 20%)
–
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Type
A2
10
16V
φD±0.5
Dimensions
V
Cap. (µF)
Code
4
0G
B±0.2
6.3
0J
10
1A
16
1C
25
1E
35
1V
4
4
4
5
6.3
50
1H
8.4
13
17
20
33
1
2.2
3.3
4.7
10
22
33
47
100
220
010
2R2
3R3
4R7
100
220
330
470
101
221
4
4
5
6.3
28
33
56
96
4
5
5
6.3
28
37
45
70
5
5
6.3
33
41
52
4
5
6.3
6.3
23
37
49
58
4
5
6.3
6.3
16
27
42
52
4
5
6.3
18
29
46
Case size
φ
D (mm)
Rated
ripple
Rated ripple current (mArms) at 85°C 120Hz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.70
120 Hz
1.00
300 Hz
1.17
1 kHz
1.36
10 kHz or more
1.50
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please select UUR(p.154), UUG(p.160) if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
108
京公网安备 11010802033920号
EEWORLD
