51740-10400404CCLF datasheet, PDF

Datasheet> All Categories > The connector> 51740-10400404CCLF

51740-10400404CCLF: DescriptionPower to the Board 4P 4S 4P PF Vertical Receptacle; CategoryThe connector; File Size91KB，13 Pages; ManufacturerFCI / Amphenol; Environmental Compliance

Download Datasheet Parametric View All

51740-10400404CCLF Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	51740-10400404CCLF	-	-	View	Buy Now

51740-10400404CCLF Overview

Power to the Board 4P 4S 4P PF Vertical Receptacle

51740-10400404CCLF Parametric

Parameter Name	Attribute value
Product Attribute	Attribute Value
Manufacturer	FCI / Amphenol
Product Category	Power to the Board
RoHS	Details
Contact Gender	Socket (Female)
Current Rating	30 A
Voltage Rating	2.5 kV Power, 1 kV Signal
Number of Positions	8 Power, 4 Signal
Mounting Style	Through Hole
Termination Style	Press Fit
Packaging	Tray
Housing Material	Thermoplastic
Mounting Angle	Vertical
Number of Rows	4 Row
Contact Arrangement	Power/Signal/Power
Row Spacing	6.35 mm Power, 2.54 mm Signal
Insulation Resistance	10000 MOhms
Maximum Operating Temperature	+ 105 C
Minimum Operating Temperature	- 20 C
Factory Pack Quantity	33

Preview

Download Datasheet

View All

NUMBER

TYPE

GS-12-149

TITLE

PRODUCT SPECIFICATION

PAGE

REVISION

PwrBlade

Product Specification

1 of 13

AUTHORIZED BY

DATE

29 Jul 16

MT Ruan

CLASSIFICATION

UNRESTRICTED

1.0

OBJECTIVE

This specification defines the performance, test, quality and reliability requirements of the PwrBlade

Connector System.

2.0

SCOPE

This specification is applicable to the termination characteristics of separable right angle and vertical headers

when mated to the right angle and vertical receptacles.

3.0

GENERAL

If there is conflict between the product drawings and specifications, the drawing takes precedence.

This document is composed of the following sections:

Paragraph

1.0

2.0

3.0

4.0

5.0

5.1

5.2

5.3

5.4

5.5

6.0

7.0

8.0

9.0

9.1

9.2

9.3

9.4

9.5

9.6

10.0

Table 2

Title

OBJECTIVE

SCOPE

GENERAL

APPLICABLE DOCUMENTS

REQUIREMENTS

Qualification

Material

Finish

Design and construction

Workmanship

ELECTRICAL CHARACTERISTICS

MECHANICAL CHARACTERISTICS

ENVIRONMENTAL CONDITIONS

QUALITY ASSURANCE PROVISIONS

Equipment Calibration

Inspection Conditions

Sample Quality and Description

Acceptance

Qualification Testing

Re-qualification Testing

Reference Documents

Qualification Testing Matrix

Form E-3334

Rev F

PDS: Rev :AA

GS-01-001

STATUS:Released

Printed: Jul 29, 2016

NUMBER

TYPE

GS-12-149

TITLE

PRODUCT SPECIFICATION

PAGE

REVISION

PwrBlade

Product Specification

5 of 13

AUTHORIZED BY

DATE

29 Jul 16

MT Ruan

CLASSIFICATION

UNRESTRICTED

7.3

Contact Retention – Individual power and signal contacts shall withstand an axial retention load of

13.4N [3 pound]. Individual signal receptacle contacts will withstand an axial load of 26.7N [6 pound]

minimum to seat further into housing.

a. Rate of 12.7mm [0.5 inch] per minute without dislodging from the housing cavity.

b. Test 30 contacts

c. As per MIL-STD-1344A, Method 2007.1.

7.4

Individual Pin Insertion/Retention Force - The force required to insert an individual compliant pin into

a plated through hole in a printed circuit board at a rate of 5.08mm [0.2 inch] per minute shall not

exceed 26.6N [6 pound] for signal receptacle contacts, 93.4N [21 pound] for signal header pins and

111.2N [25 pound] per tail for power contacts . The retention force in the axial direction opposite that

of insertion shall not be less than 6.7N [1.5 pound] for signal receptacle contacts, 13.4N [3 pound] for

signal header pins and 22.3N [5 pound] per tail for power contacts.

Table 3: Individual Pin Insertion/Retention Force table

Pwr contact

(per tail)

111.2N [25lbs]

22.3N [5lbs]

Signal contact

Rec Signal contact

26.6N [6lbs]

6.7N [1.5lbs]

Hdr Signal contact

93.4N [21lbs]

13.4N [3lbs]

Force spec.

Insertion force Maximum

Retention force Minimum

7.5

PCB Hole Deformation Radius

Power Contacts – cross-section parallel to board surface. Photograph and measure the hole

deformation (deformation on board material) radius at a point 0.254mm [0.010”] from the surface, and

the center of the compliant pin section. Include 10 holes. The average (of 10 holes) hole deformation

radius shall be no greater than0.0381mm [0.0015”] when measured from the drilled hole. The

absolute maximum deformation radius shall not exceed 0.0508mm [0.002”].

Signal Contacts

Signal Receptacle Contacts – Reference FCI BUS-12-111 – HPC Solderless (Press Fit) Right Angle

Receptacles

Signal Header Contacts – Same as the requirement for Power Contacts above

7.6

PCB Hole Wall Damage – Cross-section perpendicular to the board surface, and through the

compliant section wear track. Photograph and measure the copper thickness remaining between the

compliant section and the printed wiring board laminate. Include 10 holes. The minimum average (of

10 holes) copper thickness remaining between the compliant pin and the printed wiring board

laminate shall not be less than 0.00762mm [0.0003”]. In addition there shall be no copper cracks,

separations between conductive interfaces, or laminate-to-copper separations.

Form E-3334

Rev F

PDS: Rev :AA

GS-01-001

STATUS:Released

Printed: Jul 29, 2016

Recommended Resources

The ammeter is connected to the circuit through the current transformer phase switch and switches c

Tower indicator circuit

MAX4166-4167 low-power, high-output driver integrated operational amplifier

Small battery charger with selectable charging time

555 practical electronic mouse trap circuit

Measurement amplifier circuit using programmable integrated operational amplifier

Overview of Virtual Instrument Drivers: The application of computers in the field of testing and automation has led to the birth of the concept of instrument "drivers", which are also called driver programs. The instrument is a software mid...; feifei Test/Measurement

Is there any IAR compiler environment for STM32F7?: I bought the official STM32F7 board, but I don't know how to use it. Is there an IAR compilation environment for STM32F7?...; xiaos200800 stm32/stm8

Problems with Bluetooth Low Energy modules: I am now making a remote control that uses a Bluetooth low energy module. I found a low-power Bluetooth module, DX-BT19-S.When connected, it is 8.5mA, when not connected, it is 400-700uA. This low pow...; chenbingjy Wireless Connectivity

Understanding of feedback and operational amplifiers in circuits: Feedback: It can be described as sending part or all of the output (voltage or current) of the amplifier circuit back to the input of the amplifier circuit in a certain way. We sometimes call the ampl...; Jacktang Analogue and Mixed Signal

Microcontroller and microprocessor market continues to grow: The expansion of consumer demand and technological advancement in the industrial field continue to drive the rapid growth of the microcontroller and microprocessor market. The key factor causing its e...; 朗锐智科 Robotics Development

What is the maximum power that TPS2491 can control?: What is the maximum power that the TPS2491 can control?What is the maximum power that the TPS2491 can control? TPS2491 uses an external MOSFET. Question: Can TPS2491 stably control an application with...; xujian2000 Analogue and Mixed Signal

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components