EEWORLDEEWORLDEEWORLD

Part Number

Search

WRM0207Y-243RBI

Description
MELF Resistors
CategoryPassive components   
File Size456KB,3 Pages
ManufacturerTT Electronics
Download Datasheet Parametric View All

WRM0207Y-243RBI Overview

MELF Resistors

WRM0207Y-243RBI Parametric

Parameter NameAttribute value
Product AttributeAttribute Value
ManufacturerTT Electronics
Product CategoryMELF Resistors
Mounting StylePCB Mount
Resistors
MELF Resistors
WRM Series
AEC-Q200
High reliability
Predictable pulse handling capability
Tolerances down to 0.1%
TCR down to 5 ppm/°C
All parts are Pb-free and comply with EU Directive 2011/65/EU amended by (EU) 2015/863 (RoHS3)
Electrical Data
Power rating @70°C
Resistance Range
Limiting element voltage
TCR
Resistance tolerance
Standard values
Thermal impedance
Ambient temperature range
Insulation resistance
Zero ohm jumper current rating
Zero ohm jumper maximum residual resistance
watts
ohms
volts
ppm/°C
%
k/W
°C
ohms
amps
mΩ
WRM 0102
0.2
8R2 - 1M0
200
15, 25, 50, 100
WRM 0204
WRM 0207
0.25
0.4
R22 -5M1
R22 - 10M
200
250
5, 10, 15, 25, 50, 100
15, 25, 50, 100
0.1, 0.25, 0.5, 1, 5
E24 & E96
200
140
-55 to +125
>10
10
4
15
250
-55 to +155
2
Physical Data
Dimensions (mm) & weight (g)
Type
WRM 0102
WRM 0204
WRM 0207
L
max
2.3
3.7
6.1
D
max
1.35
1.55
2.4
D
1
max
1.3
1.55
2.4
K
min
0.3
0.5
0.5
L
1
min
1.1
1.5
2.9
Weight
0.01
0.02
0.08
L
D
1
L
1
K
D
Construction
A metal film is deposited onto a high dissipation ceramic
former to which tin plated teminating caps are fitted.
The resistor is adjusted to value by a helical cut in the film
and the body is protected by a lacquer coating.
Terminations
Material
Solderability
Marking
Plated steel cap.
The pure tin finish produces ageing free
contacts on which low melting solders can
be used. Dipped area shall be covered with
a smooth and bright solder coating after
3 seconds immersion at 215°C.
Resistance values are colour coded with four bands,
three indicating value and one indicating the multiplier.
(Note this describes standard marking, but certain values
may still be supplied with the addition of a tolerance
band following the multiplier.).
Solvent Resistance
The body protection and marking are resistant to all normal
industrial cleaning solvents suitable for printed circuit boards.
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
BI Technologies IRC Welwyn
www.ttelectronics.com/resistors
© TT Electronics plc
07.18
USB disk repair tool for SP2233 solution
On Friday, a colleague's USB flash drive was damaged. I checked it and it was SP2233 solution. I have its repair tool. I fixed it. Very good. I dare not keep it to myself. I will share it with you....
西门 Test/Measurement
[New version CH554 review DIY] Audio Tuner 3
1. According to the information of the new version of the development board, you need to install the driver first and use ISP to write. 2. In the initial process, the download was not successful accor...
北方 MCU
Summary of DSP's real clock system--Explained with TI's DSP TMS320F2812 as an example
Learn programming standards from TI code!!! In fact, it is quite important to understand the system clock system. The following is a brief summary of the key points of the application. 1. First of all...
灞波儿奔 DSP and ARM Processors
Cheap_Flash_FS Express Edition--Embedded NandFlash File System Source Code Download
Cheap_Flash_FS Express Edition--Embedded NandFlash File System Source Code Download This code has been developed by us and has been rigorously tested. The bad block management function includes a mana...
figureyang12345 stm32/stm8
lattice FPGA LFXP2-5E-6TN144C chip
I just bought a development board. There are real LVDS modules on both sides of the chip, and virtual LVDS modules on the upper and lower parts. But in actual operation, why is the voltage difference ...
whllieying FPGA/CPLD
Transplanting ucosII to AT91SAM7S64, the delay function is invalid after running
Transplanting ucosII to AT91SAM7S64, the delay function is invalid after running, please ask the master to make the clock beat valid...
l0700830216 Real-time operating system RTOS

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1458  938  2576  1295  2239  30  19  52  27  46 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号