EEWORLDEEWORLDEEWORLD

Part Number

Search

LAS36340JLF

Description
Wirewound Resistors - Through Hole
CategoryPassive components   
File Size356KB,3 Pages
ManufacturerTT Electronics
Download Datasheet Parametric View All

LAS36340JLF Overview

Wirewound Resistors - Through Hole

LAS36340JLF Parametric

Parameter NameAttribute value
Product AttributeAttribute Value
ManufacturerTT Electronics
Product CategoryWirewound Resistors - Through Hole
TechnologyWirewound
Mounting StylePCB Mount
Resistors
Low Cost Semi-Precision
Power Wirewound Resistor
Low Cost Semi-Precision
LAS Series
Power Wirewound Resistor
1 and 3 watts
0.1 ohm
LAS Series
to 18K ohms
1
Color
watts
identification
and 3
band
0.1 ohm to 18K ohms
±5%, ±3%, ±1%, ±.5% tolerance
Color band identification
Resistance wire TCR ±20 ppm/°C
±5%, ±3%, ±1%, ±.5% tolerance
RoHS-compliant version available
Resistance wire TCR ±20 ppm/°C
RoHS-compliant version available
½llo½ resistance wirewound
to speci½ic parameters includin½
TCR½s ½rom ±20 to ½5500 ppm/°C
½ll welded
cap and lead
Colorband
½ar½in½
All Pb-free parts comply with EU Directive 2011/65/EU (RoHS2)
Heat conductin½
ceramic substrate
Silicone
con½ormal coatin½
Electrical Data
IRC
Type
LAS-1
LAS-3
Power Rating 275°C
Max. Hot Spot
125°C
1
2
25°C
2
3
Commercial Range
(ohms)
Min.
0.1
0.1
Max.
7.5K
18K
Non-Inductive Range
(ohms)
Min.
0.1
0.2
Max.
3.8K
7.5K
Available Resistance
(ohms)
0.5%, 1%
1 - 7.5K
1 - 18K
3%, 5%
0.1 - 7.5K
0.1 - 18K
Environmental Data
Test Condition (@ 25°C)
Load Life 1000 hours
Moisture Resistance
Temperature Cycle
Short Time Overload
Low Temperature Operation
Solder Heat
Shock
Vibration
LAS-3 Carbon Comp Replacement (contact factory)
The L½S-3 is a three watt con½ormal coated precision wirewound resistor. The resistance wire is welded to the end caps and
wound on alumina rod ½or ½ood thermal conductivit½. In circuit applications that utilize two watt carbon comp resistors the L½S-3
is an idead e½½ective replacement. The L½S-3 5.6 ohm can be specificall½ desi½ned to withstand 22 jooules o½ ener½½ delivered
b½ a 1000 volt 10 x 1000 usec wave shape pulse.
LIGHTNING SURGE
Special L½S-3 5.6 ohm to 100 ohm will meet
Telecom GR-1089 li½htnin½ requirements.
V = 1000 volts
T1 = 10 usec rise
T2 = 1000 usec to V2
10 ohm output impedance
V
Max
∆R
1.0%
1.0%
0.5%
0.5%
0.5%
0.25%
0.5%
0.5%
V2
0
T1
MICROSECONDS
T2
General Note
IRC reserves the right to make changes in product specification without notice or liability.
General Note
All information is subject to IRC’s own data and is considered accurate at time of going to print.
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going
Wire and Film Technologies Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
to print.
BI Technologies IRC Welwyn
A subsidiary of
TT electronics plc
http://www.ttelectronics.com/resistors
LAS Series Issue October 2008 Sheet 1 of 3
© TT Electronics plc
04.17
Can TVS be used to extinguish arcs?
Relays and other equipment will arc during operation due to the influence of induced electromotive force. In this way, relays are prone to failure. In practice, RC circuits are used to suppress arcing...
bigbat Motor Drive Control(Motor Control)
Principle and Application of Fieldbus Temperature Transmitter
I. Introduction The rapid development of information technology has led to changes in the structure of automation systems, and has gradually formed an enterprise information system based on network in...
songbo Embedded System
Help: How to use Altera FFT IP core on FPGA board
I use FPGA to implement a spectrum analyzer and use the on-chip FFP IP core to perform spectrum analysis. I calculate the square sum of the real and imaginary parts and take the logarithm to generate ...
when_Qi FPGA/CPLD
MPLAB editor has red lines everywhere
The code is all red line alarm, but the compilation can pass, please solve it... It affects the programming too much, I thought it was all wrong...
apleilx Microchip MCU
How to remove the seal?
[i=s]This post was last edited by paulhyde on 2014-9-15 03:17[/i] It has just been blocked, how can I unblock it?...
bophic Electronics Design Contest
[Homemade op amp] Can anyone recommend some books or materials on making op amps? [I would like to thank TAT]
Because I need to make an op amp myself recently, but I feel that the static operating points are not set well, and the effect is not good. . What I mean by making an op amp is to use transistors dire...
cinbow Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2459  1603  2258  32  2714  50  33  46  1  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号