• Distributes one clock input to one bank of five and one bank of
four outputs
• Separate output enable for each output bank
• Output Skew < 250ps
• Low jitter <200 ps cycle-to-cycle
• IDT23S09E-1 for Standard Drive
• IDT23S09E-1H for High Drive
• No external RC network required
• Operates at 3.3V V
DD
• Spread spectrum compatible
• Available in SOIC and TSSOP packages
NOTE: EOL for non-green parts to occur on 5/13/10 per
PDN U-09-01
The IDT23S09E is a high-speed phase-lock loop (PLL) clock buffer,
designed to address high-speed clock distribution applications. The zero
delay is achieved by aligning the phase between the incoming clock and
the output clock, operable within the range of 10 to 200MHz.
The IDT23S09E is a 16-pin version of the IDT23S05E. The IDT23S09E
accepts one reference input, and drives two banks of four low skew clocks.
The -1H version of this device operates up to 200MHz frequency and has
higher drive than the -1 device. All parts have on-chip PLLs which lock
to an input clock on the REF pin. The PLL feedback is on-chip and is
obtained from the CLKOUT pad. In the absence of an input clock, the
IDT23S09E enters power down. In this mode, the device will draw less
than 12µA for Commercial Temperature range and less than 25µA for
Industrial temperature range, and the outputs are tri-stated.
The IDT23S09E is characterized for both Industrial and Commercial
operation.
FUNCTIONAL BLOCK DIAGRAM
16
CLKOUT
1
REF
PLL
2
CLKA1
3
CLKA2
14
CLKA3
15
CLKA4
S2
S1
8
9
Control
Logic
6
CLKB1
7
CLKB2
10
CLKB3
11
CLKB4
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
1
c
2006 Integrated Device Technology, Inc.
AUGUST 2009
DSC - 6399/11
IDT23S09E
3.3V ZERO DELAY CLOCK BUFFER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
PIN CONFIGURATION
REF
CLKA1
CLKA2
V
DD
GND
CLKB1
CLKB2
S2
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
SOIC/ TSSOP
TOP VIEW
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
Rating
Supply Voltage Range
Input Voltage Range (REF)
Input Voltage Range
(except REF)
I
IK
(V
I
< 0)
I
O
(V
O
= 0 to V
DD
)
V
DD
or GND
T
A
= 55°C
(in still air)
(3)
T
STG
Operating
Temperature
Operating
Temperature
Storage Temperature Range
Commercial Temperature
Range
Industrial Temperature
Range
-40 to +85
°C
–65 to +150
0 to +70
°C
°C
Input Clamp Current
Continuous Output Current
Continuous Current
Maximum Power Dissipation
Max.
–0.5 to +4.6
–0.5 to +5.5
–0.5 to
V
DD
+0.5
–50
±50
±100
0.7
mA
mA
mA
W
Unit
V
V
V
CLKOUT
CLKA4
CLKA3
V
DD
GND
CLKB4
CLKB3
S1
V
DD
V
I (2)
V
I
APPLICATIONS:
•
•
•
•
•
SDRAM
Telecom
Datacom
PC Motherboards/Workstations
Critical Path Delay Designs
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. The input and output negative-voltage ratings may be exceeded if the input and output
clamp-current ratings are observed.
3. The maximum package power dissipation is calculated using a junction temperature
of 150°C and a board trace length of 750 mils.
PIN DESCRIPTION
Pin Name
REF
(1)
CLKA1
(2)
CLKA2
V
DD
GND
CLKB1
(2)
CLKB2
(2)
S2
(3)
S1
(3)
CLKB3
(2)
CLKB4
(2)
(2)
Pin Number
1
2
3
4, 13
5, 12
6
7
8
9
10
11
14
15
16
Type
IN
Out
Out
PWR
GND
Out
Out
IN
IN
Out
Out
Out
Out
Out
Functional Description
Input reference clock, 5 Volt tolerant input
Output clock for bank A
Output clock for bank A
3.3V Supply
Ground
Output clock for bank B
Output clock for bank B
Select input Bit 2
Select input Bit 1
Output clock for bank B
Output clock for bank B
Output clock for bank A
Output clock for bank A
Output clock, internal feedback on this pin
CLKA3
(2)
CLKA4
(2)
CLKOUT
(2)
NOTES:
1. Weak pull down.
2. Weak pull down on all outputs.
3. Weak pull ups on these inputs.
2
IDT23S09E
3.3V ZERO DELAY CLOCK BUFFER
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES
FUNCTION TABLE
(1)
S2
L
L
H
H
S1
L
H
L
H
CLKA
Tri-State
Driven
Driven
Driven
CLKB
Tri-State
Tri-State
Driven
Driven
CLKOUT
(2)
Driven
Driven
Driven
Driven
Output Source
PLL
PLL
REF
PLL
PLL Shut Down
N
N
Y
N
NOTES:
1. H = HIGH Voltage Level.
L = LOW Voltage Level
2. This output is driven and has an internal feedback for the PLL. The load on this ouput can be adjusted to change the skew between the REF and the output.
DC ELECTRICAL CHARACTERISTICS - COMMERCIAL
Symbol
V
IL
V
IH
I
IL
I
IH
V
OL
V
OH
I
DD_PD
I
DD
Parameter
Input LOW Voltage Level
Input HIGH Voltage Level
Input LOW Current
Input HIGH Current
Output LOW Voltage
Output HIGH Voltage
Power Down Current
Supply Current
V
IN
= 0V
V
IN
= V
DD
Standard Drive
High Drive
Standard Drive
High Drive
REF = 0MHz (S2 = S1 = H)
Unloaded Outputs at 66.66MHz, SEL inputs at V
DD
or GND
I
OL
= 8mA
I
OL
= 12mA (-1H)
I
OH
= -8mA
I
OH
= -12mA (-1H)
—
—
12
32
µA
mA
2.4
—
V
Conditions
Min.
—
2
—
—
—
Max.
0.8
—
50
100
0.4
Unit
V
V
µA
µA
V
OPERATING CONDITIONS - COMMERCIAL
Symbol
V
DD
T
A
C
L
C
IN
Supply Voltage
Operating Temperature (Ambient Temperature)
Load Capacitance < 100MHz
Load Capacitance 100MHz - 200MHz
Input Capacitance
Parameter
Min.
3
0
—
—
—
Max.
3.6
70
30
10
7
pF
Unit
V
°
C
pF
SWITCHING CHARACTERISTICS (23S09E-1) - COMMERCIAL
(1,2)
Symbol
t
1
Output Frequency
Duty Cycle = t
2
÷
t
1
t
3
t
4
t
5
t
6A
t
6B
t
7
t
J
t
LOCK
Rise Time
Fall Time
Output to Output Skew
Delay, REF Rising Edge to CLKOUT Rising Edge
(2)
Delay, REF Rising Edge to CLKOUT Rising Edge
(2)
Device-to-Device Skew
Cycle-to-Cycle Jitter
PLL Lock Time
Parameter
10pF Load
30pF Load
Measured at 1.4V, F
OUT
= 66.66MHz
Measured between 0.8V and 2V
Measured between 0.8V and 2V
All outputs equally loaded
Measured at V
DD
/2
Measured at V
DD
/2 in PLL bypass mode (IDT23S09E only)
Measured at V
DD
/2 on the CLKOUT pins of devices
Measured at 66.66MHz, loaded outputs
Stable power supply, valid clock presented on REF pin
AT89C51 is connected to ULN2003 to drive the relay, and the relay is connected to the inverter to control the oil field water injection pump motor. Is it possible? How to connect the circuit diagram?...
I want to encode the input double-bit information, for example, change 00 to 11, 01 to 1-1, 11 to -1-1, 10 to -11, and apply the 1 and -1 to subsequent operations. I want to know how to deal with this...
Hello, I am new to 430 microcontrollers, so I am sorry to ask you a simple question.How do I set the status register SR in the MSP430 microcontroller using the register method?For example, I want to s...
I'm looking for help! I recently learned about NDIS drivers. Following the example in Chapter 9 by Wang Yanping, I installed an NDIS protocol driver: protoDrv.sys. However, the application failed to c...
[align=left] [/align] [align=left] [/align][align=left][font=微软雅黑]When it comes to PCB circuit design, there will be times when you need to replace IC chips. Here are some tips on replacing IC chips t...
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
With the rapid development of science and technology, especially the widespread application of digital technology and various ultra-large-scale integrated circuits, electronic equipment, especially...[Details]
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
As a wireless broadband metropolitan area network standard, WiMAX technology has greater advantages than previous 3.5GHz MMDS products in terms of non-line-of-sight transmission and spectrum utiliz...[Details]
No matter which processor you are learning, the first thing you need to understand is the registers and working mode of the processor.
ARM has 37 registers, including 31 general registers and ...[Details]
introduction
MAX6636 is a multi-channel precision temperature monitor that can not only monitor local temperature, but also connect up to 6 diodes externally. Each channel has a programmable...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
Liquid crystal display (LCD) panels have a wide range of applications, from small portable electronic devices to large fixed devices, including digital cameras, laptops, personal data assistants, d...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
When the so-called "copycat phones" that flood the domestic mobile phone market move towards large screens, stereo amplifiers, touch controls, and even GPS navigation and mobile TV, the homogeneity...[Details]
1 Introduction
Power supply ripple will interfere with the normal operation of electronic equipment, causing malfunctions such as computer crashes, data processing errors and control system fa...[Details]
1. Introduction
AS-Interface bus technology is an intelligent network that uses a single cable to connect sensors and actuators to controllers, transmit data, and provide power. It can be used...[Details]
Synchronous buck designs are becoming increasingly difficult, and the selection of suitable ICs is becoming quite narrow. This Design Idea combines a current-mode PWM IC used in a flyback regulator...[Details]
For a long time, my country has implemented "community-style collective heating" for hot water heating, and settled accounts based on the heating area, regardless of whether the user uses heat. Thi...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
