C512C339J1R5CA datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > C512C339J1R5CA

Preview

C512C339J1R5CA: DescriptionCERAMIC MOLDED/AXIAL & RADIAL - STANDARD; File Size135KB，10 Pages; ManufacturerKEMET; Websitehttp://www.kemet.com

Download Datasheet View All

C512C339J1R5CA Overview

CERAMIC MOLDED/AXIAL & RADIAL - STANDARD

Preview

Download Datasheet

View All

CERAMIC MOLDED AXIAL & RADIAL

PERFORMANCE CHARACTERISTICS

GENERAL

Working Voltage:

C0G – 50, 100 & 200 Volts

X7R – 50, 100 & 200 Volts

Temperature Characteristics:

C0G – 0 ±30 PPM/°C from -55°C to +125°C

X7R – ±15% from -55°C to +125°C

Capacitance Tolerance:

C0G – ±0.5 pF, ±1%, ±2%, ±5%, ±10%, ±20%

(±0.5 pF is tightest available tolerance)

X7R – ±10%, ±20%, -0 +100%, -20% +80%

Construction:

Monolithic block of ceramic dielectric with interdigitated

internal electrodes, encapsulated in a molded case, and

having axial or radial leads. Meets flame test requirements

of UL Standard 94V-0.

Terminal Strength:

EIA-198 Method 303 Condition A (2.2 kg)

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current

limited to 50 mA.

ENVIRONMENTAL

Moisture Resistance:

MIL-STD-202, Method 106, or EIA-198, Method 204,

Condition A, except 20 cycles.

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current

limited to 50 mA.

Immersion Cycling:

MIL-STD-202, Method 104, Condition B. Post-Test limits

at 25°C are:

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Solderability:

MIL-STD-202, Method 208, Sn62 solder, 245°C for 5 ±1/2

seconds.

Resistance to Soldering Heat:

MIL-STD-202, Method 210, Condition B (260°C, 10 secs).

Depth of immersion — to a minimum of .050" from the

capacitor body.

Lead Material:

Axial: Solder-coated copper clad steel

Radial: Solder-coated copper standard; 100% tin plated optional

ELECTRICAL

Capacitance:

Within specified tolerance when measured with 1 volt rms

at 1 kHz (1000 pF or less at 1 MHz for C0G).

Dissipation Factor:

25°C at 1 kHz (1000 pF or less at 1 MHz for C0G).

C0G – .15% maximum

X7R – 2.5% maximum

Insulation Resistance:

After 2 minutes electrification at 25°C and rated voltage

C0G – 100K megohms or 1000 megohm - µF, whichever

is less.

X7R – 100K megohms or 1000 megohm - µF, whichever

is less.

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current limited

to 50 mA at 25°C.

Life Test:

2000 hours at 200% of rated voltage at 125°C. Post-Test

limits at 25°C are:

Capacitance Change:

C0G – less than 3% or 0.25 pF, whichever is higher

X7R – ±20% of initial value

Dissipation Factor:

C0G – .25% maximum

X7R – 3.0% maximum

Recommended Resources

electronic whistle circuit

Fuse blown centralized monitoring circuit 2

Equal sub-wave transmitter circuit with power 1W

Short circuit protection circuit for 380V power supply control circuit_1

Large dynamic range voltage controlled amplifier circuit

50 ohm linear amplifier circuit

National College Student Electronic Design Competition Experience Exchange----[Signal Source Category]: [i=s]This post was last edited by paulhyde on 2014-9-15 03:44[/i] [color=#7b7d72][font=Arial, sans-serif](1) In July, a national expert group working meeting was held to preliminarily determine the ba...; paulhyde Electronics Design Contest

【Design Tools】FPGA Getting Started Tutorial: Introduces the principles of FPGA devices, development process and simple design examples for your referenceUse QUARTUS II to do the whole process of FPGA development. The detailed fool-proof tutorial...; shower.xu FPGA/CPLD

[TI recommended course] #Zero-based entry: Hand-in-hand teaching you how to quickly develop MSP430? Project#: //training.eeworld.com.cn/TI/show/course/5649...; EricCheng TI Technology Forum

MSP430: I use IAR environment to program MSP430F6433 microcontroller and encounter the following two problems. Please help me. (1) When waking up from low power mode LPM3.5, according to the manual, there sho...; zilong Microcontroller MCU

A novice asks for help. I encountered a problem when connecting to the simulator after evc4.0 compilation!: I downloaded the code of an MP3 player from the Internet. It should be the built-in media player of wince5.0. It can be compiled under EVC4.0, but a dialog box pops up when I start the simulator after...; lsx2002 Embedded System

Why is Quiescent Current (Iq) Important for USB Type-C?: [align=left][color=#000]USB Type-C has become a hot topic after the launch of new laptops, smartphones and tablets; all of these devices have Type-C ports that can be used for both charging and connec...; maylove Analogue and Mixed Signal

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components