EEWORLDEEWORLDEEWORLD

Part Number

Search

PLL620-80DI

Description
Low Phase Noise XO (9.5-65MHz Output)
File Size205KB,7 Pages
ManufacturerETC
Download Datasheet Compare View All

PLL620-80DI Overview

Low Phase Noise XO (9.5-65MHz Output)

PLL620-80
Low Phase Noise XO (9.5-65MHz Output)
FEATURES
19MHz to 65MHz crystal input.
Output range: 9.5MHz – 65MHz
Selectable OE Logic (enable high or enable low).
Available outputs: PECL, LVDS, or CMOS (High
Drive (30mA) or Standard Drive (10mA) output).
Supports 2.5V or 3.3V Power Supply.
Available in die form.
DIE CONFIGURATION
OUTSEL0^
65 mil
OUTSEL1^
Reserved
VDD
VDD
VDD
VDD
N/C
(1550,1475)
17
16
25
24
23
22
21
20
19
18
GNDBUF
CMOS
LVDSB
PECLB
VDDBUF
VDDBUF
PECL
LVDS
OE_SEL^
XIN
XOUT
N/C
62 mil
26
27
Die ID:
A2020-20B
15
28
14
DESCRIPTION
The PLL620-80 is a XO IC specifically designed to
work with fundamental or 3
rd
OT crystals between
19MHz and 65MHz. The selectable divide by two
feature extends the operation range from 9.5MHz to
65MHz. It requires very low current into the crystal
resulting in better overall stability. The OE logic
feature allows selection of enable high or enable low.
Furthermore, it provides selectable CMOS, PECL or
LVDS outputs.
S2^
OE
CTRL
N/C
13
29
12
11
30
C502A
31
1
2
3
4
5
6
7
8
10
9
Reserved
Y
(0,0)
X
OUTPUT SELECTION AND ENABLE
OUT_SEL1*
(Pad 18)
0
0
1
1
OE_SELECT
(Pad 9)
0
1 (Default)
OUT_SEL0*
(Pad 25)
0
1
0
1
OE_CTRL
(Pad 30)
0
1 (Default)
0 (Default)
1
Selected Output*
High Drive CMOS
Standard CMOS
LVDS
PECL (default)
State
Tri-state
Output enabled
Output enabled
Tri-state
DIE SPECIFICATIONS
Name
Size
Reverse side
Pad dimensions
Thickness
Value
62 x 65 mil
GND
80 micron x 80 micron
10 mil
BLOCK DIAGRAM
OE
Q
XIN
XOUT
Oscillator
Amplifier
Q
S2
PLL620-80
Pads #9, #18 & #25: Bond to GND to set to “0”,
No connection results to “default” setting
through internal pull-up.
OE_CTRL: Logical states defined by PECL levels if OE_SELECT is “1”
Logical states defined by CMOS levels if OE_SELECT is “0”
OUTPUT FREQUENCY SELECTOR
S2
0
1(Default)*
*Internally set to ‘Default’ through 60K
Output
Input/2
Input
pull-up resistor
47745 Fremont Blvd., Fremont, California 94538 Tel (510) 492-0990 Fax (510) 492-0991
www.phaselink.com
Rev 11/09/04 Page 1
GNDBUF
GNDBUF
GND
GND
GND
GND
GND

PLL620-80DI Related Products

PLL620-80DI P620-80DC PLL620-80 PLL620-80DC
Description Low Phase Noise XO (9.5-65MHz Output) Low Phase Noise XO (9.5-65MHz Output) Low Phase Noise XO (9.5-65MHz Output) Low Phase Noise XO (9.5-65MHz Output)
[Problem Feedback] Error and warning message issues in TangDynasty ChipWatcher
If there are errors or warnings during the use or compilation of TangDynasty, the corresponding information will be displayed through the Error or Warning at the bottom, and there will be a correspond...
littleshrimp Domestic Chip Exchange
Does anyone have the SVPWM waveform of CCS? I need it urgently.
It would be best if there are 3-4 waveforms with the part marked. Thank you. As long as the SVPWM waveform debugged by CCS is...
zwwlyshen Microcontroller MCU
There is a problem about repeated definition in the program, please answer
Error[e27]: Entry "Delay5ms" in module play ( F:\工程\Debug\Obj\play.r43 ) redefined in module playmain ( F:\工程\Debug\Obj\playmain.r43 ) Specifically, I have void Delay5ms (void) in my play.c, and then ...
Jiaoeeer Microcontroller MCU
Why is it still not working after following the tutorial?
I used Zstack to modify the code according to the tutorial, and then compiled and ran it correctly, but it didn't work when I downloaded it to the development board, and I couldn't see what was wrong....
三生三世枕上书 RF/Wirelessly
The role of Y capacitor in electromagnetic disturbance
What role does the Y capacitor play in power supply design? Which part is closely related to EMI design? In which designs and applications are leakage currents of particular concern? Let's continue re...
qwqwqw2088 Analogue and Mixed Signal
Wince novice: Error when building a new project: Command returned non-zero exit code 1 (dec), please help
An error occurred when building the run-time image. Please help me. I saw on the Internet that I checked the checkbox in Project->Properties->Configuration Properties->Build Option->Run-time image can...
annirojess Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2377  2603  1124  1892  405  48  53  23  39  9 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号