C114C12022G5CA datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > C114C12022G5CA

Preview

C114C12022G5CA: DescriptionCERAMIC MOLDED/AXIAL & RADIAL - STANDARD; File Size135KB，10 Pages; ManufacturerKEMET; Websitehttp://www.kemet.com

Download Datasheet View All

C114C12022G5CA Overview

CERAMIC MOLDED/AXIAL & RADIAL - STANDARD

Preview

Download Datasheet

View All

CERAMIC MOLDED AXIAL & RADIAL

PERFORMANCE CHARACTERISTICS

GENERAL

Working Voltage:

C0G – 50, 100 & 200 Volts

X7R – 50, 100 & 200 Volts

Temperature Characteristics:

C0G – 0 ±30 PPM/°C from -55°C to +125°C

X7R – ±15% from -55°C to +125°C

Capacitance Tolerance:

C0G – ±0.5 pF, ±1%, ±2%, ±5%, ±10%, ±20%

(±0.5 pF is tightest available tolerance)

X7R – ±10%, ±20%, -0 +100%, -20% +80%

Construction:

Monolithic block of ceramic dielectric with interdigitated

internal electrodes, encapsulated in a molded case, and

having axial or radial leads. Meets flame test requirements

of UL Standard 94V-0.

Terminal Strength:

EIA-198 Method 303 Condition A (2.2 kg)

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current

limited to 50 mA.

ENVIRONMENTAL

Moisture Resistance:

MIL-STD-202, Method 106, or EIA-198, Method 204,

Condition A, except 20 cycles.

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current

limited to 50 mA.

Immersion Cycling:

MIL-STD-202, Method 104, Condition B. Post-Test limits

at 25°C are:

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Solderability:

MIL-STD-202, Method 208, Sn62 solder, 245°C for 5 ±1/2

seconds.

Resistance to Soldering Heat:

MIL-STD-202, Method 210, Condition B (260°C, 10 secs).

Depth of immersion — to a minimum of .050" from the

capacitor body.

Lead Material:

Axial: Solder-coated copper clad steel

Radial: Solder-coated copper standard; 100% tin plated optional

ELECTRICAL

Capacitance:

Within specified tolerance when measured with 1 volt rms

at 1 kHz (1000 pF or less at 1 MHz for C0G).

Dissipation Factor:

25°C at 1 kHz (1000 pF or less at 1 MHz for C0G).

C0G – .15% maximum

X7R – 2.5% maximum

Insulation Resistance:

After 2 minutes electrification at 25°C and rated voltage

C0G – 100K megohms or 1000 megohm - µF, whichever

is less.

X7R – 100K megohms or 1000 megohm - µF, whichever

is less.

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current limited

to 50 mA at 25°C.

Life Test:

2000 hours at 200% of rated voltage at 125°C. Post-Test

limits at 25°C are:

Capacitance Change:

C0G – less than 3% or 0.25 pF, whichever is higher

X7R – ±20% of initial value

Dissipation Factor:

C0G – .25% maximum

X7R – 3.0% maximum

Recommended Resources

Application circuit of HA11226

Sound controlled toy low light circuit

Linear Analog Coupler

ISD1016A loop playback circuit

HTE series (2100BQ, 2104BQ) integrated circuits

Low-cost power factor correction circuit using IGBT as switch

[Original serial] JZ2440 study notes 1-transplant u-boot-2015.04 to support jz2440's nor flash: [b][font=华文仿宋][size=16pt]JZ2440[font=华文仿宋] study notes[/font][/size][/font][/b][align=center] [/align][align=center]Chili[/align][align=center] [/align][align=center]2015.5[/align][align=center] [/ali...; ChiliWang Linux and Android

RF Signal Power Detector: I accidentally embarked on the road of no return for RF hardware design. I have some relatively simple questions. Recently, I am using the LTC5507 power detector of Lingte Company. I want to realize t...; logitech66 RF/Wirelessly

【Showing goods】The fourth wave: Today is Sunday again, and it’s time to sweep the dust off the development board. I’ll show it off here as well.This content is originally created by EEWORLD forum user ddllxxrr . If you want to repri...; ddllxxrr Special Edition for Assessment Centres

TI CC2640R2F already supports AOA, do you want to try it out?: I just saw a question post about Bluetooth 5.1 on TI E2E and figured out a problem:A: Has your company launched chips that support Bluetooth 5.1? TI FAE : CC2652R . A: It seems to be Bluetooth 5.0, no...; 3228 Wireless Connectivity

【New Year, New Resolution】Persistence: In the new year, I will change my previous lifestyle and habits and redefine my life. 1. Work hard to learn embedded systems, and after learning STM32, I will move on to FPGA. 2. Practice programming ...; czs111 Talking

Nine performance characteristics of LED driver power supply: [hide]1. High reliability, especially for the driver power supply of LED street lamps, which is installed at high altitude, it is inconvenient to maintain and the maintenance cost is also high. 　　2. H...; 探路者 LED Zone

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components