C062C229F1R5CA datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > C062C229F1R5CA

Preview

C062C229F1R5CA: DescriptionCERAMIC MOLDED/AXIAL & RADIAL - STANDARD; File Size135KB，10 Pages; ManufacturerKEMET; Websitehttp://www.kemet.com

Download Datasheet View All

C062C229F1R5CA Overview

CERAMIC MOLDED/AXIAL & RADIAL - STANDARD

Preview

Download Datasheet

View All

CERAMIC MOLDED AXIAL & RADIAL

PERFORMANCE CHARACTERISTICS

GENERAL

Working Voltage:

C0G – 50, 100 & 200 Volts

X7R – 50, 100 & 200 Volts

Temperature Characteristics:

C0G – 0 ±30 PPM/°C from -55°C to +125°C

X7R – ±15% from -55°C to +125°C

Capacitance Tolerance:

C0G – ±0.5 pF, ±1%, ±2%, ±5%, ±10%, ±20%

(±0.5 pF is tightest available tolerance)

X7R – ±10%, ±20%, -0 +100%, -20% +80%

Construction:

Monolithic block of ceramic dielectric with interdigitated

internal electrodes, encapsulated in a molded case, and

having axial or radial leads. Meets flame test requirements

of UL Standard 94V-0.

Terminal Strength:

EIA-198 Method 303 Condition A (2.2 kg)

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current

limited to 50 mA.

ENVIRONMENTAL

Moisture Resistance:

MIL-STD-202, Method 106, or EIA-198, Method 204,

Condition A, except 20 cycles.

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current

limited to 50 mA.

Immersion Cycling:

MIL-STD-202, Method 104, Condition B. Post-Test limits

at 25°C are:

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Solderability:

MIL-STD-202, Method 208, Sn62 solder, 245°C for 5 ±1/2

seconds.

Resistance to Soldering Heat:

MIL-STD-202, Method 210, Condition B (260°C, 10 secs).

Depth of immersion — to a minimum of .050" from the

capacitor body.

Lead Material:

Axial: Solder-coated copper clad steel

Radial: Solder-coated copper standard; 100% tin plated optional

ELECTRICAL

Capacitance:

Within specified tolerance when measured with 1 volt rms

at 1 kHz (1000 pF or less at 1 MHz for C0G).

Dissipation Factor:

25°C at 1 kHz (1000 pF or less at 1 MHz for C0G).

C0G – .15% maximum

X7R – 2.5% maximum

Insulation Resistance:

After 2 minutes electrification at 25°C and rated voltage

C0G – 100K megohms or 1000 megohm - µF, whichever

is less.

X7R – 100K megohms or 1000 megohm - µF, whichever

is less.

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current limited

to 50 mA at 25°C.

Life Test:

2000 hours at 200% of rated voltage at 125°C. Post-Test

limits at 25°C are:

Capacitance Change:

C0G – less than 3% or 0.25 pF, whichever is higher

X7R – ±20% of initial value

Dissipation Factor:

C0G – .25% maximum

X7R – 3.0% maximum

Recommended Resources

STK4141 II power amplifier circuit diagram

Pure DC current negative feedback power amplifier circuit made by LM3886TF

Application circuit of CAT3606

KA2211 audio IC circuit

Resistor bridge amplifier circuit

8W amplifier

Comic sequence control: Share a comic book Sequential Control [[i] This post was last edited by Changjianze1 on 2011-4-12 10:47 [/i]]...; 常见泽1 Integrated technical exchanges

STM32F103 serial port 2 output is incorrect: [size=3]A novice is learning STM32. After completing the code, he found that the serial port 1 sends and receives normally, but the serial port 2 sends abnormally (the simulation runs in single step, ...; kermit stm32/stm8

[Domestic RISC-V Linux board Fang·Starlight VisionFive trial report] C language programming to control WS2812B colorful lamp beads: The RISC-V single-board computer used in this trial provides us with 40 pin interfaces, including the SPI interface. WhatI want to share today is how to use SPI to drive the ws2812B colorful lamp bead...; HonestQiao Domestic Chip Exchange

The AD voltage check has been completed, how to connect it to the LED: 1. Battery voltage detection . 2. Voltage displayed on LCD1602 3. When the voltage is lower than 2.6V, the indicator light flashes. 4. When the voltage is higher than 3.3V, the indicator light flashes...; 新晋电子发廋友 51mcu

Mechanical and electrical system testing and control from entry to mastery: "Electromechanical System Testing and Control from Entry to Mastery" is aimed at the professional knowledge background of undergraduate graduates majoring in electromechanical engineering. First, in t...; arui1999 Download Centre

Heart-shaped water lamp made with single-chip microcomputer and PCB diagram: Heart-shaped water lamp made with single-chip microcomputer and PCB diagram...; 恒河沙ZSF 51mcu

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components