EEWORLDEEWORLDEEWORLD

Part Number

Search

LKSN2562MESC

Description
Aluminum Electrolytic Capacitors - Snap In 5600uF 20% 56V Audio Smaller SnapIn
CategoryPassive components   
File Size266KB,4 Pages
ManufacturerNichicon
Websitehttp://www.nichicon.co.jp
Environmental Compliance
Download Datasheet Parametric View All

LKSN2562MESC Online Shopping

Suppliers Part Number Price MOQ In stock  
LKSN2562MESC - - View Buy Now

LKSN2562MESC Overview

Aluminum Electrolytic Capacitors - Snap In 5600uF 20% 56V Audio Smaller SnapIn

LKSN2562MESC Parametric

Parameter NameAttribute value
Product AttributeAttribute Value
ManufacturerNichicon
Product CategoryAluminum Electrolytic Capacitors - Snap In
RoHSDetails
ProductAudio Grade Electrolytic Capacitors
Termination StyleSnap In
Capacitance5600 uF
Voltage Rating DC56 VDC
Tolerance20 %
Minimum Operating Temperature- 40 C
Maximum Operating Temperature+ 85 C
Number of Pins2 Pin
Diameter35 mm
Length25 mm
Lead Spacing10 mm
Life1000 Hour
Ripple Current3.2 A
PackagingBulk
Dissipation Factor DF0.3
Factory Pack Quantity200
Test Frequency120 Hz
ALUMINUM ELECTROLYTIC CAPACITORS
LKS
Snap-in Terminal Type,
For Audio Equipment, Smaller-sized
Smaller and high-tone quality than LKG TYPE-
1
grade.
An effect to tone quallity improvement by replacement from
a small standard product to use.
Compliant to the RoHS directive (2011/65/EU).
LKG
TYPE -1
Smaller
LKS
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan
δ)
Stability at Low Temperature
40 to +85°C
Performance Characteristics
25 to 100V
680 to 33000µF
± 20% at 120Hz, 20°C
See refer to next page (Measurement frequency : 120Hz at 20°C)
Rated voltage(V)
3
CV
3 CV
After 5 minutes' application of rated voltage
at 20°C
, leakage current is not more than
3 CV
(µA),
[C : Rated Capacitance(µF), V : Voltage ( V ) ]
25 to 100
4
12
Capacitance change
tan
δ
Leakage current
Measurement frequency : 120Hz
Impedance ratio ZT/Z20(MAX.)
Z
25°C/ Z+20°C
Z
40°C/ Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 85°C.
Within ±20% of the initial value
200% or less than the initial specified value
Less than or equal to the initial specified value
Shelf Life
Marking
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause
4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
Printed with silver color letter on black sleeve.
Drawing
Polarity bar
Sleeve (P.E.T.)
Type numbering system (Example : 35 V 8200µF)
1
2
3
4
5
6
7
8
9 10 11
12
L K S 1 V 8 2 2 ME S A
φ
D
+1MAX.
Case dia.code
Configuration
L
±2
6.3±1
(1
0)
Capacitance tolerance (±20%)
Rated capacitance (8200
µ
F)
Rated voltage (35V)
Series name
Type
Pressure relief vent
φD
20
22
25
30
35
Code
Y
Z
A
B
C
10
±
0.
0.8
- 0.1
6.3 ±1
3.5
+0.2
0
.2
+ 0 .1
.8
- 0
1
2-2
φ±
0.1
(PC board hole dimensions)
1.5
+0.2
- 0.1
(Terminal dimensions)
Dimension table in next page.
365
LPC2104_flash.icf or LPC2104_ram.icf file
I am currently developing ARM7LPC series chips. When using IAR development environment, I am missing LPC2104_flash.icf or LPC2104_ram.icf files. Does anyone have similar configuration files? I would b...
wpx7lsdfn NXP MCU
[AN-1150 Application Note] Using the Traditional Knob Interface to Control the AD5111/AD5113/AD5115
Introduction: Digital potentiometers are the best alternative to mechanical potentiometers because of their small package size, higher reliability, high accuracy, and smaller voltage glitches....
EEWORLD社区 ADI Reference Circuit
What are the simple methods to measure inductance?
Because small inductance cannot be measured with an inductance meter, and even if it can be measured, the error is very large, so is there any other method? Tell me in detail, preferably with a schema...
huacong5419 FPGA/CPLD
【CC2650STK】It's the weekend, let's upload some information and discuss the issue of downloading and debugging
After carefully looking at the schematic diagram, I found that cc2650stk uses the jtag interface to communicate with devpack. And the devpack is recognized as xds110 on the PC.Suddenly I found that th...
人民币的幻想 Wireless Connectivity
TI Award-winning Live Broadcast: Talking about "packaged antenna" smart millimeter wave sensors, even novices can handle industrial robots
If industrial robots want to avoid collisions in a large area ( brother, don't touch porcelain for no reason ), they need to be able to sense in all directions ( up and down, left and right ). TI mill...
nmg TI Technology Forum
Ask about the conflict between 6410 dual network cards
The platform uses s3c6410, wince6.0 operating system, wifi uses sdio8686, and LAN uses dm9000ae. If any single network card is enabled and the others are disabled, everything will run normally. Howeve...
mingboal Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1226  1880  2208  2453  10  25  38  45  50  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号