EEWORLDEEWORLDEEWORLD

Part Number

Search

BF1908-10RJI

Description
RESISTOR, WIRE WOUND, 23 W, 1; 2; 5; 10 %, 75; 120 ppm, 1 ohm - 40 ohm
CategoryPassive components   
File Size327KB,7 Pages
ManufacturerWelwyn (TT Electronics plc)
Websitehttp://www.welwyn-tt.com/index.asp
Download Datasheet Parametric View All

BF1908-10RJI Overview

RESISTOR, WIRE WOUND, 23 W, 1; 2; 5; 10 %, 75; 120 ppm, 1 ohm - 40 ohm

BF1908-10RJI Parametric

Parameter NameAttribute value
Maximum operating temperature375 Cel
stateACTIVE-UNCONFIRMED
Rated temperature20 Cel
Manufacturer Series
Resistor typeRESISTOR
Operating Voltage140 V
Tubular Vitreous Enamelled
Wirewound Resistors
1600/1900 Series
Welwyn Components
Impervious lead free vitreous enamel coating
Can be supplied with fixed, adjustable,
tapped or low inductance winding
Seven termination styles with choice of
mounting arrangements
Manufactured RoHS compliant
Pb-free terminations*
* Check status of stock when ordering
General Information
Vitreous enamelled wirewound resistors are capable of
withstanding a higher dissipation size for size, than any other
protected type; this is attributable to the higher operating
temperature which the wire and enamel can withstand.
Vitreous enamel provides exceptionally good protection to the
wire element and is essentially impervious to moisture. The
resistors can safely be used in harsh environmental conditions.
The Welwyn range is based on thirteen sizes of tube, each of
which has a recommended maximum dissipation which limits
operating surface temperature to a maximum of 375°C.
The stability and high reliability of Welwyn tubular vitreous
resistors is a direct result of the best quality materials being
used in their construction.
High purity ceramic tubes have been matched with nickel
chromium resistance wires and specially formulated enamel to
ensure that the resistors can withstand repeated heat cycling
without damage.
Connections between the resistance element and end
terminations are welded; other connections are brazed.
Mounting devices are available which permit resistors to be
mounted by both ends or by one end. Single ended mounting
is recommended for applications which do not subject the
resistor to shock or vibration.
Ferrules and the F type mounting plug are anchored into the
tubes with high temperature adhesive.
Special requirements, for types or styles not described
in this brochure, will be considered for economic
quantities.
Electrical Data
Power rating at 70°C
Resistance range
Limiting element voltage
TCR (-55 to +200°C)
Resistance tolerance
Values
Thermal impedance
Operating temperature range
watts
ohms
volts
ppm/°C
%
°C/watt
°C
1605
47
1601
11
1905
16
1602
1906
1603
1604
17
22
25
35
See Table 1
See Table 1
Typically: <+75
Maximum + 200
1, 2, 5, 10
See table 1 for value restrictions
E24 preferred
See fig. 1
-55 to +375
1908
54
1607
1606
76
91
See Table 1
See Table 1
1608
115
1609
165
1600
16.5
Power rating at 70°C
Resistance range
Limiting element voltage
TCR (-55 to +200°C)
Resistance tolerance
Values
Thermal impedance
Operating temperature range
watts
ohms
volts
ppm/°C
%
Typically: <+75
1, 2, 5, 10
°C/watt
°C-55 to +375
Maximum + 150
See table 1 for value restrictions
E24 preferred
See fig. 1
Note
See Figure 1 for curves of temperature rise / watts dissipation.
General Note
Welwyn Components reserves the right to make changes in product specification without notice or liability.
All information is subject to Welwyn’s own data, relates to current manufacture and is considered accurate at time of going to print.
A subsidiary of
TT electronics plc
Issue E · 10.05
© Welwyn Components Limited
· Bedlington, Northumberland NE22 7AA, UK
Telephone: +44 (0) 1670 822181 · Facsimile: +44 (0) 1670 829465 · Email: info@welwyn-tt.com · Website: www.welwyn-tt.com
121
Setting breakpoints under KITL is invalid?
When implementing KITL via USB, the kernel debugger shows that it has established a connection, but the breakpoints set on the driver are invalid? Can KITL be implemented and the driver debugged in th...
bingfo Embedded System
How to write this Verilog statement in VHDL?
assign sync= ({din, rx_sync[6:1]} == 7'b010_1101);...
scyshuier FPGA/CPLD
【Aigtek Instrument Peripherals】Do you know how to use a dotting machine?
Do you know how to use a dotting machine?...
aigtekatdz Test/Measurement
How to add a triax to LSM6DSL
I want to use 6 axes plus 3 axes, how should I configure it? Thank you. Usage is as shown in the figure...
曹伟1993 MEMS sensors
AD9253 data acquisition problem
I would like to ask, the test mode of ad9253 can collect data, but when using an external source, wrong data will appear. What is the situation?...
yangxuchen ADI Reference Circuit
Let's learn MSP430F6638 - Basics of UCS (3)
[align=center] [size=4][b]Basics of Unified Clock System UCS[/b][/size][/align] Continuing from the previous post, let's learn MSP430F6638-Basics of GPIO. Debugging a program is really hard. I spent t...
jqh_111 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 243  317  251  2451  857  5  7  6  50  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号