EEWORLDEEWORLDEEWORLD

Part Number

Search

LAS395R3JLF

Description
Wirewound Resistors - Through Hole
CategoryPassive components   
File Size356KB,3 Pages
ManufacturerTT Electronics
Download Datasheet Parametric View All

LAS395R3JLF Overview

Wirewound Resistors - Through Hole

LAS395R3JLF Parametric

Parameter NameAttribute value
Product AttributeAttribute Value
ManufacturerTT Electronics
Product CategoryWirewound Resistors - Through Hole
TechnologyWirewound
Mounting StylePCB Mount
Resistors
Low Cost Semi-Precision
Power Wirewound Resistor
Low Cost Semi-Precision
LAS Series
Power Wirewound Resistor
1 and 3 watts
0.1 ohm
LAS Series
to 18K ohms
1
Color
watts
identification
and 3
band
0.1 ohm to 18K ohms
±5%, ±3%, ±1%, ±.5% tolerance
Color band identification
Resistance wire TCR ±20 ppm/°C
±5%, ±3%, ±1%, ±.5% tolerance
RoHS-compliant version available
Resistance wire TCR ±20 ppm/°C
RoHS-compliant version available
½llo½ resistance wirewound
to speci½ic parameters includin½
TCR½s ½rom ±20 to ½5500 ppm/°C
½ll welded
cap and lead
Colorband
½ar½in½
All Pb-free parts comply with EU Directive 2011/65/EU (RoHS2)
Heat conductin½
ceramic substrate
Silicone
con½ormal coatin½
Electrical Data
IRC
Type
LAS-1
LAS-3
Power Rating 275°C
Max. Hot Spot
125°C
1
2
25°C
2
3
Commercial Range
(ohms)
Min.
0.1
0.1
Max.
7.5K
18K
Non-Inductive Range
(ohms)
Min.
0.1
0.2
Max.
3.8K
7.5K
Available Resistance
(ohms)
0.5%, 1%
1 - 7.5K
1 - 18K
3%, 5%
0.1 - 7.5K
0.1 - 18K
Environmental Data
Test Condition (@ 25°C)
Load Life 1000 hours
Moisture Resistance
Temperature Cycle
Short Time Overload
Low Temperature Operation
Solder Heat
Shock
Vibration
LAS-3 Carbon Comp Replacement (contact factory)
The L½S-3 is a three watt con½ormal coated precision wirewound resistor. The resistance wire is welded to the end caps and
wound on alumina rod ½or ½ood thermal conductivit½. In circuit applications that utilize two watt carbon comp resistors the L½S-3
is an idead e½½ective replacement. The L½S-3 5.6 ohm can be specificall½ desi½ned to withstand 22 jooules o½ ener½½ delivered
b½ a 1000 volt 10 x 1000 usec wave shape pulse.
LIGHTNING SURGE
Special L½S-3 5.6 ohm to 100 ohm will meet
Telecom GR-1089 li½htnin½ requirements.
V = 1000 volts
T1 = 10 usec rise
T2 = 1000 usec to V2
10 ohm output impedance
V
Max
∆R
1.0%
1.0%
0.5%
0.5%
0.5%
0.25%
0.5%
0.5%
V2
0
T1
MICROSECONDS
T2
General Note
IRC reserves the right to make changes in product specification without notice or liability.
General Note
All information is subject to IRC’s own data and is considered accurate at time of going to print.
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going
Wire and Film Technologies Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
to print.
BI Technologies IRC Welwyn
A subsidiary of
TT electronics plc
http://www.ttelectronics.com/resistors
LAS Series Issue October 2008 Sheet 1 of 3
© TT Electronics plc
04.17
[Keysight Call for Papers] Agilent Oscilloscope - Engineer's "Heavenly Sword"
[i=s]This post was last edited by gurou1 on 2017-3-27 19:15[/i] I saw this forum event and I happened to be using an Agilent oscilloscope in my studies and work. I would like to share my story with th...
gurou1 Test/Measurement
Please recommend a cheap and good quality Bluetooth module for MCU system
It can be a serial port or a SPI interface....
毛毛虫 Embedded System
Help, my customized system cannot display Chinese??
Strange, the customized system in pb5.0 can't display Chinese, only "_" can be displayed, but when using mobile Hansheld as the system, Chinese can be displayed. What's going on?...
lytton50 Embedded System
Circuit Diagram 22-Analysis of Bistable Trigger Circuit Principle
[i=s]This post was last edited by tiankai001 on 2018-2-11 13:52[/i] [align=left][color=rgb(34, 34, 34)][font="]The bistable trigger is one of the basic triggers commonly used in pulse and digital circ...
tiankai001 Integrated technical exchanges
How to port 51 program to STM32 program? Please give me some guidance!
I have the 51 program of this screen JLX12864G-086-PC. Now I want to change it to be used in STM32. How can I change it? ? ? Attached is the 51 program of the screen. Please guide me! ! ! !...
wkiddw stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1506  643  2663  139  1560  31  13  54  3  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号