EEWORLDEEWORLDEEWORLD

Part Number

Search

800-012-07Z17-25EX

Description
Circular Connector
CategoryThe connector   
File Size1MB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

800-012-07Z17-25EX Overview

Circular Connector

800-012-07Z17-25EX Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerGlenair
Reach Compliance Codecompliant
Base Number Matches1
Series 800 Mighty Mouse UN Mating Thread
PC Tail or Solder Cup PCB Receptacle
800-012 and 800-040 Ordering Information
Printed Circuit Board/ Solder Cup Receptacles
feature low profile shells for
minimum protrusion inside enclosures and integral board standoffs. Contacts are
non-removable.
Water Immersion, Unmated
Specify
800-012
connectors for applications where
open face water immersion is not a requirement. For MIL-STD-810 Method 512G
immersion requirements, specify
800-040
watertight connectors . These 800-040
connectors are specially sealed (“MOD-518”) and are 100% tested to maintain a
helium leak rate of 1 x 10
-4
cc/second at one atmosphere pressure differential from
-40C to +70C.
How To Order
C
Shell
Size
Series 800
Sample Part Number
Series
Shell Style (See Table I)
-02
= Square Flange
Shell Material and Finish
Shell Size - Insert
Arrangement
Contact Type
Shell Key Position
(See Table II)
P
= Pin, PC Tail
S
= Socket , PC Tail
N
= Normal
800-012
800-012
=
Receptacle for Solder Cup or PCB Termination, with Standard
Epoxy Potting
800-040
=
Receptacle for Solder Cup or PCB Termination, With Special
“MOD-518” Sealing For Open Face (Unmated) Water Immersion
Requirements. 100% Leak Tested.
-07
= Jam Nut
(See
Jam Nut Panel Cutout Dimensions Page C-3)
C
= Aluminum / Black Anodize (Non-Conductive) RoHS Compliant
M
= Aluminum / Electroless Nickel RoHS Compliant
NF
= Aluminum / Cadmium with Olive Drab Chromate
ZNU
= Aluminum / Zinc-Nickel with Black Chromate
MT
= Aluminum / Nickel-PTFE RoHS Compliant
Z1
= Stainless Steel / Passivated RoHS Compliant
See Contact Arrangements page C-2
E
= Pin, Solder Cup
F
= Socket, Solder Cup
Y
= Pos. Y
Z
= Pos. Z
-07
M
7-10
P
Z
X
= Pos. X
Table I: Shell Style
ØM
in
.318
.386
.449
.510
.574
.635
.760
mm
8.08
9.80
11.40
12.95
14.58
16.13
19.30
Recommended Panel Cut Out
N Flat ± .002
in
.297/.292
.365/.360
.429/.424
.483
.540
.614
.722
mm
7.54/7.42
9.27/9.14
10.90/10.77
12.67
13.71
15.60
18.34
øM
N FLAT
-02
Square Flange Front Mount
-07
Jam Nut for Rear Panel
Mounting
5
6
7
8
9
10
12
Dimensions in Inches (millimeters) are subject to change without notice.
© 2014 Glenair, Inc.
Series 80 Mighty Mouse
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
C-12
E-Mail: sales@glenair.com
Help: How to use Altera FFT IP core on FPGA board
I use FPGA to implement a spectrum analyzer and use the on-chip FFP IP core to perform spectrum analysis. I calculate the square sum of the real and imaginary parts and take the logarithm to generate ...
when_Qi FPGA/CPLD
MPLAB editor has red lines everywhere
The code is all red line alarm, but the compilation can pass, please solve it... It affects the programming too much, I thought it was all wrong...
apleilx Microchip MCU
How to remove the seal?
[i=s]This post was last edited by paulhyde on 2014-9-15 03:17[/i] It has just been blocked, how can I unblock it?...
bophic Electronics Design Contest
[Homemade op amp] Can anyone recommend some books or materials on making op amps? [I would like to thank TAT]
Because I need to make an op amp myself recently, but I feel that the static operating points are not set well, and the effect is not good. . What I mean by making an op amp is to use transistors dire...
cinbow Analog electronics
Help post: About IR2110 driver problem
[i=s]This post was last edited by paulhyde on 2014-9-15 03:48[/i] I recently built a IR2110 driver circuit. When I used an oscilloscope to look at the low-end output, the waveform was a normal square ...
DairyQ Electronics Design Contest
Application of LM324 quad op amp.pdf
[i=s] This post was last edited by paulhyde on 2014-9-15 09:28 [/i] It is very useful in the competition~~~...
贺增甫 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1272  2181  1270  2790  201  26  44  57  5  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号