P/N: B-1x/1x-155(C)-F-SSC3x(-G5)
155 Mbps Bi-directional Receptacle Single Fiber Transceiver
Features
Diplexer Single Mode Single Fiber 2x5 SFF SC
Receptacle connector
Wavelength Tx 1310nm/Rx 1530 nm
(B-13/15-155(C)-F-SSC3x)
Wavelength Tx 1530nm/Rx 1310 nm
(B-15/13-155(C)-F-SSC3x)
SONET OC-3 SDH STM-1 Compliant
Single +3.3V Power Supply
LVPECL Differential Inputs and Outputs
(B-1x/1x-155-F-SSC3x)
LVTTL Differential Inputs and Outputs
(B-1x/1x-155C-F-SSC3x)
Wave Solderable and Aqueous Washable
Class 1 Laser Int. Safety Standard IEC-825 Compliant
Uncooled Laser diode with MQW structure
Complies with Telcordia (Bellcore) GR-468-CORE
EMI Shielding Finger Optional
RoHS compliance available
Table 1 – Absolute Maximum Rating
Parameter
Power Supply Voltage
Output Current
Soldering Temperature
Storage Temperature
Storage Temperature
Symbol
Vcc
I
out
-
Tstg
Tstg
Min.
0
-
-
0
-40
Typical
-
-
-
-
-
Max.
3.6
30
260
70
85
Unit
V
mA
ºC
ºC
ºC
1
2
3
Notes
Note 1: 10 senconds on leads only
Note 2: B-1x/1x-155(C)-F-SSC3(S)
Note 3: B-1x/1x-155(C)-F-SSC3A(S)
Table 2 – Recommended Operating Condition
Parameter
Power Supply Voltage
Operating Temperature (Case)
Data Rate
Symbol
Vcc
Topr
DR
Min.
3.1
0
-
Typical
3.3
-
155
Max.
3.5
70
-
Unit
V
ºC
Mbps
Notes
4
Note 4: please refer to ordering information
-1-
DS-5750
Rev 0.0 2009-09-04
P/N: B-1x/1x-155(C)-F-SSC3x(-G5)
155 Mbps Bi-directional Receptacle Single Fiber Transceiver
Table 3 – Transmitter Specifications (Optical)
Parameter
Optical Transmit Power
Output Center Wavelength
Output Center Wavelength
Output Spectrum Width
Extinction Ratio
Output Eye
Optical Rise/Fall Time
Optical Isolation
Relative Intensity Noise
Total Jitter
Symbol
P
o
λ
c
λ
c
Δλ
ER
t
r
/t
f
-
RIN
T
J
Min.
-14
1260
1480
-
8.2
-
30
-
-
Typical
-
1310
1530
-
-
-
-
-
-
Max.
-8
1360
1580
3
-
2
-
-116
1.0
Unit
dBm
nm
nm
nm
dB
ns
dB
dB/Hz
ns
11
9
10
Notes
5
6
7
8
Compliant with ITU-T recommendation G.957/STM-1
Note 5: Output power is coupled into a 9/125
µm single mode fiber
Note 6: B-13/15-155(C)-F-SSC3x
Note 7: B-15/13-155(C)-F-SSC3x
Note 8: RMS (σ)
Note 9: 10% to 90% Values
Note 10: Tx: 1310 nm/ Rx: 1550 nm
Note 11: Measured with 2
23
-1 PRBS with 72 ones and 72 zeros.
Table 4 – Transmitter Specifications (Electrical)
Parameter
Power Supply Current
Data Input Current-Low
Data Input Current-High
Differential Input Voltage
Data Input Voltage-Low
Data Input Voltage-High
Symbol
I
CC
I
IL
I
IH
V
IH
-V
IL
V
IL
-V
CC
V
IH
-V
CC
Min.
-
-350
-
300
-2.0
-1.1
Typical
-
-
-
-
-
-
Max.
140
-
350
-
-1.58
-0.74
Unit
mA
μA
μA
mV
mV
mV
13
Notes
12
Note 12: Maximum current is specified at Vcc=Maximum @ maximum temperature
Note 13: These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs
-2-
DS-5750
Rev 0.0 2009-09-04
P/N: B-1x/1x-155(C)-F-SSC3x(-G5)
155 Mbps Bi-directional Receptacle Single Fiber Transceiver
Table 5 – Receiver Specifications (Optical)
Parameter
Sensitivity
Maximum Input Power
Signal Detect-Asserted
Signal Detect-Deasserted
Signal Detect-Hysteresis
Cross Talk
Wavelength of Operation
Wavelength of Operation
Symbol
-
P
in
Pa
Pd
-
-
Min.
-
-3
-
-45
1.0
-
1480
1260
Typical
-
-
-
-
-
-
-
-
Max.
-33
-
-33
-
4.0
-33
1600
1360
Unit
dBm
dBm
dBm
dBm
dB
dB
nm
nm
17
18
15
16
Notes
14
Note 14: Measured with 2
23-1
PRBS, BER = 10
-10
.
Note 15: Measured on transition: low to high, The SD level should be deasserted when fiber disconnected
Note 16: The SD level should be deasserted when fiber is disconnected
Note 17: B-13/15-155(C)-F-SSC3x
Note 18: B-15/13-155(C)-F-SSC3x
Table 6 – Receiver Specifications (Electrical)
Parameter
Power Supply Current
Data Output Voltage-Low
Data Output Voltage-High
Signal Detect Output Voltage-Low
Signal Detect Output Voltage-High
Signal Detect Output Voltage-Low
Signal Detect Output Voltage-High
Symbol
I
CC
V
OL
-V
CC
V
OH
-V
CC
V
SDL
-V
CC
V
SDH
-V
CC
V
SDL
-V
CC
V
SDH
-V
CC
Min.
-
-2.0
-1.1
-2.0
-1.1
-
2.0
Typical
-
-
-
-
-
-
-
Max.
100
-1.58
-0.74
-1.58
-0.74
0.5
-
Unit
mA
V
V
V
V
V
V
Notes
19
20
21
22
Note 19: The current excludes the output load current
Note 20: These outputs are compatible with 10K, 10KH and 100KECL and LVPECL outputs.
Note 21: LVPECL, B-1x/1x-155-F-SLC3x
Note 22: LVPECL, B-1x/1x-155C-F-SLC3x
-3-
DS-5750
Rev 0.0 2009-09-04
P/N: B-1x/1x-155(C)-F-SSC3x(-G5)
155 Mbps Bi-directional Receptacle Single Fiber Transceiver
Connection Diagram
Table 7 – Pin Definitions
Pin
1
2
3
4
5
6
7
8
9
10
Unit
RxGND
RxVcc
SD
RD-
RD+
TxVcc
TxGND
TxDIS
TD+
TD-
Notes
Directly connect this pin to the receiver ground plane
+3.3V dc power for the receiver section
Active high on this indicates a received optical signal(LVPECL/LVTTL)
Receiver Data Out Bar(LVPECL)
Receiver Data Out (LVPECL)
+3.3V dc power for the transmitter section
Directly connect this pin to the tranmitter ground plane
Transmitter disable(LVTTL)
Transmitter Data In (LVPECL)
Transmitter Data In Bar (LVPECL)
-4-
DS-5750
Rev 0.0 2009-09-04
P/N: B-1x/1x-155(C)-F-SSC3x(-G5)
155 Mbps Bi-directional Receptacle Single Fiber Transceiver
Recommended Circuit Schematic
B-1x/1x-155-F-SSC3x(-G5)
PHY DEVICE
TERMINATE AT
TRANSCEIVER INPUTS
Vcc(+3.3V)
Z=50
Ω
TD-
100
Ω
LVPECL
Z=50
Ω
130
Ω
130
Ω
TD+
Tx Disable
LVTTL
10
TD-
9
TD+
8
TxDIS
7
TxGND
6
1
μ
H
TxVcc
C2
Vcc(+3.3V)
C3
Tx
RxGND
RxVcc
10
μ
F
Rx
RD+
RD-
SD
1
μ
H
C1
RD+
Vcc(+3.3V)
1
2
3
4
5
Z=50
Ω
100
Ω
LVPECL
RD-
Z=50
Ω
130
Ω
130
Ω
Z=50
Ω
Vcc(+3.3V)
130
Ω
SD
LVPECL
82
Ω
NOTE:C1=C2=C3=100nF
TERMINATE AT
DEVICE INPUTS
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
-5-
DS-5750
Rev 0.0 2009-09-04
京公网安备 11010802033920号
EEWORLD
