EEWORLDEEWORLDEEWORLD

Part Number

Search

ALD2704BDA

Description
DUAL OP-AMP, 4000 uV OFFSET-MAX, 2.1 MHz BAND WIDTH, CDIP8
CategoryAnalog mixed-signal IC    Amplifier circuit   
File Size44KB,6 Pages
ManufacturerALD [Advanced Linear Devices]
Download Datasheet Parametric View All

ALD2704BDA Overview

DUAL OP-AMP, 4000 uV OFFSET-MAX, 2.1 MHz BAND WIDTH, CDIP8

ALD2704BDA Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Parts packaging codeDIP
package instructionCERDIP-8
Contacts8
Reach Compliance Codeunknow
ECCN codeEAR99
Amplifier typeOPERATIONAL AMPLIFIER
Maximum average bias current (IIB)0.01 µA
Nominal Common Mode Rejection Ratio83 dB
Maximum input offset voltage4000 µV
JESD-30 codeR-GDIP-T8
Humidity sensitivity level1
Negative supply voltage upper limit-6.6 V
Nominal Negative Supply Voltage (Vsup)-5 V
Number of functions2
Number of terminals8
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package body materialCERAMIC, GLASS-SEALED
Package shapeRECTANGULAR
Package formIN-LINE
Peak Reflow Temperature (Celsius)225
Certification statusNot Qualified
Nominal slew rate5 V/us
Supply voltage upper limit6.6 V
Nominal supply voltage (Vsup)5 V
surface mountNO
technologyCMOS
Temperature levelMILITARY
Terminal formTHROUGH-HOLE
Terminal locationDUAL
Maximum time at peak reflow temperatureNOT SPECIFIED
Nominal Uniform Gain Bandwidth2100 kHz
Base Number Matches1
A
DVANCED
L
INEAR
D
EVICES,
I
NC.
ALD2704A/ALD2704B
ALD2704
DUAL RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER
GENERAL DESCRIPTION
The ALD2704 is a dual monolithic operational amplifier with MOSFET
input that has rail-to-rail input and output voltage ranges. The input
voltage range and output voltage range are very close to the positive and
negative power supply voltages. Typically the input voltage can be
beyond positive power supply voltage V + or the negative power supply
voltage V- by up to 300mV. The output voltage swings to within 60mV of
either positive or negative power supply voltages at rated load.
With high impedance load, the output voltage of the ALD2704 ap-
proaches within 1mV of the power supply rails. This device is designed
as an alternative to the popular J-FET input operational amplifier in
applications where lower operating voltages, such as 9V battery or
±3.25V
to
±6V
power supplies are being used. The ALD2704 offers high slew rate
of 5V/µs. It is designed and manufactured with Advanced Linear Devices'
standard enhanced ACMOS silicon gate CMOS process, and it offers low
unit cost and exceptional reliability.
The rail-to-rail input and output feature of the ALD2704 expands signal
voltage range for a given operating supply voltage and allows numerous
analog serial stages to be implemented without losing operating voltage
margin. The output stage is designed to drive up to 10mA into 400pF
capacitive and 1.5KΩ resistive loads at unity gain and up to 4000pF at a
gain of 5. Short circuit protection to either ground or the power supply rails
is at approximately 15mA clamp current. Due to complementary output
stage design, the output can source and sink 10mA into a load with
symmetrical drive and is ideally suited for applications where push-pull
voltage drive is desired.
For each of the operational amplifier, the offset voltage is trimmed on-chip
to eliminate the need for external nulling in many applications. For
precision applications, the output is designed to settle to 0.1% in 2µs. In
large signal buffer applications, the operational amplifier can function as
an ultrahigh input impedance voltage follower /buffer that allows input and
output voltage swings from positive to negative supply voltages. This
feature is intended to greatly simplify systems design and eliminate higher
voltage power supplies in many applications.
FEATURES
Rail-to-rail input and output voltage ranges
Symmetrical push-pull output drives
Output settles to 2mV of supply rails
5.0V/µs slew rate
High capacitive load capability -- up to 4000pF
No frequency compensation required -- unity
gain stable
Extremely low input bias currents -- <1.0pA
typical (20pA max.)
Ideal for high source impedance applications
High voltage gain -- typically 100V/mV
Output short circuit protected
Unity gain bandwidth of 2.1MHz
APPLICATIONS
Voltage amplifier
Voltage follower/buffer
Charge integrator
Photodiode amplifier
Data acquisition systems
High performance portable instruments
Signal conditioning circuits
Low leakage amplifiers
Active filters
Sample/Hold amplifier
Picoammeter
Current to voltage converter
Coaxial cable driver
Capacitive sensor amplifier
Piezoelectric transducer amplifier
PIN CONFIGURATION
ORDERING INFORMATION
Operating Temperature Range*
-55°C to +125°C
0°C to +70°C
0°C to +70°C
8-Pin
CERDIP
Package
ALD2704A DA
ALD2704B DA
ALD2704 DA
8-Pin
Small Outline
Package (SOIC)
ALD2704A SA
ALD2704B SA
ALD2704 SA
8-Pin
Plastic Dip
Package
ALD2704A PA
ALD2704B PA
ALD2704 PA
OUT
A
-IN
A
+IN
A
V-
1
2
3
4
TOP VIEW
DA, PA, SA PACKAGE
8
7
6
5
V+
OUT
B
-IN
B
+IN
B
* Contact factory for industrial temperature range
© 1998 Advanced Linear Devices, Inc. 415 Tasman Drive, Sunnyvale, California 94089 -1706 Tel: (408) 747-1155 Fax: (408) 747-1286 http://www.aldinc.com
About the production of pc104 bus driver
I just made a DA board based on pc104 bus, but now I need to interact with 3350 motherboard based on pc104 bus, mainly to read the data of pc104 bus, so I need to make a driver. This is my first time ...
senorspring Embedded System
[ATMEL technical problem] About the AT91R40008 startup code problem under KEIL
Use KEIL software to create a project, and automatically generate a startup code STartup.S; But the problem is, this code is a bit incomprehensible, and the compilation error is oh, please give me som...
eeleader Microcontroller MCU
STMicroelectronics SiC products and industrial application guide live data collection
Live broadcast collection Award-winning live broadcast: STMicroelectronics SiC products and industrial application guideLive playback:Click to watchLive Documentation: Click to downloadLive QA:1. What...
EEWORLD社区 Energy Infrastructure?
Does AVR have the same IO port bit operation as 51?
#define Set_Bit(val, bitn) (val |=(1<<(bitn))) #define Clr_Bit(val, bitn) (val&=~(1<<(bitn))) #define Get_Bit(val, bitn) (val &(1<<(bitn)) ) As above, who can explain in detail what the above means? I...
gh131413 Microchip MCU
Research on Embedded Linux Operating System
Based on the research of Linux kernel and Linux application environment, the method of operating system module decomposition and improvement is adopted to realize the embedded Linux operating system t...
frozenviolet Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 919  2115  96  1195  176  19  43  2  25  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号