SpecMat-H
Static Dissipative Homogeneous Material
The SpecMat-H homogeneous material is a single-layer, ESD-safe
thermoplastic vinyl made for bench tops. Without adding cost, the
extruded manufacturing process used to produce this high-per-
formance vinyl utilizes superior plasticizers and lower-outgassing
solvents, unlike ESD vinyl made by cast coating.
The proprietary polymers used to manufacture this material are
homogeneously dispersed with a migratory anti-static formula that
allows for both surface and volume resistance. By design, anti-static
properties cannot be worn away through wear or outgassing.
Color shown is a representation and may vary
Maintenance
:
Resistant to solder, heat, and most common solvents, SpecMat-H
is an economical choice for static- sensitive production areas in
electronics manufacturing and laboratories. Tray mats can be cus-
tom-cut with a sharp blade. Scraps can be recycled.
Blended with hydrophilic molecules to control the speed of dissipa-
tion, the ESD-Homogeneous material will deliver a typical resis-
tance-to-ground measurement of 10
8
-10
9
ohms per ANSI/ESD S4.1.
ESD-Homogeneous material complies with industry standards
including EN 61340-5-1: Protection of Electronic Devices from Elec-
trostatic Phenomena and ANSI ESD S20.20: Protection of Electrical
and Electronic Parts, Assemblies and Equipment.
0.10” (2.54 mm) thickness
10
8
- 10
9
ohms, ohm per cm RTG, RTT, Vol R
Can be custom-cut with sharp blade; scraps are recyclable
Embossed finish reduces light glare and parts slippage
Durable surface withstands high temperatures, solder, flux, and
harsh chemicals
Low outgassing and VOC are ideal for controlled environments
To keep mats clean and avoid insulative
electrical readings, use a neutral cleaner
such as the 6001 Mat and Table Top
Cleaner. The low alcohol, high surfac-
tant formula will allow deep cleaning
without damaging the structural integ-
rity of the SpecMat-H material.
SpecMat-H roll
62100 light blue 24” x 40’
62300 light blue 30” x 40’
62500 light blue 36” x40’
SpecMat-H cut mats
are available in various
sizes. Each mat includes two 10mm female
ground snaps. Ground cords sold separately.
this product, including smoke and flame
inhibitors, are RoHS compliant and are not
listed on the REACH SvHC list.
Rolls and cut mats are made in the U.S.A.
and can be shipped under NAFTA rules.
The components
used to manufacture
Passes weathering ozone resistance per ASTM D178-01
Passes and exceeds minimum standards for NFPA fire and
smoke safety
UV additives to protect color and eliminate fading
Warranty:
ACL Inc., offers an exclusive lifetime warranty on the electrical resistance (10
8
– 10
9
ohms) properties of the SpecMat-H table mats. If the electrical properties should fail
(when tested to ANSI / ESD S20.20) on any of our table mats during the lifetime of the
mat due to manufacturing or physical defects, we will replace the mat free of charge.
This warranty does not apply to mats that are abused, improperly used, or cleaned with
mat cleaners not tested and approved by ACL Inc.
840 W. 49th Place · Chicago, IL 60609
800.782.8420 · 847.981.9212 · fax 847.981.9278
info@aclstaticide.com · www.aclstaticide.com
ACL Inc. registered to
ISO-9001 : 2008
Certificate No. 10002746
rev. January 5, 2015 mkb
stm32/stm8
京公网安备 11010802033920号
EEWORLD
