EEWORLDEEWORLDEEWORLD

Part Number

Search

8533T1ZBE12

Description
OCXO, CLOCK, 12.8 MHz, HCMOS OUTPUT
Categorysemiconductor    Analog mixed-signal IC   
File Size359KB,5 Pages
ManufacturerITT
Websitehttp://www.ittcannon.com/
Download Datasheet Parametric View All

8533T1ZBE12 Overview

OCXO, CLOCK, 12.8 MHz, HCMOS OUTPUT

8533T1ZBE12 Parametric

Parameter NameAttribute value
Maximum operating temperature70 Cel
Minimum operating temperature0.0 Cel
Maximum supply voltage3.46 V
Minimum supply voltage3.14 V
Rated supply voltage3.3 V
Rated operating frequency12.8 MHz
stateACTIVE
terminal coatingNOT SPECIFIED
Installation featuresThrough hole mounting
DimensionsL25.7XB25.7XH13.2 (mm)/L1.012XB1.012XH0.52 (inch)
Ageing4 PPM/20 YEAR
Frequency converter0
frequency stable voltage0.0020 ppm
input power1.25 W
Manufacturer Series760
Vibration typeHCMOS
Industrial supply voltage3.3V
Heating power5 W
C&K 8500 Series
Subminiature Pushbutton Switches
A
Pushbutton
Features/Benefits
Pre-travel or over-travel models
available
Ratings up to 3 AMPS
Reliable contact design
RoHS compliant
Typical Applications
Detection
Telecommunications and
networking equipment
Computers and peripherals
Models Available
Specifications
CONTACT RATING: Q contact material (853X Models): 1 AMP @
120 V AC or 28 V DC; (855X Models): 3 AMPS @ 120 V AC or
28 V DC. See page A-63 for additional ratings.
ELECTRICAL LIFE:
853X MODELS: 250,000 actuations at full load.
855X MODELS: 10,000 actuations at full load.
CONTACT RESISTANCE: Below 30 mΩ typ. initial @
2-4 V DC, 100 mA, for both silver and gold plated contacts.
INSULATION RESISTANCE: 109
min.
DIELECTRIC STRENGTH: 1,000 Vrms min. @ sea level.
OPERATING TEMPERATURE: –30ºC to 65ºC.
NOTE:
Any models supplied with Q, B or G contact material are RoHS compliant. For the
latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs.
NOTE:
Specifications and materials listed above are for switches with standard options.
For information on specific and custom switches, consult Customer Service Center.
Materials
CASE: Glass filled phenolic or diallyl phthalate (DAP) (UL 94V-0).
PLUNGER: Phenolic or glass filled polyester, black standard(UL94V-0).
CAP & FRAME: Nylon, black, standard.
BUSHING: Brass, nickel plated.
CONTACTS: Q contact material: Coin silver, silver plated. See page
A-63 for additional contact materials.
TERMINALS: Q contact material: Copper alloy, silver plated. See page
A-63 for additional contact materials.
TERMINAL SEAL: Epoxy.
HARDWARE: Nut: Brass, nickel plated; Lockwasher: Steel, bright
nickel plated.
Build-A-Switch
To order, simply select desired option from each category and place in the appropriate box. Available options are shown
and described on pages A-61 thru A-64. For additional options not shown in catalog, consult Customer Service Center. All
models have epoxy terminal seal and are compatible with all “bottom-wash” PCB cleaning methods.
Switch Function
8531
SPST Off-Mom. 1 Amp
8532
SPST Off-Mom. 1 Amp
8533
SPST On-Mom. 1 Amp
8534
SPST On-Mom. 1 Amp
8551
SPST Off-Mom. 3 Amps
8552
SPST Off-Mom. 3 Amps
Actuator or Plunger
M
.150" high
J81
Snap-in with frame
J82
Snap-in with frame for LED
S
.210" high
T
15/32 bushing
T1
15/32 bushing with frame
(8532 and 8534 only)
Terminations
Z
Solder lug
AV
Right angle, PC thru-hole
C
PC Thru-hole
Contact Material
Q
Silver
B
Gold
Seal
G
Gold over silver
E
Epoxy
D
No epoxy seal
Cap or Plunger Color
2
Black
1
White
Frame Color
3
Red
2
Black
9
Gray
NONE
Models without frame
Dimensions are shown: Inches (mm)
Specifications and dimensions subject to change
A–60
www.ittcannon.com
STM32 output 4-20MA or 0-10V circuit sharing
Is it feasible?...
常伴久久 ADI Reference Circuit
Mass production of USB flash drives
I have an 8G USB flash drive, which can be recognized but cannot be formatted! I am preparing to mass produce it, but I don't know which memory chip to choose. The maximum after mass production is 3.5...
qu27jump Embedded System
Multisim simulation is so slow...
I use it to simulate sequential logic circuits and wait for a long time... Is there any way to set the simulation speed? ?...
yangliu Embedded System
Regarding the LM3S8962 development board, after installing the driver, the MDK has no options.
It is good to find it on the Internet and can solve practical problemsYes, you can. Just modify the TOOLS file. 1: Modify the two places CPUDLL1=SARMCM3.DLL(TDRV1,TDRV2,TDRV3,TDRV4,TDRV5,TDRV7,TDRV8,T...
ddllxxrr Microcontroller MCU
Questions about the front-end loading process of the touch driver in wince5.0
Hello, seniors. I am a newcomer who has just joined the company. I am lucky to be able to do system development like you experts. However, our company is engaged in chip manufacturing. I am working on...
shizhu72 Embedded System
bin file modification
I want to ask, I have a hardware bin file, and I want to modify the bmp picture in the file. How can I modify it?...
zhp3245 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1846  1212  2186  1875  2693  38  25  45  55  46 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号